Datalogic DRAGON D101 Quick Reference

QUICK REFERENCE INSTALLAZIONE RAPIDA INSTALLATION RAPIDE SCHNELLINSTALLATION 820000852 (Rev. B) ll-g ides com

UK DRAGON™ D READERS automatically scan barcodes at a distance. Simply aim and pull the trigger. Code scanning is performed along the scan line emitted from the reading wiindow. This line must cross the entire code. Successful scanning is obtained by tilting the reader with respect to the barcode to avoid direct reflections which impair the reading performance(see the figure above). I I lettori DRAGON™ D leggono i codici a barre a distanza: è sufficiente mirare sul codice e premere il grilletto. La lettura avviene sulla linea laser che deve attraversare interamente il codice da leggere. Le condizioni ottimali per la lettura si ottengono inclinando il lettore rispetto al codice, così da evitare riflessioni dirette, che potrebbero compromettere le prestazioni di lettura (vedere la figura qui sopra). F Les lecteurs DRAGON™ D lisent les codes à distance. Il est suffisant de viser le code.Le code est lit sur la ligne sortant de la fenêtre de lecture de l'appareil. Cette ligne doit traverser le code à barres à lire de part en part. Pour des prestations optimales inclinez la douchette par rapport au code à lire, afin d'éviter des réflexions directes qui pourraient compromettre la performance de lecture (voir la figure ci-dessus). D Die DRAGON™ D Leser lesen Strichcodes berührungslos. Es genügt auf den Code zu zielen und abzudrücken. Der Code wird mittels einer Lichtlinie gelesen, die das Gerät durch das Lesefenster verläßt und den gesamten Code durchqueren muß. Eine optimale Lesegarantie ist gewährleistet, wenn der Benutzer den Leser bzgl. dem Code etwas neigt, um eine direkte Reflexion zu vermeiden, wie im Bild oben gezeigt wird.

programmable aiming system. If enabled, the scan line emitted from the reading window is preceded by a red spot which must illuminate the code center to get the best reading performance (see figure above, c). Once the defined timeout is reached, the red spot disappears and is followed by the scan line to start the code scanning. I I modelli DRAGON™ D101 e DRAGON™ D101 LR offrono un sistema di puntamento programmabile. Se attivato, uno spot rosso illumina il codice precedendo l'emissione della linea laser. Per ottenere la massima prestazione di lettura è necessario centrarlo sul codice stesso (vedi figura sopra, c). Lo spot scomparirà una volta terminato il timeout precedentemente definito e seguirà l'emissione della linea laser per avviare la lettura. F Les modèles DRAGON™ D101 et DRAGON™ D101 LR fournissent un système de pointage programmable. Si le système est activé, un spot rouge, qui précéde la sortie de la ligne de lecture, illumine le code à lire. Le spot doit être centré sur le code pour obtenir la meilleure performance de lecture (voir la figure ci-dessus, c). Une fois le "timeout" terminé, le spot rouge est suivi par la ligne de lecture. D Die DRAGON™ D101 und DRAGON™ D101 LR Modelle bieten ein programmierbares Zielsystem. Wenn das System ein ist, zuerst verläßt der Leser ein rotes und rundes Licht und dann die Lichtlinie. Das rundes Licht muß mittels des Codes sich befinden, um die beste Leseleistung zu erreichen (siehe Bild oben , c). Wenn das Lichttimeout geendet ist, schaltet das rotes und rundes Licht ab. Dann verläßt der Leser die Lichtlinie, um den Code zu lesen.

aiming system timeout. I Leggere uno dei codici seguenti per impostare il timeout del sistema di puntamento. F Lire l'un des codes suivants pour sélectionner le "timeout" du système de pointage que vous désirez. D Lesen Sie einen der folgenden Codes, um das Zielsystemstimeout einzustellen. ♦aiming system disabled i#9"k i#9"k i#9"k 300 ms i#9'k i#9'k i#9'k 500 ms i#9,k i#9,k i#9,k 1 sec i#91k i#91k i#91k

Electrical Features D101 D101 HD D101 LR Power supply 4 to 20 Vdc Consumption @ 4V @ 5V @ 20V Sleep mode 250 mA 170 mA 40 mA 2 mA Scan rate 35 ± 5 scans/sec Typical reading field width see reading diagrams Max. resolution mm mils 0.08 3 0.06 2.5 0.25 10 PCS minimum (Datalogic Test Chart) 15% 40% 40% Indicators Laser On LED (red) Good Read LED (green) Beeper Laser Features Power (max) in mW 0.9 0.4 1.4 Scan angle 42° 37° 23° Laser Safety Class EN 60825-1 / CDRH 2 Environmental Features Working Temperature -10° to +50 °C 0° to +40 °C -10° to +50 °C Storage Temperature -20° to +50 °C Humidity 90% non condensing Drop resistance IEC 68-2-32 Test ED Protection sealed against rain and dust Mechanical Features Weight (without cable) About 270 g. Cable length 2 m

DRAGON™ D101 12 24 36 48 60 96 36 24 12 0 12 24 36 cm 72 84 108 cm 0.19 mm (7.5 mils) 0.25 mm (10 mils) 0.33 mm (13 mils) 0.50 mm (20 mils) 1.00 mm (40 mils) 1.38 mm (55 mils) 0.08 mm (3 mils) 0.13 mm (5 mils) 0.38 mm (15 mils) DRAGON™ D101 - High Density 2 4 6 8 10 14 12 6 4 2 0 2 6 cm 4 0.06 mm (2.5 mils) 0.08 mm (3 mils) 0.06 mm (2.5 mils) 0.08 mm (3 mils) 0.13 mm (5 mils) 0.19 mm (7.5 mils) 16 cm EAN13 0.33 mm (13 mils) EAN13 0.33 mm (13 mils) ll-g ides com

25 50 75 100 125 200 225 cm 75 50 25 0 25 50 75 cm 150 175 0.38 mm (15 mils) 0.50 mm (20 mils) 1.00 mm (40 mils) 1.38 mm (55 mils) 1.00 mm (40 mils) 1.38 mm (55 mils) 0.25 mm (10 mils) CONNECTIONS RS232

I Leggere il codice che ripristina i default. F Lecture du code de configuration par défaut. D Lesen Sie den Restore Default Code, um die Werkseinstellung wieder herzustellen. RESTORE DEFAULT iPk iPk iPk RS232 DEFAULT SETTINGS 9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx timeout 5 sec., ack/nack protocol disabled, FIFO enabled, serial trigger lock disabled; DATA FORMAT: code identifier disabled, no field adjustment, code length not transmitted, no header, terminator = CR-LF, character replacement disabled WEDGE DEFAULT SETTINGS USA keyboard, caps lock off, num lock unchanged, inter- character and inter-code delays disabled, control character emulation = ctrl+shift+key; DATA FORMAT: code identifier disabled, no field adjustment, code length not transmitted, no header, terminator = ENTER, character replacement disabled PEN EMULATION DEFAULT SETTINGS interpret operating mode, conversion to code 39 disabled, output level normal, idle level normal, minimum output pulse 600 µs, overflow medium, inter-block delay disabled POWER SAVE sleep state disabled READING PARAMETERS trigger type = hardware, trigger signal = level, no trigger timeout, Flash On = 1 sec, Flash Off = 0.6 sec, one read per cycle, safety time 0.5 sec, beeper intensity high, tone 2, aiming spot disabled

control enabled, Puzzle Solver™ disabled, decoding safety = one read CODE SELECTION Enabled codes • EAN 8 / EAN 13 / UPC A / UPC E without ADD ON check digit transmitted, no conversions • Interleaved 2/5 check digit control and transmission, variable length code; 4-99 characters • Standard Code 39 no check digit control, variable length code; 1-99 characters • Code 128 variable length code; 1-99 characters Disabled codes EAN 128, ISBT 128, Code 93, Codabar, pharmaceutical codes, Codablock-A, Codablock-F Standard and EAN, MSI, Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49 ADVANCED FORMATTING PARAMETERS concatenation disabled, no advanced formats defined

UK Read the interface selection code for your application. I Leggere il codice per la selezione dell’interfaccia relativo al modo di comunicazione desiderato. F Lecture du code “Interface” correspondant à votre modèle. D Lesen Sie denjenigen Schnittstellen-Code, der Ihrem gewünschten Kommunikationsmodus entspricht. RS232 i$1k i$1k i$1k PEN i$1#k i$1#k i$1#k WEDGE IBM AT or PS/2 PCs i$1Bk i$1Bk i$1Bk IBM XT i$1Wk i$1Wk i$1Wk PC Notebook i$1ek i$1ek i$1ek IBM SURE1 i$1k i$1k i$1k ll-g ides com

i$1^k i$1^k i$1^k IBM Terminals 31xx, 32xx, 34xx, 37xx: UK To select the interface for these IBM Terminals, read the correct KEY TRANSMISSION code. Select the KEYBOARD TYPE if necessary (default = advanced keyboard). I Per selezionare l'interfaccia per i terminali IBM, leg- gere il codice Key Transmission appropriato e, se necessario, il codice Keyboard Type (default = advanced keyboard). F Pour selectionner l'interface pour des terminaux IBM, lire le code de transmission du clavier (Key Transmission Code) et, si nécessaire, aussi le code correspondant à votre clavier (Keyboard Type Code) (défaut = advanced keyboard). D Um die Schnittstelle für IBM Terminals einzustellen, lesen Sie den entsprechenden Key Transmission Code und falls nötig den Keyboard Type Code (Werkseinstellung = advanced keyboard). KEY TRANSMISSION make-only keyboard i$1Pk i$1Pk i$1Pk make-break keyboard i$1Ik i$1Ik i$1Ik KEYBOARD TYPE advanced keyboard i',fk i',fk i',fk typewriter keyboard i',ak i',ak i',ak

sent to the PC to be interpreted correctly independently from the Keyboard Nationality used. You do not need to make a Keyboard Nationality selection. (default = Num Lock Unchanged) Make sure the Num Lock key on your keyboard is ON. I L’impostazione del seguente tipo di interfaccia consente una corretta interpretazione dei codici a barre spediti al PC, indipendentemente dalla nazionalità della tastiera utilizzata. Non è necessario impostare la nazionalità della tastiera. (default = Num Lock Unchanged) Assicuratevi che la funzione BLOC NUM sulla Vostra tastiera sia stata attivata. F La sélection de l’interface suivante permet une interprétation correcte par le PC des codes à barres transmis, indépendamment de la nationalité du clavier. Il n’est pas necéssaire d’effectuer la sélection de la nationalité du clavier. (défaut = Num Lock Unchanged) Vérifiez que le pavé numérique soit activé sur votre clavier. D Die Einstellung der folgenden Schnittstellentypen erlaubt eine korrekte Interpretation der Strichcodes, die zum PC geschickt werden, unabhängig von der Tastaturnationalität. Es ist nicht nötig, die Tastaturnationalität einzustellen. (Werkseinstellung = Num Lock Unchanged) Bitte versichern Sie sich, daß numerische Tastaturblock aktiviert ist. IBM AT - ALT mode i$1k i$1k i$1k PC Notebook - ALT mode i$1k i$1k i$1k

i$1dk i$1dk i$1dk Digital Terminals VT2xx/VT3xx/VT4xx i$1Vk i$1Vk i$1Vk APPLE APPLE ADB Bus i$1]k i$1]k i$1]k

UK Wedge users should select one of the following WEDGE KEYBOARD NATIONALITY codes. I Quando è selezionata l’interfaccia Wedge, leggere uno dei seguenti codici per impostare la nazionalità della tastiera. F Pour l’interface Wedge, lire l'un des codes suivants pour sélectionner la nationalité du clavier. D Für den Betrieb mit einer Wedge-Schnittstelle lesen Sie einen der folgenden Codes, um die Tastaturnationalität einzustellen. English i'+ k i'+ k i'+ k Deutsch i'+k i'+k i'+k Svenskt i'+k i'+k i'+k Français i'+gk i'+gk i'+gk Italiano i'+bk i'+bk i'+bk USA i'+]k i'+]k i'+]k Español i'+k i'+k i'+k Belge i'+k i'+k i'+k

for IBM AT compatible PCs: Japanese i'+k i'+k i'+k Russian (Latin) i'+#k i'+#k i'+#k Russian (Cyrillic) i'+"Kk i'+"Kk i'+"Kk Hungarian i'+#Pk i'+#Pk i'+#Pk Yugoslavian i'+$Uk i'+$Uk i'+$Uk Romanian i'+%Zk i'+%Zk i'+%Zk Czechoslovakian i'+&_k i'+&_k i'+&_k ll-g ides com

BARCODES. To change the defaults, see the DRAGON™ Reference Manual, part number 90ACC1855. I IL LETTORE È PRONTO A LEGGERE I CODICI. Per cambiare i parametri di default, fare riferimento al manuale "DRAGON™ Reference Manual", n. d'ordine 90ACC1855. F VOTRE LECTEUR EST DÉSORMAIS PRÊT A L’EMPLOI POUR LA LECTURE DE CODES. Pour changer les paramètres voir le manuel "DRAGON™ Reference Manual" numéro d'ordre 90ACC1855. D DAS LESEGERÄT IST JETZT BEREIT CODES ZU LESEN. Um die Werkseinstellungsparameter zu ändern, schlagen Sie im Handbuch "DRAGON™ Reference Manual" nach, Bestellnummer 90ACC1855.

UK Read the TEST codes below. I Leggere i codici di test. F Lire les codes tests. D Lesen Sie die Test-Coden. EAN-8 1234 5670 EAN-13 1 234567 000992 Code 39 (Normal) 1 7 1 6 2 Code 128 t e s t Interleaved 2 of 5 0 1 2 3 4 5 6 7 8 4

Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

workmanship and materials, for a period of 24 months from the date of shipment, provided that the product is operated under normal and proper conditions. Datalogic has the faculty to repair or replace the product, these provisions do not prolong the original warranty term. The warranty does not apply to any product that has been subject to misuse, accidental damage, unauthorized repair or tampering. I Datalogic garantisce questo prodotto contro difetti di fabbricazione e di materiali per 24 mesi dalla data di consegna, a condizione che il prodotto sia utilizzato come previsto. Datalogic si riserva la facoltà di riparare o sostituire il prodotto. Quanto sopra non prolunga la garanzia originale. La garanzia non si applica a prodotti utilizzati in modo non corretto, danneggiati accidentalmente, sottoposti a riparazioni non autorizzate o manomessi. F Datalogic garantit ce produit de tout défaut de fabrication ou des matériels pendant 24 mois de la date de livraison, à condition que le produit soit utlisé correctement. Datalogic a la faculté de réparer ou de remplacer ce produit. Ces mesures ne prolongeront pas l’échéance de la garantie. La garantie ne s’applique pas aux produits qui ont été utilisés de façon incorrecte, accidentellement endommagés, soumis à des réparations non authorisées ou gâchés. D Datalogic gibt für dieses Produkt eine Garantie von 2 Jahren auf Herstellungs- und Materialfehler ab Versandsdatum, falls das Produkt unter normalen und angemessenen Bedingungen verwendet wurde. Datalogic behaltet sich vor, das Produkt entweder zu reparieren oder zu ersetzen, was aber den originalen Garantietermin nicht verlängert. Die Garantie ist nicht gültig, falls das Produkt falsch angewandt, zufällig beschädigt, unberechtigt repariert oder verändert wird.

40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DRAGON™ D101, Hand-Held Reader e tutti i suoi modelli and all its models et tous ses modèles und seine modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous: den nachstehenden angeführten Direktiven des Europäischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente: 89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi and further amendments et ses successifs amendements und späteren Abänderungen y succesivas enmiendas 73/23/EEC Low Voltage Directive Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basée sur la législation des Etates membres relative à la compatibilité électromagnétique et à la sécurité des produits. Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit entsprechen. Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas de seguridad relativas al producto. Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas: EN 55022, August 1994: LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT (ITE) EN 61000-6-2, April 1999: ELECTROMAGNETIC COMPATIBILITY (EMC). PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS. EN 60825, March 1993: RADIATION SAFETY OF LASER PRODUCTS, EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER'S GUIDE. Ruggero Cacioppo Lippo di Calderara, 21/09/2001 Quality Assurance Supervisor ll-g ides com