Cypress F2MC Series Setup Manual
Read Online
Read the Cypress F2MC Series Setup Manual online using the built-in PDF viewer.
Text of the manual
The following document contains information on Cypress products. The document has the series
name, product name, and ordering part numbering with the prefix “MB”. However, Cypress will
offer these products to new and existing customers with the series name, product name, and
ordering part number with the prefix “CY”.
How to Check the Ordering Part Number
1. Go to www.cypress.com/pcn.
2. Enter the keyword (for example, ordering part number) in the SEARCH PCNS field and click
Apply.
3. Click the corresponding title from the search results.
4. Download the Affected Parts List file, which has details of all changes
For More Information
Please contact your local sales office for additional information about Cypress products and
solutions.
About Cypress
Cypress is the leader in advanced embedded system solutions for the world's most innovative
automotive, industrial, smart home appliances, consumer electronics and medical products.
Cypress' microcontrollers, analog ICs, wireless and USB-based connectivity solutions and reliable,
high-performance memories help engineers design differentiated products and get them to market
first. Cypress is committed to providing customers with the best support and development
resources on the planet enabling them to disrupt markets by creating new product categories in
record time. To learn more, go to www.cypress.com.
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): +1.408.943.2600
www.cypress.com
F2MC Series
F2MC-8FX Starter Kit (ver. 3V)
MB2146-401-01 Setup Guide
Doc. # 002-07367 Rev. *A
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
2
Copyrights
© Cypress Semiconductor Corporation, 2005-2016. This document is the property of Cypress Semiconductor Corporation
and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or refer-
enced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United
States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as spe-
cifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property
rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with
Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable
license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code
form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organi-
zation, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resell-
ers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that
are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely
for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software
is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without fur-
ther notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in
this document. Any information provided in this document, including any sample design information or programming code, is
provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test
the functionality and safety of any application made of this information and any resulting product. Cypress products are not
designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weap-
ons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including
resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where
the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical
component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure
of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and
hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress
products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities,
including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and
Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list
of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
3
Preface
Thank you for purchasing the F2MC Series F2MC-8FX Starter Kit (ver. 3V) (Model: MB2146-401-01,
referred to as "Starter Kit" in this manual).
This product is a starter kit for F2MC-8FX MB95FV100-101 (ver. 3V), which comes with MB2146-09
(F2MC Series BGM Adapter, referred to as "BGM Adapter"), MB2146-301 (F2MC-8FX Family MCU
Board for MB95FV100-101, referred to as "MCU Board"), MB2146-401 (F2MC-8FX Family Evalua-
tion Board, referred to as "Evaluation Board"), and F2MC-8L/8FX Family SOFTUNE Professional
Pack.
This manual explains how to use the Starter Kit. Be sure to read this manual before using the prod-
uct.
For mass production/evaluation MCUs for this product, consult our Sales or Support representatives.
■
Handling and use
Handling and use of this product and notes regarding its safe use are described in the manuals for
products bundled with the Starter Kit.
Follow the instructions in the manuals to use this product.
Keep this manual at hand so that you can refer to it anytime during use of this product.
■
Caution of the products described in this document
The following precautions apply to the product described in this manual.
WARNING
Indicates a potentially hazardous situation which, if not avoided appropri-
ately, could result in death or serious injury and/or a fault in the user’s
system.
Electric shock,
Damage
Before performing any operation described in this manual, turn off all the
power supplies to the system. Performing such an operation with the
power on may cause an electric shock or device fault.
Electric shock,
Damage
Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
4
CAUTION
Indicates a potentially hazardous situation which, if not avoided appropri-
ately, may result in minor or moderate injury and/or damage to the product
or the equipment to which the product is connected, to software resources
such as data, or to other properties.
Cuts, Damage
Before moving the product, be sure to turn off all the power supplies and
unplug the cables. Watch your steps when carrying the product. Do not
use the product at an unstable location such as a place exposed to strong
vibration or a sloping surface.
Doing so may let the product fall, resulting in an injury or fault.
Cuts
The product has some sharp-pointed or edged parts inevitably exposed,
such as jumper plugs. Use meticulous care in handling the product not to
get injured with such pointed parts.
Damage
Neither put anything on or apply shock to the product. Once the product
has been powered, do not carry it. Doing either may cause a fault due to
a load or shock.
Damage
Since the product contains many electronic components, keep it away
from direct sunlight, high temperature, and high humidity to prevent con-
densation. Do not use or store the product where it is exposed to much
dust or a strong magnetic or electric field for an extended period of time.
An adverse operating or storage environment can cause a fault.
Damage
Use the product within the ranges of its general specifications.
Please see the item of “Specification” that has been described to the man-
ual of each product for the range of the specification.
Operating it outside the range of any general specification may cause a
fault.
Damage
To prevent electrostatic breakdown, do not let your finger or an object
touch any metal part of the connector. Before handling the product, touch
a metal object (such as a door knob) to discharge static electricity from
your body.
Damage
When turning the power on or off, follow the relevant procedure described
in this document. Before turning the power on, in particular, be sure to fin-
ish making all the required connections. To set up and use the product, fol-
low the instructions given in this document.
Using the product incorrectly or inappropriately may cause a fault.
Damage
Before plugging or unplugging any cable for this product, be sure to turn
the power supply off. When unplugging the cable, remove it while holding
the connector without pulling the cable itself. Pulling the cable itself or
bending it may expose or disconnect the cable core, resulting in a fault.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
5
Damage
Although the MCU socket is structured not to accept an evaluation MCU
in a wrong orientation or position, pay due attention to the mounting orien-
tation when mounting the evaluation MCU. Forcing the evaluation MCU to
be inserted in a wrong orientation can damage the pins of the evaluation
MCU and the accidental insertion prevention mechanism of the socket, re-
sulting in a fault.
Damage
When stored, the product should be kept in its packaging box as it has no
housing.
Re-transporting the product may damage it to cause a fault. Keep the
packaging materials used for shipment of the product and use them when
re-transporting it.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
1
Contents
1. Hardware Setup
2
1.1
Configuration of each product......................................................................................2
1.2
Connection of each product.........................................................................................4
2. Software Setup
8
2.1
Installation of software.................................................................................................8
2.2
Operation of SOFTUNE........................................................................................................................................ 12
3. Additional Informations
23
Revision History
24
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
2
1.
Hardware Setup
In the hardware setup procedure, you configure and connect the hardware products. This chapter
includes the configuring and connecting procedure for each product in order. Check the contents and
complete the hardware setup.
■
Configuration of each product
❐
Configuring MCU Board
❐
Configuring Evaluation Board
■
Connection of each product
❐
Connecting MCU Board and Evaluation Board
❐
Connecting BGM Adapter
❐
Connecting oscillators
❐
Connecting AC Adapter
1.1
Configuration of each product
This section describes how to configure the MCU Board and the Evaluation Board.
■
Configup-ring MCU Board
Set the following switches on the MCU Board, referring to "Figure 1-1. MCU Board Configuration".
Figure 1-1. MCU Board Configuration
BGM
ADAPTER
SUB CLOCK
C B A
1
2
CLK
CLK S.V.
APB8
C
X0
X1
X0A
X1A
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
PRODUCT SELECT
LVD4
LVD3
LVD2
LVD1
LVD0
GNDVCC
3V
5V
LVD2
OFF
LVD1
MAIN CLOCK
1 2 3 4
1 2 3 4
ON
ON
3
2
1
4
6
7
5
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
3
Hardware Setup
➀LVD2 detection voltage selection jumper plug
Set the value to "LVD0".
➁Voltage selector switch
Set the value to "3V".
➂Product selector switch
Rotate the center tab to position the pointer for the corresponding number:
For 100-pin package, set the value to "0".
For 80-pin package, set the value to "1".
For 64-pin package, set the value to "2".
For 48-pin package, set the value to "3".
For none of the above, check on the settings in the MCU Board manual.
➃LVD selector switch
Set the value to "OFF".
➄Miscellaneous switches
Set "CLK" to "OFF" if you use subclock, or "ON" if you don’t.
Set the other switches to "OFF" (to the side of numeral letters).
➅Clock input selector switch
Set all to "OFF" (to the side of numeral letters)".
➆Subclock selector jumper plug
Set all the values to the side of "B-C".
■
Configuring Evaluation Board
Set the following switches on the Evaluation Board, referring to "Figure 1-2. Evaluation Board Con-
figuration".
Figure 1-2. Evaluation Board Configuration
➀5V/3.3V Power supply selector jumper plug
Set the value to the side of "+3.3V".
➁Analog power supply jumper plug
Insert jumper plug for all the switches.
➂MOD selector jumper plug
Insert jumper plug.
SW1
JP6
JP5
JP3
JP4
1
2
119
120
1
2
119
120
CN3
JP1
JP2
CN4
PJ1
SW2
JP7
CN2
CN1
JP8
+3.3V
+5V
2
1
3
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
4
Hardware Setup
1.2
Connection of each product
This section describes how to connect the MCU Board, the Evaluation Board, and the BGM Adapter.
This section also describes how to mount the crystal oscillator on the MCU Board, and how to plug
the AC adapter into the Evaluation Board.
■
Connecting MCU Board and Evaluation Board
Connect the MCU Board and the Evaluation Board, referring to "Figure 1-3. Connection of MCU
Board and Evaluation Board". Each board has an index to avoid the reverse mounting. Look at the
index position to connect the boards.
Figure 1-3. Connection of MCU Board and Evaluation Board
SW1
JP6
JP5
1
2
119
120
1
2
119
120
CN3
JP1
JP2
CN4
PJ1
SW2
JP7
CN2
CN1
JP3
JP4
+3.3V
+5V
Evaluation Board
Index
(Backside mounting)
MCU Board
Index
(Backside mounting)
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
5
Hardware Setup
■
Connecting BGM Adapter
Connect the BGM Adapter and the MCU Board, referring to "Figure 1-4. Connection of BGM
Adapter". The BGM Adapter and the MCU Board have an index mark (for pin 1) on its connectors.
Align the index mark on both sides.
Plug a USB cable into the BGM Adapter (the cable is bundled with the BGM Adapter).
Make sure that POWER-SW on the Evaluation Board is set to OFF (to the side of "
") before
plugging the cable.
Figure 1-4. Connection of BGM Adapter
■
Connecting oscillators
Plug crystal/ceramic oscillators into the crystal oscillator mounting sockets (one for the main clock
and the other for the subclock) on the MCU Board (See "Figure 1-5. Connection of oscillators") .
You can see one crystal oscillator mounting socket for main clock and the other for subclock on the
MCU Board. Mount a crystal or ceramic oscillator and a capacitor on the MCU Board.
SW1
JP6
JP5
CN3
JP1
JP2
CN4
PJ1
SW2
JP7
MB2146-09
JP3
JP4
+3.3V
+5V
Plug into BGM Adapter
USB cable
(Bundled with BGM Adapter)
BGM Adapter
MCU Board
Evaluation Board
Power-SW
Index mark
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
6
Hardware Setup
Figure 1-5. Connection of oscillators
➀Crystal oscillator mounting socket for main clock
Mount a crystal oscillator used as "main clock".
➁Crystal oscillator mounting socket for subclock
Mount a crystal oscillator used as "subclock".
If you disable the subclock, set the "CLK" switch to "ON".
BGM
ADAPTER
SUB CLOCK
C B A
1
2
CLK
CLK S.V.
APB8
C
X0
X1
X0A
X1A
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
PRODUCT SELECT
LVD4
LVD3
LVD2
LVD1
LVD0
GNDVCC
3V
5V
LVD2
OFF
LVD1
MAIN CLOCK
1 2 3 4
1 2 3 4
ON
ON
2
1
GND
Capacitor mounting socket
Capacitor mounting socket
Crystal oscillator mounting socket
Ceramic
oscillator
Crystal
oscillator
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
7
Hardware Setup
■
Connecting AC Adapter
Connect the AC Adapter and the Evaluation Board, referring to "Figure 1-6. Connection of AC
Adapter". The AC Adapter (bundled with the Evaluation Board) is plugged into the PJ1 on Evaluation
Board and the AC 100V Power Supply.
Figure 1-6. Connection of AC Adapter
SW1
JP6
JP5
CN3
JP1
JP2
CN4
PJ1
SW2
JP7
MB2146-09
JP3
JP4
+3.3V
+5V
BGM Adapter
Plug into Evaluation Board
AC Adapter
Evaluation Board
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
8
2.
Software Setup
In the software setup procedure, you install and operate the software applications.
This chapter includes the installing and operating procedure for each software in order. Check the
contents and complete the software setup.
■
Installation of software
❐
Installing SOFTUNE
❐
Installing USB driver
❐
Installing sample program
■
Operation of SOFTUNE
❐
Starting SOFTUNE Workbench
❐
Starting Debugging
❐
Initializing MCU
❐
Running the program
❐
Aborting the program
❐
Ending Debugging
❐
Exiting SOFTUNE Workbench
2.1
Installation of software
This section describes how to install SOFTUNE and the USB driver in your host machine, as well as
how to install the sample program.
■
Installing SOFTUNE
Follow the instruction described in "F2MC-8L/8FX Family 8-bit Microcontroller SOFTUNE Workbench
Installation Guide" to install SOFTUNE in your host machine.
■
Installing USB driver
Plug a USB cable connected to BGM Adapter into your host machine. After you connect the host
machine and the BGM Adapter, the [Found New Hardware Wizard] window appears. Follow the
instruction below to install the USB driver.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
9
Software Setup
In a few seconds after the above dialog is displayed, the [Welcome to the Found New Hardware
Wizard] screen appears. Click [Next] to install the device driver.
The [Install New Hardware Device Drivers] screen appears.
Click [Search for a suitable driver for my device (recommended)], and then click [Next] to
search for a suitable driver for your device.
The [Locate Driver Files] screen appears.
Check [Specify a location], and then click [Next] to specify the location for the driver.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
10
Software Setup
A file location dialog appears.
Select "SiUSBdB.INF" in the "\Drivers" folder (under a directory where SOFTUNE is installed),
and click [Open] to specify the driver.
In the [Copy manufacturer’s files from] box, make sure that the "\Drivers" folder
(under a directory where SOFTUNE is installed) is selected, and click [OK].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
11
Software Setup
The [Driver Files Search Results] screen appears.
Click [Next] to start installing the driver.
The [Completing the Found New Hardware Wizard] screen appears.
Now that the USB driver installation has completed, click [Finish] to exit the Wizard.
■
Installing sample program
Copy only a folder named "\fsg" under "\MANUAL\FirstStepGuide" in SOFTUNE CD into the
"\sample" folder under a directory where SOFTUNE is installed.
All the data in the "\fsg" folder is set to "read-only". Open the folder’s properties, and deselect the
[Read Only] checkbox, and click [OK].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
12
Software Setup
In the [Confirm Attribute Change] dialog, check [Apply Changes to this folder, sub-folders, and
files], and click [OK] to confirm the attribute change.
Note:
This software application uses the reload timer, so it cannot be used in 48-pin package or less, which
does not implement the reload timer. When using this software, set 64-pin package or more in the
product selector switch on MCU Board.
2.2
Operation of SOFTUNE
This section describes how to start SOFTUNE Workbench and operate it using the sample program.
■
Starting SOFTUNE Workbench
Start SOFTUNE and configure the SOFTUNE development environment. From the [File] menu, click
[Open Workspace].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
13
Software Setup
In a file location dialog, select the "\sample\fsg\8fx_sample" folder under a directory where
SOFTUNE is installed, and specify "fsg_sample.wsp", then click [Open].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
14
Software Setup
Select and right-click "emu_dbg.sup" under the "Debug" folder, then click [Change Settings] to
start the setup wizard.
The setup wizard is started. Click [Next].
In [Debug Type], specify [Emulator Debugger], and click [Next].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
15
Software Setup
In [ICE Type], specify [MB2146-09], and click [Next].
In [Device Name], specify [USB], and click [Next].
In [Output Frequency], set the frequency of oscillator connected to MCU Board, and click [Next].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
16
Software Setup
The [Batch file] setting is not required. Click [Next].
Check [Auto-load when starting debug], and specify "fsg_sample.prc" in [After] under
[Specification batch file before/after load], then click [Next].
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
17
Software Setup
Check [Select All], and click [Next].
Click [Finish] to complete the setup of SOFTUNE development environment.
■
Starting Debugging
Before starting debugging, turn the Evaluation Board on. Push POWER-SW on the Board to ON (to
the side of " | ") to turn it on (See "Connecting BGM Adapter" for information about POWER-SW) .
After the Evaluation Board is turned on, click [Start debug] from the [Debug] menu to start debug-
ging.
When you start debugging, the sample program is automatically loaded.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
18
Software Setup
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
19
Software Setup
■Initializing MCU
Initialize MCU. To do so, click the Reset button on the task bar.
■
Running the program
You can run the program by clicking the "execution-related buttons" on the task bar.
You can also set a breakpoint by clicking the "
" mark in the Source window.
Reset button
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
20
Software Setup
Source window
[Execution-related buttons]
[Go]
[Step In]
[Step Over]
[Step Out]
[Run Until Cursor]
Breakpoint
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
21
Software Setup
■Aborting the program
After you have run the program, you can stop it by clicking the Abort button on the task bar.
■
Ending Debugging
To end debugging, click [End debug] from the [Debug] menu.
After you have finished debugging, turn the Evaluation Board off for safety. Push POWER-SW on the
Board to OFF (to the side of "
") to turn it off. (See "Connecting BGM Adapter" for information
about POWER-SW.)
Abort button
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
22
Software Setup
■
Exiting SOFTUNE Workbench
To exit SOFTUNE Workbench, click [Exit] from the [File] menu.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
23
3.
Additional Informations
For more informations on F2MC-8FX Starter Kit, BGM Adaptor and the MCU Board please visit our
websites:
http://www.cypress.com/documentation/development-kitsboards/mb2146-401
http://www.cypress.com/documentation/development-kitsboards/mb2146-09a-e
http://www.cypress.com/documentation/development-kitsboards/mb2146-301a-e
Please contact your local support team for any technical question.
F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide, Doc. # 002-07367 Rev. *A
24
Revision History
Document Revision History
Document Title: F2MC Series F2MC-8FX Starter Kit (ver. 3V) MB2146-401-01 Setup Guide
Document Number: 002-07367
Revision
ECN#
Issue Date
Origin of
Change
Description of Change
**
03/10/2005
HUAL
Initial release
*A
5283210 05/30/2016
HUAL
Migrated to Cypress format
