Da-Lite DESIGNER DA-TAB ELECTROL Instruction Book

3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: [email protected] POWER PRESENTATION PRODUCTS The In Instruction Book for DESIGNER DA-TAB ELECTROL®

CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by hand. 1. Carefully unpack the screen and remove the outer wrapping. 2. Always handle screen in upright position. 3. Remove the front cover of the screen from the back of the screen. Lift front cover up approximately 1/2" and pull away from back of screen. See Figure 1. 4. Remove hex head screws that secure the metal shipping brackets to the wood board. 5. Remove the Phillips head screws that attach the screen case to the wood board. 6. Remove the metal shipping brackets from the back of the slat. 7. There are two methods of mounting the screen, suspended from ceiling and wall mounted. See Figure 2. NOTE: Allow 1/2" above screen (when mounted) for front cover of screen installation and removal. 8. Picture surface is centered in case. Case extends 7" beyond surface on either end. Do not attach anything to screen slat on the bottom of the screen. PRE-INSTALLATION 1 ▲! HANGER BRACKET HANGER PIN FRONT COVER BACK OF SCREEN PICTURE SURFACE PICTURE SURFACE PICTURE SURFACE SLAT “V” BAR MOUNTED TO THE WALL WALL MOUNTING CEILING MOUNTING PLACE “D” RINGS OVER HOOKS WELL SECURED IN CEILING. FIGURE 1 FIGURE 2 INSTALLATION 1. Hang screen from wall or ceiling. FOR WALL MOUNTING HARDWARE PROVIDED 2 – “V” Bars ( one is factory mounted to the back of the case; one will be mounted to the wall) 6 – Toggle Bolts, 4" 6 – Lead Shields, #10-14 x 11/2" 6 – Phillips Flat Head Wood Screws, #10 x 2" TOOLS REQUIRED Electric Drill Masonry Bit 5/16" (if mounting in solid masonry or concrete) Screw Driver, #2 Flat Tip (if using toggle bolts) or #2 Phillips (if mounting in solid masonry or concrete) Determine the height of the top of the case from the floor. This will be the height of the wall mounted “V” bar. Hold the loose “V” bar to the wall at the height determined above (MAKE SURE IT IS LEVEL), and mark the loca- tion for the screw holes. To mount the “V” bar on solid concrete or masonry wall, drill 5/16" holes and insert the lead shields. Fasten the “V” bar to the wall using the #10 x 2" wood screws. If you are mounting to a hollow wall, drill 1/2" holes and insert the toggle bolts. Then fasten the “V” bar to the wall with the toggle bolts. Now set the case in place on the wall with the “V” bar of the case nestled into the “V” bar on the wall. FOR CEILING MOUNTING Position and properly anchor screw hooks into ceiling, beam or other solid surface. Then proceed to use the two “D” rings that are factory mounted to the top of the case to hang the case securely. 2. Install electrical hook-up that applies to your unit. Make sure to review your electrical installation checklist and wiring diagrams (included) for either 120 volt switch, 220/240 volt switch or low voltage control. See Figure 3. 3. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1 MIN. ON / 3 MIN. OFF. NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70. CEILING ALLOW A MINIMUM OF 1-1/4" FROM CEILING WALL “V” BAR MOUNTED TO THE BACK OF THE CASE AT THE FACTORY

it's necessary to adjust for more or less drop follow the steps below. The case cover must be removed to access the motor limit switches. Remove the case cover screw from both ends of the screen. See figure 4. Be sure to hold the cover while removing the screws. Rotate the cover up and away from the case until it can be removed. SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP: Turn the white limit switch screw clockwise to decrease the amount of screen drop. Run the screen down to test the stop position. If the screen drops too far, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. TO INCREASE SCREEN DROP: Turn the white limit switch screw counterclockwise to increase the amount of screen drop. Run the screen down to test the stop position. If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. SETTING THE UP LIMIT POSITION CAUTION: Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case. The screen could be damaged. SCREEN TRAVELS INTO CASE TOO FAR: Turn the black limit switch screw clockwise to decrease the amount of travel. Run the screen up to test the stop position. If the screen does not stop properly, lower the screen about one foot and turn the limit switch again. Repeat until the desired position is set. SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE: Turn the black limit switch screw counterclockwise to increase the amount of up travel. Run the screen up to test the stop position. If more travel is desired, lower the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. SCREEN ADJUSTMENT FOR 120V SCREENS ▲! DESIGNER DA-TAB ELECTROL® INSTALLATION 120V WIRING DIAGRAM UP BLACK LIMIT SWITCH KNOB TO JUNCTION BOX, MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN WHITE, BLACK AND RED LEADS. IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. OPERATING SWITCH, SWITCH BOX, AND PLATE FURNISHED WITH SCREEN. (SPDT WITH CENTER OFF) THIS SWITCH CANNOT BE USED WITH LVC. NOTE: A single switch cannot be used to operate more than one screen. Contact the factory for further information. BLACK DOWN BLACK UP RED DOWN AC HOT OFF WHITE COMMON BLACK WITH YELLOW RED UP ROCKER SWITCH AC COMMON 120 V. 50/60 HZ. 2.5 AMP. MAX DOWN WHITE LIMIT SWITCH KNOB MOTOR EXTERNAL WIRING TO BE COMPLETED BY INSTALLER. SIDE VIEW OF SWITCH AND BOX FIGURE 3

Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. If it's necessary to adjust for more or less drop follow the steps below. The case cover must be removed to access the motor limit switches. Remove the case cover screw from both ends of the screen. See figure 4. Be sure to hold the cover while removing the screws. Rotate the cover up and away from the case until it can be removed. SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP: Turn the white limit switch screw clockwise to decrease the amount of screen drop. Run the screen down to test the stop position. If the screen drops too far, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. TO INCREASE SCREEN DROP: Turn the white limit switch screw counterclockwise to increase the amount of screen drop. Run the screen down to test the stop position. If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. SETTING THE UP LIMIT POSITION CAUTION: Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case. The screen could be damaged. SCREEN TRAVELS INTO CASE TOO FAR: Turn the red limit switch screw clockwise to decrease the amount of travel. Run the screen up to test the stop position. If the screen does not stop properly, lower the screen about one foot and turn the limit switch again. Repeat until the desired position is set. SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE: Turn the red limit switch screw counterclockwise to increase the amount of up travel. Run the screen up to test the stop position. If more travel is desired, lower the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. SCREEN ADJUSTMENT FOR 220/240V SCREENS ▲! 220 / 240V WIRING DIAGRAM UP RED LIMIT SWITCH KNOB TO JUNCTION BOX, MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN BLUE, BROWN AND BLACK LEADS. NOTE: MUST BE WIRED TO CONFORM TO LOCAL WIRING CODE. THIS SWITCH CANNOT BE USED WITH L.V.C. OPERATING SWITCH, SWITCH BOX, AND PLATE FURNISHED WITH SCREEN. THIS SWITCH CANNOT BE USED WITH LVC. NOTE: A single switch cannot be used to operate more than one screen. Contact the factory for further information. DOWN WHITE LIMIT SWITCH KNOB MOTOR FIGURE 3 BLACK (UP) UP DOWN OFF BLUE (COMMON) BROWN / YELLOW ROCKER SWITCH 220 /240V. AC 50HZ. 2 AMP. MAX. BROWN (DOWN) BLUE JUMPER WIRE BLUE AC COMMON BROWN AC HOT JUNCTION BOX IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. EXTERNAL WIRING TO BE COMPLETED BY INSTALLER. REAR VIEW OF DPDT, WITH CENTER OFF.

A B 7" 7" 6" 5-1/2" A = FABRIC WIDTH + 14" B = FABRIC WIDTH 5-1/2" PICTURE SURFACE

75602 Rev. 12/08 5 TROUBLESHOOTING SYMPTOM 1. Screen will not operate. Motor does not hum. Motor hums. 2. Incorrect stopping position in downward direction. 3. Incorrect stopping position in upward direction. 4. Noise. NOTE: Screen will operate with a low pitched hum. 5. Coasting. 6. Roller displaced from mounting bracket. CAUSE (a) Incorrect line voltage. (b) Blown fuse. (c) Tripped circuit breaker. (d) No power to operating switch or junction. Power at junction box (e) Thermal overload tripped. (f) Broken wire in the “up” or ”down” position. (g) Defective motor, limit switch or capacitor. (h) Temporary binding. (i) Capacitor burned out. (a) Lost roller wrap. (b) “Down” limit switch out of adjustment (a) Lost roller wrap. (b) “Up” limit switch out of adjustment (a) Squeaking rubber end plug rubbing on motor. (b) Grinding due to foreign object in screen rubbing on roller or fabric. (c) Gear noise. (a) Defective brake. (a) Pin end slipped out of nylon bear- ing. RESTORING LOST ROLLER WRAP 1. Push strap over back of roller. 2. Tape end of strap to pocket. 3. Feed fabric as you pull strap to draw fabric over top. 4. Remove tape and strap. SOLUTION (a) Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. (b) Replace fuse. (c) Reset circuit breaker. (d) Check above. Tighten all loose wire connections. Correct any improper connections. “Down” Position Check for power across black and white leads. “Up” Position Check for power across red and white leads. (e) Let motor cool down for 15 minutes. Try again. (f) Check for continuity. Cut off old splice and reconnect. (g) Replace motor assembly. NOTE: Motor is a sealed assembly. (h) With power “off”, turn roller by hand to free binding. (i) Replace motor assembly. (a) See instructions below. (b) See installation instructions. (a) See instructions below. (b) Adjust “up” limit switch. Turn clockwise to expose more fabric. See installation instructions (a) Adjust roller to center of case. (b) Remove foreign object. (c) Replace motor assembly. (a) Replace motor assembly. (a) Remove pin end mounting. Re-align motor in tube. Re-attach pin end.