GE GE Profile 340135 Dimension Manual

GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. 340135 Specification Revised 5/09 Listed by Underwriters Laboratories JVM2052SN GE Spacemaker® Over-the-Range Microwave Oven Note: Requires 120V grounded outlet. Electrical receptacle must be located in cabinet above Spacemaker microwave oven. No additional wiring, venting or cabinet rebuilding necessary in many cases. Complete detailed, easy-to-follow installation instructions and convenient full-size templates are packed with the Spacemaker microwave oven. Important Information: When installing the Spacemaker microwave oven over a range, allow minimum of 2" from bottom of Spacemaker microwave oven to top of range backguard to allow for removal of light covers. Installation Information: This information is not intended to be used for installing unit described. Before installing, consult installation instructions packed with product/kit for current dimensional data. 66" MIN. Mounting height from floor 30" MIN. width required Exhaust outlet connects to 3-1/4" X 10" duct 16 (rear) 105° Door open 15-7/16 24-3/4 16 29-7/8 Minimum distance from door hinge side to adjacent wall should equal 1/2-inch. (without obstruction) 13" MAX. 12" MIN. Dimensions (in inches) Over-the-Range Microwave Oven Dimensions and Installation Information (in inches)

GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. 340135 Specification Revised 5/09 Listed by Underwriters Laboratories JVM2052SN GE Spacemaker® Over-the-Range Microwave Oven Hood Exhaust Duct: Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. Exhaust Connection: The hood exhaust has been designed to mate with a standard 3-1/4" x 10" rectangular duct. If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6" diameter duct Rear Exhaust: If a rear or horizontal exhaust is to be used, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust. Maximum Duct Length: For satisfactory air movement, the total duct length of 3-1/4" x 10" rectangular or 6" diameter round duct should not exceed 120 equivalent feet. Elbows, Transitions, Wall and Roof Caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent length of all transitions and adaptors plus the lengths of all straight duct sections. The chart below shows the approximate feet of equivalent length of some typical ducts. Duct Equivalent Feet A. Rectangular-To-round 5 ft. Transition Adaptor B. Wall Cap 40 ft. C. 90° Elbow 10 ft. D. 45° Elbow 5 ft. E. 90° Elbow 25 ft. F. 45° Elbow 5 ft. G. Roof Cap 24 ft. Optional Accessories (Available at additional cost) Filler Panel Kits JX52BL–Black JX52WH–White When replacing a 36" range hood, this kit fills in the additional width to provide a custom built-in appearance. For installation between ­cabinets only; not for end-of-cabinet installation. Each kit ­contains two 3"-wide filler panels. Filter KitsJX81D– Recirculating Charcoal Filter Kit To be used when the Spacemaker microwave oven cannot be vented to the outside. Dimensions and Installation Information (in inches)

Listed by Underwriters Laboratories JVM2052SN GE Spacemaker® Over-the-Range Microwave Oven JVM2052SN Time Cook Power Level Defrost Defrost Defrost Defrost Defrost Defrost Defrost Defrost Add 30 Seconds Turn Table Help Options Vent Light Light Timer Clock Clear Off Start Pause 1 2 3 4 5 6 7 8 9 0 Features and Benefits • 2.0 Cu. Ft. Capacity, 1050 Watts • Bottom Controls • Sensor Cooking Controls • Full-Width Hidden Vent • Soften/Melt Features • 1 lb. Quick Defrost •  Removable Oven Rack •  Model JVM2052DNWW – White on white •  Model JVM2052DNBB – Black on black •  Model JVM2052SNSS – Stainless steel