Wren HYPERION HYP-PP180R-B Installation Manual

www.wrensolutions.com 7L778 Rev A 200428 INSTALLATION GUIDE HYPERION PERIMETER DETECTION HYP-PP180R-B

www.wrensolutions.com 7L778 Rev A 200428 ABOUT THIS DOCUMENT This document pertains to installation of the Hyperion Perimeter Detection Unit (HYP-PP180R-B). Before installation, please familiarize yourself with this installation guide and review the Hyperion User Guide to understand system configuration and setup. PRODUCT MODIFICATIONS This product is to be installed and used for the specific purpose for which it was designed. It is not to be modified or serviced by anyone other then Wren. Unauthorized changes or modifications to the product will result in the warranty being voided and could possibly invalidate regulatory certifications. WARRANTY Unless otherwise noted, all products are covered by Wren's Standard Limited Manufacturer's Warranty as set forth in the current version of Wren's Terms and Conditions INTELLECTUAL PROPERTY RIGHTS Wren maintains certain intellectual property rights that may pertain to this product. To see a list of our patents, please refer to our TRADEMARK ACKNOWLEDGMENTS Wren®. the Wren logo, Hyperion® and the Hyperion logo are trademarks of Wren. The trademarks that are followed by ® are registered trademarks in the U.S. All other trademarks and/or registered trademarks mentioned herein are properties of their respective owners and are for reference purposes only. The use of such third party trademarks does not indicate any affiliation with or sponsorship of or by Wren. All rights reserved. NOTICES RF Exposure for FCC WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 31 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. RF Exposure for IC WARNING: To satisfy IC RF exposure requirements for mobile transmitting devices, a separation distance of 44 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. AVERTISSEMENT: Pour satisfaire IC RF exigences d’exposition pour les appareils mobiles de transmission, une distance de séparation de 44 cm ou plus doit être maintenue entre l’antenne de cet appareil et des personnes pendant le fonctionnement de l’appareil. Pour assurer la conformité, les opérations au plus près que cette distance ne sont pas recommandés. L’antenne utilisée pour cet émetteur ne doit pas être situé en conjonction avec une autre antenne ou émetteur. (800) 881-2249 PRODUCT SUPPORT For comprehensive product support including manuals, FAQs and troubleshooting, visit our customer support portal. WWW.WRENSOLUTIONS.COM /HYPERION/HYPERION-SUPPORT

www.wrensolutions.com 7L778 Rev A 200428 Prior to installation, verify that all hardware is included. If there are missing components, please contact Wren. COMPONENT LIST REQUIRED TOOLS AND ACCESSORIES #2 Phillips screwdriver Drill Cables (CAT5 or higher) IDENTIFY DEVICE MOUNTING LOCATION 1 Mounting Surface The PP180 should be mounted to a structurally solid, vertical wall surface. Mounting to a horizontal ceiling surface is not recommended and will negatively impact device performance. Mounting Height Hyperion PDU Power Supply Hyperion Radio w/ antenna

www.wrensolutions.com 7L778 Rev A 200428 IDENTIFY HYPERION RADIO MOUNTING LOCATION 2 Mounting Surface The Hyperion Radio should be mounted indoors to a structurally solid surface. When selecting a mounting location, take care to ensure that there are no obstructions, especially solid metal surfaces in the immediate vicinity of the radio and antenna. We suggest a minimum 3 foot zone surrounding the area. Mounting Height The minimum recommended mounting height for the Hyperion Radio is 10 feet from ground level. Mounting heights over or under 10 feet are acceptable but the areas must be free and clear of any obstructions. NOTE: • OBSTRUCTIONS WILL NEGATIVELY IMPACT RADIO PERFORMANCE • ENSURE THAT THERE ARE NO OBSTRUCTIONS, ESPECIALLY METAL, NEAR THE HYPERION RADIO OR ANTENNA • IT MAY BE NECESSARY TO RELOCATE THE RADIO IF PERFORMANCE /RECEPTION IS POOR.

www.wrensolutions.com 7L778 Rev A 200428 4 MOUNTING THE HYPERION RADIO 3 MOUNTING THE DEVICE Expose the mounting bracket by removing the 2 upper positioning screws and rotat- ing the housing down. Mount to the desired location using #10 size fasteners and the appropriate wall anchors (if required). Re-install the upper positioning screws. Position the device to the appropriate angle identified in Step 1. Mount to the desired location using #8 size fasteners and the appropriate wall anchors (if required). Attach the antenna to the radio and position for maximum reception. NOTE: • OBSTRUCTIONS WILL NEGATIVELY IMPACT RADIO PERFORMANCE • ENSURE THAT THERE ARE NO OBSTRUCTIONS, ESPECIALLY METAL, NEAR THE HYPERION RADIO OR ANTENNA

www.wrensolutions.com 7L778 Rev A 200428 6 RUN CABLING Cabling Specifications Maximum cabling distance is 100 feet. Cabling should be minimum CAT5 rated and at least 24AWG. Cabling Procedure Run a length of CAT5 or greater cabling from IHYP-PP180R-B to the Hyperion Radio. Crimp RJ45 connectors to each end of the ca- ble run if needed. Certify that the cabling meets the T-568A standard. 5 WALL PENETRATION PREP Drill an appropriate sized wall penetration to pass a CAT5 ethernet cable from the device to the radio.

www.wrensolutions.com 7L778 Rev A 200428 NOTE: • THESE ARE NOT ETHERNET PORTS • ENSURE THAT ALL CABLING CONNECTIONS HAVE BEEN CERTIFIED BEFORE ATTACHING TO ANY DEVICES 7 CONNECTING DEVICES 9 CONNECT POWER Use the provided power supply to apply power the radio. 8 CONNECT DEVICE DATA Connect the CAT5 cabling to the device and to the radio 10 ADD DEVICE TO THE GATEWAY The device is now powered on and ready to be added to Hyperion. Refer to the Hyperion User Manual for setup details.