Winners Only GDB166LWR Assembly Instructions

14 PCS Short (3/4") Flat Head Wood Screws 2 PCS Metal Grommet 10 PCS Long( 1-1/4") Flat Head Wood Screws 2 PCS Keys For File Drawer Lock Hardware List(included in GDB\GDE\GDT166LWR) GDB\GDE\GDT166LWRB1 Parts List LHS GLIDE PANEL BACK PANEL A C R1B PEDESTAL E D F G1 J K L M R2B PEDESTAL KEYBOARD PULLOUT CROSS BAR BACK PANEL J I L H M F B A G2 CENTER DRAWER R1 DESK TOP B 1 PC I 1 PC R2 DESK TOP GDB\GDE\GDT166LWRT Parts List RSF SIDE PANEL L-SHAPED LHS PANEL H D GDB\GDE\GDT166LWRB2 Parts List N Caution烉Please read instructions thoroughly before unpacking assembly parts. Sharp, exposed staple tips can cause injury, therefore, for your protection, please remove any exposed staples used in packing. Please keep all hardware parts out of the reach of children. 1.We recommend that you should assemble this product with the assistance of another person; this will make assembly easier, and will help to eliminate damage to the product or injury to persons during assembly. 2.Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment. 3.Please do not over tighten screws or bolts. 4.Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly purchased product correctly and efficiently. 1 PC 1 PC 1 PC 1 PC 1 PC 1 PC 1 PC 1 PC N 1 PC C Š E K RHS GLIDE PANEL L-SHAPED RHS PANEL 1 PC 1 PC 1 PC LSF SIDE PANEL G2 1 PC G1

14 13 Chart 6 Step 13. Insert the two Grommets on top of the Main Desk. Step 14. Install the Center Drawer (L) in place. Important: (Be sure to move the ball bearing retainer all the way to the front of the glide and carefully slide the rails into the glides and ball bearing retainer.) Assembly is now complete Chart 5 Step 10. Connect LHS Glide Panel (D) and RHS Glide Panel (E) to R1 Desk top (B) by slightly tightening 1-1/4" Machine Bolt (6PCS) install the Keyboard Pullout (C) in place, fasten the previously installed 1-1/4" machine Bolts (6PCS), insert 1-1/4" Flat Head Wood Screws (6PCS) to reinforce the assembly. Step 11.Connect L-Shaped LHS panel (H) to R1 Desk Top (B) and use 1-1/4" machine bolts (3PCS) and 1-1/4" flat head wood screw (2PCS) to reinforce the assembly. Step 12. Insert short (3/4") flat head wood screws (14 PCS) through metal figure 8 to connect R1 Desk Top (B) to Main Desk base and R2 Desk Top (I) to Return Desk base. X6 B 12 X14 I 12 10 10 X6 Š E D 12 L 11 X3 X2 11 11 H D E D E B B ball bearing retainer 10 C

Step 8. Loosen the screw to adjust metal figure 8 (6 PCS) of its direction of the panel and re-screw. Step 9. Align the Main Desk to the Return Desk by inserting and Fastening 1-1/4" machine bolt (4PCS) at the front and the rear side of the L-Shaped LHS panel (H). Chart 3 Step 5. Align the R2B pedestal (J) & L-Shaped RHS panel (N) to the back panel (M), and fasten with 1-1/4" machine bolts (6PCS). Step 6. Using a mallet, carefully insert Cross Bar (K) to the L-shape RHS panel (N) and R2B pedestal (J), fasten with 1-1/4" flat head wood screws (2 PCS). X6 X2 Š

Instructions: Chart 1 Step 1. Align the L-Shaped LHS panel (H) and RSF side panel (G2) to LSF side panel (G1), and fasten with 1-1/4" machine bolts (6PCS). Chart 2 Step 2. Align the R1B pedestal (A) & LSF&RSF side panel (G1&G2) to the back panel (F), and fasten with 1-1/4" machine bolts (6PCS). Step 3. Hammer the wood dowels (5 PCS) on the R1B pedestal (A) & LSF&RSF side panel(G1&G2). Step 4. Loosen the screw to adjust metal figure 8 (8 PCS) of its direction of the panel and re-screw. X8 X5 2 Š 2 2