Wen 2020 Manual 

HEAT GUN KIT bit.ly/wenvideo Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service. IMPORTANT: NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us at: 800-232-1195 [email protected] WENPRODUCTS.COM (M-F 8AM-5PM CST)

Technical Data 2 3 4 5 6 7 7 8 9 Rules for Safe Operation Specific Safety Rules For Heat Gun Electrical Information Know Your Heat Gun Operation Exploded View and Parts List Warranty TECHNICAL DATA Model number: Motor: Wattage: Cord length: Temperature: Air flow: Weight of gun: Weight of kit: 2020 120 V, 60 Hz, 6.25A/12.5A 750W (low), 1500W (high) 6 feet 572°F 1112°F 79.25GPM at 572°F 132.1GPM at 1112°F 1.5 lb 3.2 lb 2 Contents Included

Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFE- TY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain. Keep work areas well lit. 3. DO NOT use power tools in the presence of flammable liquids or gases. 4. ALWAYS keep your work area clean, uncluttered, and well lit. DO NOT work on floor surfaces that are slippery with sawdust or wax. 5. KEEP BYSTANDERS AT A SAFE DISTANCE from the work area, especially when the tool is operating. NEVER allow children or pets near the tool. 6. DO NOT FORCE THE TOOL to do a job for which it was not designed. 7. DRESS FOR SAFETY. Do not wear loose clothing, gloves, neckties, or jewelry (rings, watches, etc.) when operat- ing the tool. ALWAYS wear non-slip footwear and tie back long hair. 8. WEAR A FACE MASK OR DUST MASK. WARNING: Dust generated from certain materials can be hazardous to your health. Always oper- ate the tool in a well-ventilated area and provide for proper dust removal. Use dust collection systems whenever possible. 9. ALWAYS remove the power cord plug from the electrical outlet when making adjustments, changing parts, cleaning, or working on the tool. 10. KEEP GUARDS IN PLACE AND IN WORKING ORDER. 11. AVOID ACCIDENTAL START-UPS. Make sure the power switch is in the OFF position before plugging in the power cord. 12. REMOVE ADJUSTMENT TOOLS. Always make sure all adjustment tools are removed from the tool before turning it on. 13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. Do not leave the tool until it has come to a complete stop.

15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled foot- wear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instruc- tions for lubricating and changing accessories. 17. MAKE THE WORKSHOP CHILDPROOF. Use padlocks and master switches. 18. DO NOT operate the tool if you are under the influence of drugs, alcohol, or medication that may affect your ability to properly use the tool. 19. USE SAFETY GOGGLES AT ALL TIMES that comply with ANSI Z87.1. Normal safety glasses only have impact resistant lenses and are not designed for safety. Wear a face or dust mask when working in a dusty environ- ment. Use ear protection such as plugs or muffs during extended periods of operation. GENERAL SAFETY RULES CONTENTS INCLUDE One heat gun Shavehook scraper handle with scraper blade Four deflector nozzles

WARNING: Do not operate the heat gun until you have read and understood the following instruc- tions and the warning labels. 1. DO NOT TOUCH the end of the heat gun during or directly after operation. Let the gun cool down fully before touching the tip or any nozzles. 2. THE CARBON BRUSHES are not spark-free. Be careful during first few operations. 3. DO NOT USE A HEAT GUN near combustible or flammable materials. 4. TURN HEAT GUN OFF and give it a moment to cool down before setting it down on any surface. 5. ALWAYS use a minimum of one centimeter of distance between the nozzle and work surface. Do not press the gun against any surfaces. 6. UNPLUG the heat gun when not in use. 7. NEVER direct the air flow of the heat gun towards yourself or anyone else. 8. DO NOT LOOK into the end of the gun during or directly after operation. 9. NEVER BLOCK the inlet grill (slits on the side of the gun) or obstruct the air flow of the unit while the gun is on. 10. DO NOT STORE the tool away in the carrying case until it has fully cooled down. 11. DO NOT HOLD a work piece in front of the heat gun without forceps or clamps, as this will risk putting your hand in the pathway of the heat flow. 12. DO NOT INSERT anything in the end of the heat gun or down one of the nozzles. 13. LET THE GUN COOL DOWN before changing accessories. 14. ONLY USE THIS HEAT GUN for its intended purposes. 15. BEFORE USING THE HEAT GUN, make sure a safer means of completing your task isn’t available. 16. DO NOT DROP or use this tool to hit other objects. Do not insert sharp objects into the air inlet grill or pierce/jab internal parts.

25 ft. 50 ft. 100 ft. 150 ft. 8 A 18 gauge 16 gauge 16 gauge 14 gauge 12.5 A 16 gauge 16 gauge 14 gauge 12 gauge ELECTRICAL INFORMATION IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the outlet, have the proper outlet installed by a licensed electrician. IMPROPER CONNECTION of the equipment grounding conductor can result in electric shock. The conduc- tor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal. CHECK with a licensed electrician or service personnel if you do not completely understand the grounding instruc- tions or whether the tool is properly grounded. CAUTION: In all cases, make certain the outlet in question is properly grounded. If you are not sure, have a li- censed electrician check the outlet. WARNING: This tool is for indoor use only. Do not expose to rain or use in damp locations. Guidelines for using extension cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the correct size to be used according to cord length and nameplate ampere rating. When in doubt, use a heavier cord. The smaller the gauge number, the heavier the cord. Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp/wet areas. Use a separate electrical circuit for your tools. This circuit must not be less than a #12 wire and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the power line, make sure the switch is in the OFF position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor.

B - ON/OFF SWITCH C - AIR INLET GRILLS FOR FAN 7 KNOW YOUR HEAT GUN B C Use this versatile device for stripping paints and varnishes, thawing frozens pipes, softening adhesives for removal of linoleum and floor tile and removing stickers and labels. 1) Securely insert the plug of the heat gun into an AC 120V 60 Hz receptacle. 2) Flip the heat gun switch upward to the “1” position for a low temperature of 572°F or to the “2” position for a high temperature setting of 1112°F. 3) The heat gun stops working when the switch is pushed to position “0.” It can be safely stored in the carrying case once the unit has had some time to cool down. ­ OPERATION A

Item Stock # Description 1 2020-001 Left side housing 2 2020-002 Mica paper 3 2020-003 Steel sleeve 4 2020-004 Locating ring 5 2020-005 Front cover 6 2020-006 Heat coil set 7 2020-007 Heat insulation ring 8 2020-008 Fan cover 9 2020-009 Screw 10 2020-010 Fan 11 2020-011 Screw 12 2020-012 Motor base Item Stock # Description 13 2020-013 Motor 14 2020-014 Diode 15 2020-015 Trigger 16 2020-016 Switch 17 2020-017 Terminal 18 2020-018 Cable clip 19 2020-019 Cable guard 20 2020-020 Screw 21 2020-021 Right side housing 22 2020-022 Screw 23 2020-023 Screw 24 2020-024 Cable

this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN con- sumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase. Ninety days for all WEN products, if the tool is used for professional use. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons other than Seller or Authorized Service Center. To make a claim under this Limited Warranty, you must make sure to keep a copy of your proof of purchase that clearly defines the Date of Purchase (month and year) and the Place of Purchase. Place of purchase must be a direct vendor of Great Lakes Technologies, LLC. Third party vendors such as garage sales, pawn shops, resale shops, or any other secondhand merchant void the warranty included with this product. Contact [email protected] or 1-800-232- 1195 to make arrangements for repairs and transportation. When returning a product for warranty service, the shipping charges must be prepaid by the purchaser. The prod- uct must be shipped in its original container (or an equivalent), properly packed to withstand the hazards of ship- ment. The product must be fully insured with a copy of the warranty card and/or the proof of purchase enclosed. There must also be a description of the problem in order to help our repairs department diagnose and fix the issue. Repairs will be made and the product will be returned and shipped back to the purchaser at no charge. THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS THAT WEAR OUT FROM REGULAR USAGE OVER TIME INCLUDING BELTS, BRUSHES, BLADES, ETC. ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO TWO (2) YEARS FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT AL- LOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITA- TION MAY NOT APPLY TO YOU. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAM- AGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CON- SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY. THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE ELECTRIC TOOLS, BENCH POW- ER TOOLS, OUTDOOR POWER EQUIPMENT AND PNEUMATIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT THE WEN CUSTOMER SUP- PORT LINE. LIMITED TWO YEARS WARRANTY