WAFER GSM-DKEY Manual 

http://www.waferstar.com GSM-DKEY MANUAL SHANGHAI WAFER MICROELECTRONICS CO.,LTD

http://www.waferstar.com GSM-DKEY OPERATING INSTRUCTIONS PRODUCT DESCRIPTION WAFER GSM-DKEY is an electronic board with an on-board GSM modem support Double SIM card.The purpose of this device is to open the electric gates by means of a GSM phone.It has two door open relay whose contact has to be connected in parallel with the button which opens the gate. It has a White List of numbers who are enabled to control the device up to 200. When the GSM-DKEY receives a call, it will check to see if the calling number is in the list. If it is in the list it will reject the call (so there will be no charge -at least with today's charging procedures) and click the relay momentarily. Also GSM-DKEY has two alarm input port for the security detection including the intruder detection alarm and gate problem alarm. CONNECTOR DESCRIPTION (For USB version,only the program port from serial to USB port) ADVANTAGES OF WAFER GSM-DKEY ˇ 200 Number memory. ˇ Different SIM card number for different relay output ˇ No call charges to operate. ˇ No line rental using ‘Pay as You Go’. ˇ No key-fobs for children to lose. ˇ Open gates prior to arriving. ˇ Let visitors and deliveries in remotely. ˇ Impossible to clone or intercept. ˇ Caller ID confirmation for security. ˇ Quick & easy number barring. ˇ Can be operated from anywhere. ˇ Easy programming in minutes with your phone or PC software 1. GSM LED (Left) 2. MCU LED (Middle) 3. RELAY LED (Right)

http://www.waferstar.com INSTALLATION To install the GSM-DKEY, you need to connect the 2 wires of the relay contact in parallel with the gate opening button. The relay contacts can stand 48V 0.5A maximum, this is enough for its operation but don't try to switch higher voltages or currents. You should install the GSM-DKEY in a place where there is GSM signal coming from the operator you want to use. Check it with a phone before proceeding with the installation. If you need to install the device in a place with little signal, you may consider using an external antenna that we may supply as an option to be purchased separately with 50cm cable. You should then insert the SIM Card of the operator you want to use with the right direction according to the following pictures. !Note! : You must remove the PIN request from the SIM before inserting it in the unit, otherwise the device will not work. In order to do so, insert the SIM in a phone and disable the PIN request (usually there is a security menu that enables you to do so). Please read this entire manual before installation !Note!  Take EXTREME care with the high voltage AC220V Power line installation  In case of fault pull the mains adapter out from 220V network immediately.  If device is connect into electricity, you couldn’t take off its cover.  To maximise reception, install the GSM antenna in a prominent elevated position if possible, and vertically mounted.  The GSM unit requires mounting carefully in a weatherproof enclosure for out door operation.  Always ensure that the power is switched OFF before inserting or removing a SIM card from its holder or damage will be caused to the module. 1.Slide back the SIM door and lift it up 2.Slide the SIM Card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder 3.Close the SIM door 4.Slide the SIM door to lock the SIM card in place

http://www.waferstar.com GSM-DKEY also comes with additional 2 Input.The inputs can be used to generate alarms when triggered.For examples,you can can connect the saftey beam output to the GSM-DKEY Alarm1 and Alarm2 input. WAFER GSM-DKEY PROGRAMMING You can program the GSM-DKEY with SMS commands using your phone. It is safe to do so because in addition to the fact that other people may not know the number of the SIM inserted in it, we also use a Password that makes it impossible for anybody who doesn't know it to access the system by chance. Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap etc. Don't add spaces or any other character. Some complicated Instructions,that cann’t be programmed by the phone SMS. That would need to use the PC software to program and inquire the status of the terminal. The bellow wire picture is to show how to connect the cable to the PC program connector with the Program adapter.Please connect it in the right direction with the picture. On board,we have designed a Five pin DIP Switch 1. MODE: When “ON” postion at MODE0 and “OFF” for MODE1 2. ALARM: When “ON” postion, Alarm is On 3. ACM: When “ON” position, ACM is On 4. REPORT: When “ON” position, REPORT is enable 5. REPLY: Not available Only when the hardware is OFF,then can use the software to do the enable or disable The following compand is used in the GSM-DKEY : #PWD: Password #CAP: Change password #WHL: White List (add or remove numbers) #GOT: Gate pulse time #ACM: ACM is used for free control or security control #ALARM: Alarm information setting #MODE: Relay mode #CSQ: Check Signal Quality #SCA: Set service center address #STATUS: Check status Once you issue a command with an SMS, you will receive a confirmation SMS with OK if everything is correct or Err if there is an Error.

http://www.waferstar.com GSM-DKEY SMS COMMAND LIST: #PWD Password. This command must always come first 6 digits as a password. The standard default one, when the device comes from the factory, is 123456. We suggest that you change it, using the #CAP command. In all the following examples we will use 123456 as an example of password. #CAP Change Password. Use this command to change the password with a new one that you will chose for your device ( don't forget it or you will have to send the unit back to us to reset it, and this has a cost ) The #CAP command must be issued 2 times to be sure you don't digit a wrong one. OF course it must be preceded by the old password. For example, to change the password 123456 into the new password 333444 you need to send the following SMS: #PWD123456#CAP333444#CAP333444 Acknowledge SMS: PWD SETUP OK If you wrote correctly, or an Error message if you made a mistake. If the old password is error,then conformation would be : Error Old Password If you input two different new password,then reply would be : Error New Password,Please Check the input again #WHL White List. This is the command that you will use most. it is used to add or remove numbers that are enabled to open the gate into the White List. You can add up to 200 numbers in the list. Every position must be indicated in the command and we advise you to keep a list written somewhere to know which numbers are in and in which position. • To add a number, the syntax of the command is the following: #PWD123456#WHL01=61143815 Acknowledge would be : WHL01 SET TO 61143815 OK Where 01 is the position in the list and 61143815 is the number enabled. Please note that it is possible to program up to a maximum of 10 digits for a number. If it has more digits you should use the rightmost ones. For example, if your number is 33446665555 you should program 3446665555. If your number appears as +85261143815 you should not program the country code (+852). If your number has only 9 digits or less, it is not a problem. The important thing is that you don't exceed 10 digits. • To check which is the number in a place of the list: #PWD123456#WHL01? Acknowledge : WHL01 IS 61143815 OK • To erase a number: #PWD123456#WHL01=0000000 (or you can write over it another number you wish to add)

http://www.waferstar.com Acknowledge : WHL01 SET TO 00000000 List All numbers in the List #PWD123456#WHL=ALL? (PC) Acknowledge : WHL01 IS XXX WHL03 IS XXX WHL08 IS XXX …… #SHL, #PHL, #QHL Special List. Set from what time to what time you want these numbers operate #PWD123456#SHL001=13564121668:1357(8:32-23:59) Acknowledge : SHL001 SETUP TO 61143815:1357(8:32-23:59) ### SHL001 number would operate from 8:32 to 23:59 in Mon,Wen,Fri,Sun in every week. Set from date to date you want these numbers operate #PWD123456#PHL001=13564121668:100324-101012(8:32-18:26) Acknowledge : PHL002 SETUP TO 61143816: 100324-100812(8:32-18:26) ### PHL001 number would operate from 8:32 to 18:26 from Mar.24th to Oct.12 #PWD123456#QHL001=13564121668:12 Acknowledge : QHL003 SETUP TO 61143817:12 ### QHL001 number would operate total 12 times,then would be expired. • To check which is the number in a place of the list: #PWD123456#SHL0001? Acknowledge : SHL01 IS 61143815 OK Or #PWD123456#PHL0001? #PWD123456#QHL0001? • To erase a number: #PWD123456#WHL01=0000 Or #PWD123456#PHL01=0000 #PWD123456#QHL01=0000 (or you can write over it another number you wish to add) List All numbers in the List #PWD123456#SHL=ALL? (Instruction Only for PC) Acknowledge : SHL01 IS XXX SHL03 IS XXX QHL08 IS XXX …… #QUERY Query the phone number in the WHL list. (PC$PHONE) Query the phone number in the position of the WHL list,Special phone list or Alarm phone list #PWD123456#QUERY=143535353 (PC$PHONE) Acknowledge: QUERY RESULT: 143535353 AT WHL004

http://www.waferstar.com #ACM Safety control or free control mode setting. (PC$PHONE) #PWD123456#ACM=ON #PWD123456#ACM=OFF ACM=OFF, Then any number can free control the device through the phone calling ACM=ON, Then only the authorized number can control the device through the phone calling #GOT Relay working output delay time. (PC$PHONE)(Only for NO.1 Relay) When setup the GOT Timer,firstly you also need to setup the timer multiplier at millisecond or second or minutes. #PWD123456#TIMER-DELAY-AT-MILLISECOND #PWD123456#TIMER-DELAY-AT-SECOND #PWD123456#TIMER-DELAY-AT-MINUTE And then we need to do the following setting for GOT timer for each relay output: #PWD123456#GOT1=12 #PWD123456#GOT2=05 This command is useful in case you need to keep the Relay output working longer. The standard time is 5 seconds (5000 ms). You can change it with the GOT command. With the above command the delay time has been set to 5000 ms (5 seconds). You can check what the current relay output delay time is with the command #PWD123456#GOT? (PC$PHONE) Acknowledge: GOT1=05S,GOT2=052999S #ALARM Alarm setup (1)You can setup the alarm phone number when have the alarm information input #PWD123456#ALARM01=13818120592 (PC$PHONE) Where 01 is the position in the list Acknowledge: ALARM01 SET TO 61143815 OK When the number is seted to 000000,that means delete the number in this position (2) check which is the number in a place of the alarm phone list: #PWD123456#ALARM01? (PC$PHONE) Acknowledge: ALARM01 IS 61143815 OK (3) List all numbers in the alarm phone list: #PWD123456#ALARM=ALL? (PC$PHONE) Acknowledge: ALARM IS XXXXX:XXXX:XXXXXXX:0000:0000 (Will show total five numbers, if no effective number,that will be replaced with 0000 ) (4) Alarm mode setup (PC$PHONE) There are two alarm input ,you can set at PHONE or SMS #PWD123456#ALARM-IN1=ON:PHONE:10,ALARM-IN2=OFF （PC$PHONE） Acknowledge: ALARM_IN1=ON:PHONE:10,ALARM_IN2=OFF OKAY #PWD123456#ALARM-IN1=ON:SMS:300,ALARM-IN2=ON:PHONE:10 （PC$PHONE） Acknowledge: ALARM_IN1=ON:SMS:300, ALARM_IN2=ON:PHONE:10 If at phone mode: when receive the alarm input,then will phone the number in the alarm phone list until you reject the phone call or that will continue to phone the number again after the minutes setted.

http://www.waferstar.com If at SMS mode: When receive the alarm input,then will send the SMS to the number in the alarm phone list until you send the SMS to PAUSE the alarm . (5) Config the SMS TEXT : (PC) #PWD123456#UDI1:XXXXXX,UDI2:XXXXXX Acknowledge: UDI1:XXXXXX,DI2:XXXXXX OKAY (When the Alarm input is triggered,then will send the SMS you already setted with this UDI command) Check the text set #PWD123456#UDI? Acknowledge: UDI1:ABC1, UDI2:ABC2 #REPORT Report the system status change (PC$PHONE) When setup to: #PWD123456#REPORT=ON Then any device status change would send the alarm SMS to Alarm01 number #PWD123456#REPORT=OFF No report for the device status change #CSQ Check GSM signal quality. (PC$PHONE) This command is useful to see what is the GSM network signal level your GSM-DKEY is receiving. It ranges from 0 to 32 (if it is 0 we doubt it will ever answer...). You should have a signal above 12 to be sure of being able to open the gate in any condition. Better if above 16. You should add an external antenna if this is not the case, or eventually even change operator with another that serves your area better. #PWD123456#CSQ? Acknowledge: CSQ IS 26 #MODE Relay1 and Relay2 Operation Mode SETUP (PC$PHONE) #PWD123456#RELAY1=MODE0 ( or #PWD123456#RELAY2=MODE0 ) Acknowledge: RELAY1 SET TO MODE0 #PWD123456#RELAY1=MODE1 ( or #PWD123456#RELAY2=MODE1 ) Acknowledge: RELAY SET TO MODE1 If set to MODE0,that is Momentary pulse and If Config to MODE1,that is Ratchet relay #STATUS Check the config information of the terminal (PC$PHONE) #PWD123456#STATUS? You will receive a Acknowledge with: ALARM1=ON:SMS:02,ALARM2=OFF:SMS:5,GOT=05S,WHL=01,ALARM1=HIGH,ALARM 2=HIGH,BCPW=00,CSQ=10,RELAY1=ON,RELAY2=OFF #OUT Control the Relay Output on or off (PC$PHONE) #PWD123456#OUT1=ON or OFF You will receive the following confirmation SMS: OUT1 ON OK or OUT1 OFF OK

http://www.waferstar.com #PWD123456#OUT2=ON or OFF (If has the second relay output on board) You will receive the following confirmation SMS: OUT2 ON OK or OUT2 OFF OK #RLY Toggle the Relay temporarily ON or OFF for specified timer (PC$PHONE) #PWD123456#RLY1=5 You will receive the following confirmation SMS: #RLY1-ON: 05 #PWD123456#RLY2=12 You will receive the following confirmation SMS: #RLY2-ON: 12 Config the RELAY Status when power Reset again #PWD123456#POWER-RESET=11 (1 means ON ,0 means OFF when power on) You will receive the following similar confirmation from the unit POWER-RESET OK #PWD123456#POWER-SAVE You will receive the following similar confirmation from the unit POWER-SAVE OK

http://www.waferstar.com Troubleshooting No LED is on after power up · Check the power supply. GSM LED is not flash slowly · GSM Signal is not good and cann’t register to GSM · Check the SIM card. · Check the PIN. · Check the antenna connection. · Select a place with a good GSM signal. MCU LED is not flash slowly · MCU is not working properly,Check the syster power No tone can be heard after line off-hook · Check the telephone line connection. · GSM-DKEY is not initialized properly upon start (approx. 10s after power up). · GSM-DKEY is not supplied with power. EasyGate does not communicate with PC · Check the serial cable connection. · Check the COM number setting on PC. · Check the COM parameters (1200-115200 bps, 8N1). · An incoming call is ringing on GSM-DKEY · An incoming Alarm is on processing by GSM-DKEY

http://www.waferstar.com This brochure provides an overview of the products and services of WEIFU GSM Modules, For further information and queries kindly contact: Email: [email protected] Web: www.waferstar.com Tel: 0086-21-51870528 Also accessible via our online MSN service: [email protected] Copyright 2008, WEFU GSM V2009-V2.1