Volt VPL-3024-BBZ Installation Instructions Manual

VOLT® Elevator Path & Area Light VPL-3024-BBZ INSTALLATION INSTRUCTIONS Specifications and product details subject to change without notice. © Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. [email protected] • 813.978.3700 - 1 - Help Hotline: 1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST) all-guide s.com

VPL-3024-BBZ Important: Please Read Before Installation INSTALLATION INSTRUCTIONS ! w w w . v o l t l i g h t i n g . c o m - 2 - This fixture is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty. These instructions do not intend to cover all variations in installation, operation maintenance or mounting situation. 1.  Make sure that the power is turned OFF before installing or servicing this fixture. 2.  Warning: this fixture is not intended to be installed within 10 feet [3 meters] of a pool, spa or fountain. 3.  This fixture is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. 4.  Underground Low Energy Cable must not be buried over 6” (15.2 cm) in order to connect to the main low voltage cable. 5.  Wiring connections must be made with wire connectors that are suitable for outdoor use. 6.  Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting. Important Safety Instructions ! LIGHTED LAMP IS HOT! WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS. 1.  Turn off/unplug and allow to cool before reducing lamp. 2.  Lamp gets HOT quickly! 3.  Do not touch the hot lens, guard or cowl. 4.  Keep lamp away from materials that may burn. 5.  Do not touch lamp at any time. 6.  Use a soft cloth. 7.  Oil from skin may damage lamp. 8.  Do not operate the fixture with a damaged or missing lens or shield.

Package Contents A.  (1) Fixture Body B.  (1) Extension Pole C.  (1) Stake Parts Required (sold separately) A.  (1) LED Lamp Product Dimensions 24.5” 2.5” 4” 2” - 3 -

VPL-3024-BBZ Remove Faceplate Install/Replace Lamp 1 2 Unscrew the faceplate, then remove it from the fixture body. Insert the lamp with the correct wattage and type marked on the fixture label. CAUTION: Do not exceed maximum wattage marked on luminaire label. NOTE: DO NOT touch lamp with bare hands. Use soft cloth to handle lamp. NOTE: The “Wafer” Bi-Pin LED lamp also can be used in this fixture. Fixture Body Faceplate Socket Lamp w w w . v o l t l i g h t i n g . c o m - 4 - “Wafer” Bi-pin LED Lamp

Install Faceplate 3 Screw the Faceplate back onto the fixture body. Hand tighten until snug. Faceplate Fixture Body - 5 -

VPL-3024-BBZ w w w . v o l t l i g h t i n g . c o m - 6 - Install Fixture to Stake 5 Fixture Pigtail Wireway Slot Stake Install Stake 4 Board Stake Soil Ground Clear away an area on the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and thread the fixture onto the stake. Tighten until snug using the lock nut to secure it to the base. Determine the desired location for mounting the fixture. Hammer the stake into the ground until the flange of the stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering. NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel. all-guide s.com

Wire Connections 6 Pigtail Main Supply Cable Wire Connectors - 7 - Strip both leads from the luminaire pigtail. Using two wire connectors (sold seperately), connect the leads from the luminaire to the main supply cable leads.

© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. [email protected] • 813.978.3700 w w w . v o l t l i g h t i n g . c o m - 8 -