Vitek Transcendent Series Quick Start Manual

available online. Scan the QR Code or visit: http://www.vitekcctv.com/Downloads VTD-TND6FP Transcendent Series 6 Megapixel H.265 IP Vandal 360° Fisheye Camera w/6 IR LEDs QUICK START GUIDE FEATURES • 1/2.9” 6.0 MegaPixel CMOS Image Sensor • Up to 30fps live view @ 6 MegaPixel • Multiple Views: 360° Overview, Double 180° Panorama View, Overview + 3 Views, and Single View • 1.07mm @ F2.5 Fisheye Lens with 180° horizontal field of view (wall mounted) / 360° (ceiling mounted) • 6 High Power Covert IR LEDs with 50’ IR Range • True Mechanical Day/Night function by ICR • XD-DNR (2D-DNR & 3D-DNR) Noise Reduction • ROI Encoding • H.265/H.264/MJPEG Triple Streaming • Secondary Video Output (CVBS) • Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps • ONVIF Compliant • MicroSD memory card slot for Local recording supporting up to 128GB MicroSDXC cards • IK10 Impact Resistance Rating • Two Way Audio • 12VDC & PoE (Power over Ethernet) Operation all-guide s.com

Camera Quick Guide Screws Hex Wrench Drill Template Plastic Wall Anchors Waterproof Cap RJ-45 Ethernet Audio In Audio Out CVBS Output Alarm I/O RS-485 Power Cable MicroSD Card Slot Reset 1 2 3 4 5 6 7 8 9 1 3 4 5 6 7 2 8 9

First connect the Waterproof Cap to an Ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC Power Supply. Weather Resistant Network Coupler 1. Loosen the nut from the Weather Resistant Network Coupler, 2. Run ethernet cable through coupler, then attach a RJ-45 connector. 3. Tighten the nut and coupler for a weather resistant seal. ALM-COM ALM-OPEN ALM-INA ALM-GND RS485T+ RS485T- 12VDC Optional 12VDC Power Connection. Not needed with PoE

Gap Fixed Ring 1. Remove the fixed ring from the camera. 2. Loosen the screws of the cover of the SD card and then insert the SD card. Then reinstall the cover ring.

strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows: 1. Remove the fixed ring from the gap of the camera (see Install SD Card) 2. Drill the screw holes and the cable hole on the wall according to the drill template. 3. Route and connect the cables. 4. Fix the camera to the wall with screws as shown. 5. Install the fixed ring back onto the camera. ∅5.12” ∅0.18” 3.31” 3.82”

IP-Tool or directly in a web browser. Accessing the Camera Using the IP-Tool 1. Make sure the camera and PC are connected to the LAN. 2. Locate the IP-Tool installer on the included Product Documentation CD, then install on the PC. Open the installed application. 3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation. For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting. ** Default admin password: “123456". all-guide s.com

browser to connect IP-CAM . IE browser will download the Active X control automatically. After downloading, a login window will pop up as shown below: Input the user name and password to log in. Default user name: admin / Default password: 123456. Directly Access Through a Web Browser The default network settings are as shown below: IP address: 192.168.226.201 HTTP: 80 Subnet Mask: 255.255.255.0 Data Port: 9008 Gateway: 192.168.226.1 You may use the above default settings when you log in the camera for the first time. 1. Manually set the IP address of the PC and the network segment should be as the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window. Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

confirm. The IE browser will download Active X control automatical- ly. 3. After downloading Active X control, the login dialog box will pop up. 4. Input the default username and password and then enter to view. WAN Configuration Access the camera by the router or virtual server for example. 1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig→Network Config→Port menu to set up the port number. 2. Enter System Config→Network Config→IP Address menu to modify the IP address. 4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM. 3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.

TRANSCENDENT IP CAMERAS INTRODUCING OUR NEW INTRODUCING OUR NEW VT-TNR3216PF VT-TNR818PF VT-TNR1646PF • 8MP (4K) HDMI Output • H.265 / H.264 Compression • Full Analytic Support Including Face Detection • 360 Degree / Fisheye De-Warping • Available in 8, 16, and 32 Channels • Up to 80TB Depending on Model • PoE Support on ALL Models ADVANCED LEARNING NVRs A Standalone Solution with FULL Analytic Support

Transcendent VTD-TND6FP Fisheye Dome Camera VT-TWM-F Wall Mount for Transcendent VTD-TND6FP Fisheye Dome Camera VT-TPDM-F Pedestal Mount for Transcendent VTD-TND6FP Fisheye Dome Camera all-guide s.com

WWW.VITEKCCTV.COM Version 1.0 June 2018 LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller. The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning. The product must not have been tampered with in any way or the guarantee will be considered null and void. This guarantee does not affect your statutory rights. Contact your local VITEK Reseller should servicing become necessary. VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller. June 2020 Version 1.1