United Technologies Interlogix AdvisorOne Installation Sheet

1 / 3 AdvisorOne Battery Installation Sheet EN CNF ES PR 1. Battery 2. Battery Location English: Installation Sheet Description The Advisor™One self-contained lifestyle management and security system detects situations and provides control and information to home and small business owners (P/N AVO-1037). This document provides instructions on replacing the rechargeable 7.2 VDC, 2800 mAh NIMH backup battery (P/N AVO-BAT28A) for use with the AdvisorOne panel. It is recommended that the backup battery be replaced every 3-5 years or as needed. Preparation and Installation Preparing to Install the Battery WARNING: Use caution when installing or removing the 20JUN14power supply to an outlet with a metal cover. 1. Depending on the situation, it may be necessary to contact the central monitoring station before starting the installation. 2. If a power supply is present, remove the screw from the securement tab and unplug the power supply. 3. Remove the screw securing the panel chassis. Open the panel by pressing down on the tabs and carefully swing the panel chassis open. CAUTION: Use static electricity precautions when handling electronic components.

AdvisorOne Battery Installation Sheet 4. If a battery (A in Figures 1 and 2) is not installed, proceed to “Installing the Battery”. If a battery is currently installed, release the battery strap (F in Figure 2). Disconnect the battery from the battery connector (D in Figures 1 and 2) by pressing down on the wire end of the battery clip (E in Figure 1). Remove the existing battery. Note: Do not dispose of the old battery until the new battery has been installed, tested and is functional. Once the new battery is tested and is functional, dispose of the old battery in accordance with local regulations. Installing the Battery 1. Place the battery in the battery compartment with the wires (B in Figures 1 and 2) facing up as shown. Position the battery so that the tape (C in Figures 1 and 2) is near the battery connector (D in Figure 2). Secure the battery in position with the battery strap (F in Figure 2). 2. Route the battery wires (B in Figures 1 and 2) to the battery connector (D in Figure 2) and place the excess cable in the open area next to the battery. Do not connect the battery to the battery connector on the panel until step 4. 3. Supply power to the panel as noted in Table 1. Table 1: Powering the Panel Installation Action Note US Plug the power supply into the outlet and secure with the supplied screw. Canada Plug the power supply into the outlet. Do not use the securement tab and screw. All Other Installations Follow regional requirements. Note: Connect the battery within 15 seconds of providing power from the power supply to reduce the potential for a low battery indication. 4. Connect the battery to the battery connector on the panel (D in Figure 2). Note that the cable connector (E in Figure 1) locks in place. 5. Close the panel, making sure all tabs are engaged. Replace the screw securing the panel chassis. 6. If the central monitoring station was notified, inform them that this operation is complete. Upon initial installation, the battery may take up to 48 hours to be fully charged. If the battery is low, a Low Battery icon will be present and trouble beeps will sound until the battery is sufficiently charged. After the initial charge, should the panel lose power from the power supply and experience a low battery condition, the icon will appear and trouble beeps will sound unless silenced. Battery Configuration and Programming To confirm the battery is supplying power to the panel: 1. Press the System Status icon . 2. Verify the Battery icon is displayed in the System Status. If the Battery icon is not displayed, see the “Troubleshooting” section. Battery Configuration At installation, the battery may not be fully charged. To check the battery status, press the System Status icon . To test the battery: 1. Press the Settings icon on the lower left of the main screen. 2. Press CONFIGURATION to enter programming. 3. Enter installer code or dealer code. 4. From the Configuration & Programming screen press TEST. 5. From the Test screen press BATTERY. 6. To start the battery test, press START. The results will be displayed after the battery test is complete. Programming No programming is required.

3 / 3 Troubleshooting The Battery Connector Will Not Plug into the Board Connector • Battery connection is keyed. Slide the clip on the battery connector over the catch (or lock) on the board connector. • Ensure there is a secure connection. The Status Attention Icon Appears and the Panel Indicates a Battery Fault • Verify the battery is connected correctly. • Check the battery status as noted in the “Battery Configuration” section. • If a persistent low battery indication continues for about a week, this may indicate a bad battery. Replace the battery. Specifications Dimensions 1.4” wide x 1.3” high x 4.1” deep (35 mm x 32 mm x 105 mm) Power rating Rechargeable battery: 7.2 VDC, 2800 mAh NIMH Storage temperature 14 to 86 ºF (-10 to 30ºC) 90 days shelf life Operating temperature 32 to 122ºF (0 to 49ºC) Compatibility AdvisorOne panel Contact Information For general information, see www.interlogix.com. For customer/technical support, see www.interlogix.com/customer-support or call +1 855 286 8889. © 2014 United Technologies Corporation. Interlogix is part of UTC Building and Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Limitation of Liability To the maximum extent permitted by applicable law, in no event will Interlogix be liable for any lost profits or business opportunities, loss of use, business interruption, loss of data, or any other indirect, special, incidental, or consequential damages under any theory of liability, whether based in contract, tort, negligence, product liability, or otherwise. Because some jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages the preceding limitation may not apply to you. In any event the total liability of Interlogix shall not exceed the purchase price of the product. The foregoing limitation will apply to the maximum extent permitted by applicable law, regardless of whether Interlogix has been advised of the possibility of such damages and regardless of whether any remedy fails of its essential purpose. Installation in accordance with this manual, applicable codes, and the instructions of the authority having jurisdiction is mandatory. While every precaution has been taken during the preparation of this manual to ensure the accuracy of its contents, Interlogix assumes no responsibility for errors or omissions. Canadian French: Installation Sheet Translation of the manual into Canadian French. Spanish: Installation Sheet Translation of the manual into Spanish. Portuguese: Installation Sheet Translation of the manual into Portuguese.