Tyco Electronics CPC 45 Series Instruction Sheet
Read Online
Read the Tyco Electronics CPC 45 Series Instruction Sheet online using the built-in PDF viewer.
Text of the manual
(.#1)". )"/0(# ,++%#0,. %.(%/
+/'(%)$%$ "// '.,1&' %#%-0"#)% (0
6-
$>*6 3,*:8650*9 68768(:065 (8809);8. !
33 5:,85(:065(3 "0./:9 ",9,8<,+
$ 36.6 (5+ $>*6 3,*:8650*9 (8, :8(+,4(829
$8(+,4(82 :/,8 786+;*:9 36.69 (5+ *647(5> 5(4,9 ;9,+ (8, :/, 7867,8:> 6- :/,08 8,97,*:0<, 6=5,89
$ ###$ $"
!" %$ " $
$/09 *65:8633,+ +6*;4,5: 09 9;)1,*: :6 */(5.,
68 3(:,9: 8,<09065 (5+ ",.065(3 ;9:64,8 #,8<0*,
<090: 6;8 =,)90:, (: 22203#,%)%#0.,+(#/#,*
%
",<
Figure 1
& ("
&
*- &
,, ' &2
($(
).*& +
6*205.
$()
3(5.,
6;5:05. 63,
!3(*,9
CPC Series 45 Unshielded Pass–Through Receptacle
Kit 1776186–1 is designed for use in harsh
environments. The receptacle engages with CPC
shielded or unshielded plugs.
This receptacle kit is designed for front or rear
panel–mount applications.
(,-+. -$)( ,# -
*+)/$ , ,, ' &2
( (" " ' (- $(,-+. -$)(, !)+ -# *&.",
$' (,$)(, $( -#$, $(,-+. -$)( ,# - + $( ' -+$
.($-, 0$-# .,-)' +2 .($-, $( + % -,
$".+ , + ()- + 0( -) , &
Reasons for reissue of this instruction sheet are
provided in Section 5, REVISION SUMMARY.
This receptacle kit consists of the components shown
in Figure 1.
!
1. Align the locking tab of the coupler (mating face
first) with the wide slot at the back (large diameter
end) of the receptacle assembly. Depress the
locking tab, and insert the coupler into the
receptacle assembly until there is an audible
“click.” See Figure 2, Detail A.
2. Fit the flange seal over the mating face (small
diameter end) of the receptacle assembly (for back
panel mount) or the back of the receptacle
assembly (for front panel mount) until it is flat
against the flange. Make sure that the mounting
holes align. See Figure 2, Detail B.
Figure 2
3(5., #,(3 3(: .(059: 3(5.,
6- ",*,7:(*3, 99,4)3>
#/6=5 59:(33,+ -68 865: !(5,3 6;5:
"
5 05, 6;73,8 #,(:,+ 05
",*,7:(*3, 99,4)3>
3. Cut the panel using the dimensions provided in
Figure 3.
Figure 3
1$'.' ( & #$ %( ,,
'' $(
44
&
05'
!3(*,9
44
&
05'
44
&
05'
,0% 6: :6 #*(3,
44
&
05'
#+&#, (,%&#'"#" ,, %+).$% #!#*- !'# &-
"
4. Insert the receptacle assembly into the panel
until the flange seal is flat against the panel. See
Figure 4.
5. Thread four No. 4 screws into the mounting
holes, and tighten until secure.
Figure 4
!
)-#
!
Components of the receptacle kit are not repairable.
DO NOT use defective or damaged components.
Revisions to this instruction sheet include:
Updated document to corporate requirements
