Travor Speedlite User Instructions

The TRAVOR Speedlite is an EOS-dedicated, high-output flash unit automatically It can serve as an on-camera flash as well as a master unit or a slave unit in a wireless, multiple-Speedlite system. EN Before using the speedlite,read this instruction manual and your camera’s instruction manual to familiarize yourself with the speedlite operations.

2.To avoid possible safety accident, do not use the flash light on the people who need a high degree of attention. 3.To avoid fire or electrical shock, do not expose this product to rain or moisture. 4.To avoid short circuit, be sure the batteries contacts are securely packed and in accordance with local provision when handling the batteries. 5.Please place the batteries and the parts which can be allowed mistakenly away from children. 6.Do not disassemble or maintain this product .Touching the internal high voltage circuit will cause electric shock. 7.Remove batteries during long periods of non-use . 8. Please take out the batteries and stop using immediately in case of below: 1. This product is dropped or shocked seriously and the inner part of the product is bared. 2. If the battery leaks corrosive liquids, please take out the battery with gloves. 3. The product gives off strange smell, smokes or heats. 4. When the product is full charged (the charge lamp bright), press < >, flash will not firing Ⅱ.Warning -2- -3- EN EN 1、To avoid overheating and degrading the flash head, do not fire more than 20 continuous flashes. After 20 continuous flashes, allow a rest time of at least 10 min. If you fire more than 20 continuous flashes and then fire more flashes in short intervals, the inner overheating prevention function may be activated to make the recycling time about 8 to20 sec. If this occurs, allow a rest time of about15 min. and the flash will then return to normal. 2、Using size-AA batteries other than the alkaline type may cause improper battery contact due to the irregular shape of the battery contacts 3、Change the batteries should be aware below: 3.1、If you change the batteries after firing many flashes continuously, 3.2、Use a new set of four batteries of the same brand. When replacing the batteries, replace all four at one time 3.3、Size-AA Ni-MH or lithium batteries can also be used. 4、If you set the flash coverage manually, make sure it covers the lens focal length so that the picture will not have a dark periphery.If you use a commercially-available sync cord to connect the camera to the Speedlite's PC terminal, set the flash zoom manually. 5、During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera. After exceeding the number of flashes，multi flash immediately . be care that battery may become warm or hot. . Ⅲ. Caution: Number of flashes ÷ Firing frequency = Shutter speed For example, if the number of flashes is 10 and the firing frequency is5 Hz, the shutter speed should be at least 2 sec.

Large and high clear LCD Panel, it is very convenient for you to look into and set the functions on the LCD panel clearly and directly. Master & Slave Modes Providing master function, could control C flash firing and accept C master signal under slave mode. A variety of trigger synchronization A variety of trigger synchronization The product could be Triggered by camera-top ,C master flash ,PC ,S1&S2 modes ( S1 is flash start , S2 is avoiding relight) Large guide number 60@ISO100 flash light New large guide number manual speedlite, supporting M/Multi modes. Ⅳ. Features -4- -5- EN EN Aperture imaging flash preview Aperture preview button on operation ,flash will send out one second continue flash, Radiography for shooting objects. Supper speed of charge recycle system It only takes 1~5 seconds in charging after full power output ,you can use the external power pack to accelerate the charging speed once more . Providing charging socket for external power pack The products provide charging socket for external power pack ,to meet your higher demand for charging cycle and will not miss wonderful moments any more . Providing PC port The product provides PC port; you could make the flash synchronously by connecting to the PC port Sound prompt system Turn on the sound prompt function, different sounds indicate working situation help you focus on shooting, which will make you into taking photos. Power saving mode In the power saving mode, the speedlite will get automatic shutdown sooner; in the non-saving mode, it will take a longer time before automatic shutdown . Advanced options setting The product provides advanced options setting function ,you could custom flash function according to your own need . ZOOM covers around Supporting the flash auto and manual zoom .It can make the flash cover focal length range from 20mm to 200mm cyclic variation, supporting full-size ,middle-size cameras. Fully support ETTL function Exposure Compensation, Exposure Bracketing, Rear-curtain Sync, Exposure Lock, Aperture imaging flash preview, Access to Canon menu.

Wireless sensor AF assist lamp Mounting foot Locking Pin Catchlight Panel(Retracted) Built-in wide panel(Retracted) Contact cover Contacts External power source socket PC Terminal Bracket mounting hole Mini stand pocket Mini stand Shoe ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ 12 11 13 14 -6- -7- EN EN Ⅴ.Part Names ⑤ ⑥ ⑨ ① ② ③ ④ ⑧ ⑩ ⑦ 11 13 14 15 12 15 LCD Panel Volume adjustment custom function setting button Wireless /Linked shooting button Flash mode Pilot lamp/Test firing/wireless slave power on button Mounting foot's lock lever Lock-release button Dust-and water-resistant adapter Bounce angle Bounce lock release button Rear-curtain sync/HSS shortcuts Battery compartment cover Battery compartment lock lever Zoom /Wireless setting button Power switch (OFF: power off, Lock button/Dial lock ON: power on) Flash exposure confirmation light Select Dial Select/set button 17 18 19 20 21 22 23 32 31 30 29 28 27 26 25 24 33 34 35 16 18 27 Fn ZOOM MODE 17 19 20 21 22 23 24 25 26 28 29 30 31 32 33 34 35 16 Synchronization terminal

cover and slide it as shown by the arrow.When the cover clicks in place,it will be locked. Use your thumb to press the battery compartment lock lever,then slide it to as shown by the arrow ① to open the cover. Install the batteries :Make sure the +and -battery contacts are properly oriented as shown in the compartment . -9- Flash ratio [ ] FEB Manual flash/Multi (Stroboscopic)flash [ ]Advanced setting [ ]FEC Rear-curtain sync [ ] [ ] Auto zoom forimage size Slave ID Slave group Flash ratio Flash range scale Indicator(meters) Indicator(feet) [ ] [ ] [ ] [ ] Master ETTL autoflash Channel Slave Manual Aperture FEB status Stroboscopic flash count Stroboscopic flash frequency Manual flash 1/3-stop increment indicator Advanced setting Zoom focal length Advanced option NO. Manual flash output level flash exposure compensation amount FEB compensation amount Flash mode Master flash on: Master flash off: Slave flash: HSS [ ]

-10- -11- Attach the speedlite Slip the speedlite’s mounting foot into the camera’s hot shoe all the way. Secure the speedlite On the mounting foot,slide the lock lever to the right,When the lock lever clicks in place,it will be locked. Detach the speedlite While pressing the lock-release button,slide the lock lever to the left and detach the speedlite. EN EN Ⅶ.Basic functions 1.Power-on and Power-off Power-on and Power-off: the power of the speedlite can be turned on by press to ON ,and turned off by pressing to OFF. Turn on the power of the speedlite, when (PILOT) turns red that the speedlite can flash. If the charging is less, the flash will automatically shutdown, then you need to replace with new batteries. You can press the testing button (PILOT) to test whether the speedlite works normally, after use, hold the power to OFF to power off. 2. Button/Dial Lock By setting the power switch to (LOCK),you can turn off flash's button and dial operations. Use this to against the flash function settings from being accidentally changed after you set them. 3.M You can set the flash output from 1/128 power to 1/1 full power in 1/3- stop increments. Use a hand-held flash meter to determine the required flash output to obtain a correct flash exposure Press the (MODE) button so that (M) displayed. By choose setting and dial button to adjust flash luminance in 0.3EV increments. Adjust the camera and press the shutter, the speedlite will flash with the synchronic signal of the camera. mode

of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output. Press the (MODE) button so that (Multi) displayed. Press the select button and select dial to adjust flash output, the number of flashes and firing frequency. The adjustment scope of output level is 1/128-1/64-1/32-1/16-1/8-1/4,the scope of flash frequency is from 1~100.Adjustment method :please press select setting button to select setting items (firing),and use the select dial to adjust the parameters. After the setting is completed, press select setting button to confirm the setting. Multi mode The charging speed of speedlite is slow under the situation that the electricity quantity of the battery is insufficient ,which may cause the occurrence of the high-frequency flash, please reduce the flash frequency or change new battery under this situation .Notice: the shutter should keep open until the flash stopped under the Multi mode . 5. ETTL mode Set cameras' shooting mode to (AV) ,Aperture prior to auto exposure ,(TV) ,shutter prior to auto exposure or (M),then you could use ETTL to auto flash .Under the mode of ETTL , Exposure Compensation, Exposure Bracketing, Rear-curtain Sync, Exposure Lock, Aperture imaging flash preview, Access to Canon menu . 6．Test flash whether in any mode ,you can press（PILOT）button to test if the speedlite flashes normally .When testing the speedlite, the speedlite will give flash at relevant output level in accordance with the chosen output power setting. 3.M You can set the flash output from 1/128 power to 1/1 full power in 1/3- stop increments. Use a hand-held flash meter to determine the required flash output to obtain a correct flash exposure Press the (MODE) button so that (M) displayed. By choose setting and dial button to adjust flash luminance in 0.3EV increments. Adjust the camera and press the shutter, the speedlite will flash with the synchronic signal of the camera. mode

． You can customize Speedlite features to suit your shooting preferences. You do this with Custom Functions. -14- -15- EN EN Setting No. Settings & Description Function Custom Function No. Distance indicator display Auto power off Modeling flash FEB auto cancel FEB sequence Flash metering mode Quickflash with continuous shot Test firing with autoflash Meters(m) Feet(ft) Enabled Disabled Enabled(Depth-of-field preview button) Enabled(Test firing button) Enabled(with both buttons) Disabled Enabled Disabled 0→-→+ -→0→+ E-TTL Ⅱ/E-TTL TTL External metering: Auto External metering:Manual Disabled Enabled 1/32 Full output 7．Setting the ZOOM coverage Flash automatically zoom :press ZOOM button to adjust covered coverage ,when (M) don not display ,set flash to the camera that supporting ETTL system ,flash led will move back and forth along with the change of focal length to accommodate different covered coverage . The speedlite manual ZOOM: press ZOOM button to adjust the coverage, default in 24mm.Manually set the zooming position: press ZOOM button to adjust the coverage ,when (M) displayed , you can manually adjust the coverage (20,24,28,35,50,70,80, 105,135,200mm) setting method :press ZOOM button ,the ZOOM icon firing ,you can adjust the flash coverage by selecting dial . Notice: used in wide-angle diffusion board ,flash coverage will range to 14mm. C.Fn-00 C.Fn-01 C.Fn-02 C.Fn-03 C.Fn-04 C.Fn-05 C.Fn-06 C.Fn-07

indicate its working situation. Sound fuction is default to off condition,The meanings of the sounds can be found in the table below: The sound form Meaning Operation Tick twice The speedlite is started/Sound prompt is enabled/A standard flash is obtained. The flash is in the charging state Normal Waiting for the completion of charging Three ticks,two times The exposure may be over Tick tick tick The power is not enough The speedlite is fully charged, and can be used. Please replace the batteries. Normal Asjusting exposure compensation or changing shooting condition Adjusting exposure setting or shooting condition The exposure may be excessive AF-assist beam firing Auto zoom for sensor size Slave auto power off timer Slave auto power off canel Flash recycle with external power source Flash exposure metering setting Enabled Disabled Enabled Disabled 60 minutes 10 minutes Within 8 hours Within 1 hour Flash and external power External power source Speedlite button and dial Speedlite dial only Auto zoom light &Pilot Pilot -16- EN EN C.Fn-08 C.Fn-09 C.Fn-10 C.Fn-11 C.Fn-12 C.Fn-13 C.Fn-20 OFF C.Fn-21 Flash light range C.Fn-22 LCD Display Universal Prior to flash GN coverage range Lighting for 12s OFF Continue ON C.Fn-23 Battery check on slave flash 2 hours 3 hours 4 hours 5 hours Auto power off (Sleep mode) Clearly defined function setting C.Fn-25 NO Customize the default recovery setting C.Fn-24 Tick three times Auto power off(Sleep mode) C.Fn-24 2 minutes(DEFAULT) 5 minutes 10 minutes 30 minutes -17- Sound control settings

Slave unit setting, can accept C and travor signal. -18- -19- EN EN 10. Access to Canon camera menu.(Only Latest Canon camera). We could operate the flash via newest Canon camera's menu that has ETTL function. Flash's related parameter could be set by “External flash function setting”and “External flash C.Fn setting” on flash control menu: switch ETTL mode/manual flash mode and Multi flash, wireless flash setting , Rear-curtain Sync, Exposure Bracketing ,Exposure Compensation, focal length and advanced option function etc. 12. Modeling light function Press down the camera's aperture preview button ,flash will send out continuous flash lasting one second. Note: please control the flash fired less than 10 times, should let flash have a rest about 10~15 minutes to avoid heat or damage. 13. PC synchronous port (for input) By connecting to the PC synchronous port, you can make the flash synchronously. 14. Power saving mode Please press C,Fn-24 custom function setting. 1. Set the master unit Set the speedlite wireless select to master.Setting method: press the < >button by select dial to master, then press the select setting button to confirm. Press the ZOOM button , (CH), master flash icon or（R AT I O）will firingto the communication channel or slave setting ,at this time ,you can set slave unit communication channel number(1,2,3,4)or slave unit group (A,B,C) via select dial, then press select setting button to confirm setting . 11.Volume adjustment By pressing < >button for three levels to adjust the volume ,could be setted from C.Fn"Custom function setting”and ON or OFF for the voice from C.Fn-20.

If set the flash with three group to (A), they will be controlled as one flash of slave group by master unit. Multi-speedlite, wireless lighting configurations master unit.Press the testing flash button of master unit to test whether the flash is normal; if slave unit do not flash, please inspect the angle and distance between and master unit. SLAVE MASTER Outdoors Indoors 15m(49.2Ft) 10m(32.8Ft) 8m(26.2Ft) 12m(39.4Ft) EN EN 3. Multi-Speedlite, Wireless Lighting Configurations You can create two or three slave unit group to meet multi-directional shooting, the manual flash output and stroboscopic is set by master speedlite. ⑴. Wireless flash with two slave group Set communication channel: 1,2,3,4 Set groups: Set two flashes to A, B Set master unit: set communication channel, set the controlled group A: B of master unit, or set the flash output of each group, then you can flash shooting. ⑵.Wireless flash with three slave group Set communication channel: 1,2,3,4 Set groups: Set two flashes to A, B, C Set master unit and shooting: set communication channel, set the controlled group A: B: C of 2. Set the slave unit Set the speedlite wireless select to SLAVE. Setting method :press the < >button by select dial to slave, then press the select setting button to confirm. Press the ZOOM button ,(CH)or (A) will firing to the communication channel or slave setting ,at this time ,you can set slave unit communication channel number(1,2,3,4)or slave unit group(A,B,C) via select dial, then press select setting button to confirm setting .When there has other photographers use the wireless control and you do not want to be disturber by them, please change the channel no. to avoid different signal.

You can buy external charging boxes and connect it to the charging port of Speedlite, after flash, the charging box will charge the speedlite.You can set C.Fn-00 to meet you higher need . High-speed continuous shooting The Speedlite can realize the high-speed continuous shooting function, please set the in the continuous shooting form and then shoot. Please: The number of the photos that can be continuous shot is releated with the output level .Please use the fully charged battery. Ⅸ.The advanced application Reflection flash Bounce flash means to take photos by making flash light head aimed at wall or ceiling and using the light reflected back from the ceiling or wall to light the desired object,so that the shade behind the object can be decreased to get more natural shooting effect .If the wall or ceiling is too far , the bounce flash may be too weak to get enough exposure . The wall or ceiling should be even and white in order to get efficient reflection ;if the reflection surface is not white , color cast may appear in photo. -22- -23- EN EN Set S1/S2 mode S1 Mode: When the flash is in S1 mode, it will work with the first work of the master flash synchronously, with the result consistent with the use of radio slave, To use this mode correctly, the master flash should be set at manual flash and TTL flash system with preflightfunction and the red-reduction function with multiple flashes should not be used . S2 Mode: It is also called“pre-flash cancel mode”. This mode is similar with S1mode,but it can neglect the pre-flash given by TTL flash .Therefore ,it can support the main flash working in TTL mode. In particular, if S1 mode cannot flash correctly and synchronically with your internal flash, you can try to use S2 mode.The following situation shall be avoided when the S1 and S2 modes are used: the red eye reduction function of the main light is used;the order mode(Nikon) or wireless mode(Canon) of the master is used ;the ST-E2 is used as the flash controller. By pressing the < >button to chose S1 or S2 ,that is S1 or S2 mode. These twomodes are suitable to be used as off-camera auxiliary light, so as to create a variety of lighting effects. They are suitable for manual flash environment and TTL flash environment respectively .Under these two modes, the way to adjust the output level is like that in M mode.

You can use the exposure compensation function of the camera to compensate flash output so as to make shooting effect better meet your requirements .You can also make compensation of flash brightness with the (LEFT)(RIGHT) button within the range of +-6ev ,,with the precision of 1/3ev. Every press the button,the compensation setting will be displayed on LCD panel . Rear curtain Sync You can use slow-speed shutter to produce trailing smear for the object and the flash light will flash at the moment when the shutter is going to be shut, which means the rear-curtain sync function . (For the rear curtain sync setting ,refer to your camera manual for setting).You can turn on or turn off the rear curtain sync by pressing the rear curtain sync hotkey on panel of flash. Note :when flash is used as slave unit ,the rear curtain sync function can not be set on the speedlite. Exposure Bracketing FEB The FEB function is set on the camera or speedlite.For the specific setting method ,refer to your camera instructions .After the FEB is set ,after 3 photos are taken ,exposure compensation will be made automatically in the sequence of ,for example ,“normal-under-over”.This function helps you improve the success rate of photo taking . The setting method on the flash :press the (UP)(DOWN) button to adjust the exposure bracketing amount . Note :For FEB,set the camera's drive mode to single shooting.Be sure the flash is ready before shooting. Creating a Catchlight With the catchlight panel, you can create a catchlight in the subject's eyes to add life to the facial expression. Wide-angle diffusion board Pull out the wide-angle diffusion board, push back the reflection board and arrange them as per the figure ,the flash scopes will extent and the flash effect will be softer and more natural. Pull out the wide-angle diffusion board Push back the wide-angle diffusion board FEL Lock(Canon ) To use this function, cover the subject, for which flash exposure will be locked at the center of the viewfinder of camera, press the button (*)of the flash exposure lock, and the flash light will pre-flash and the camera will calculate the appropriate flash output data .Now you have some time for decomposition ,after which ,you can take photo.(The function can be used only when it is supported by your camera. For the setting method ,refer to your camera instructions.) -24- -25- EN EN

convenient when you want to use aperture priority for fill-flash portraits. if you set a shutter speed that is the same or slower than the camera＇smaximun flash sync speed, will not be displayed in the viewfinder. With high-speed sync,the faster the shutter speed,the effective flashrange will become. Check the LCD panel for the effective flash range. To return to normal flash,press the < >button again. The< > icon will disappear. Stroboscopic flash cannot be set. < > Auto Zoom for Image Size EOS DIGITAL cameras have one of three image sizes.The lens＇effective focal length will differ depending on the camera＇s image size, the speedlite automatically recognizes the EOS DIGITAL camera＇s image size and automatically sets the flash coverage for lens focal lengths from 24mm to 105mm. When the Speedlite is attached to a compatible camera,< >will appear on the Speedite＇s LCD panel. Select Press the< >button so that < >is displayed In the viewfinder,check that the< > icon is displayed < > -26- -27- EN EN

1 - 199 Hz 1-100 Specification Ⅹ. Type Type on-camera speedlite Flash coverage 20 - 200mm (14mm with wide panel) Auto zoom (automatically set flash covered coverage of proper focal length and image size) · Manual zoom · Swinging/tilting flash head (bounce flash) Exposure Control Exposure control system ETTL,Manual flash,frequency flash Manual, FEB: ±6 stops in 1/3-stop increments (Manual and FEB can be combined) Multi flash Flash Recycling (with size-AA alkaline batteries) Flash exposure compensation Recycling time Flash-ready indicator Normal flash: Approx. 0.1 - 5 sec. / Red pilot lamp lights Quick flash: Approx. 0.1 - 2.5 sec. / Green pilot lamp lights Wireless Flash Transmission method Optical pulse Flash NO. -28- -29- EN EN Channel Wireless options OFF, Master, and Slave Controllable slave groups 3 (A, B, and C) Power Source Power Source Battery life (Approx. flash count) Weight 406 g Power off after certain period of idle operation 100 - 700 flashes (with size-AA alkaline batteries) Four size-AA alkaline batteries and lithium batteries also usable Power saving Dimensions 215 x 79 x 63 mm Flash exposure lock use (FEL) button or (*)button Rear-curtain Sync Provided Lamp light High Speed Sync Provided（Mode list） Flash exposure confirmation

EN EN The Speedlite does not fire. 1. The batteries are installed in the wrong orientation. Install the batteries in the correct orientation. 2. The Speedlite's internal batteries are exhausted: If the flash recycling time takes 30 sec. or longer, replace the batteries. Install the Speedlite's internal batteries even when you use an external power source. 3. The Speedlite is not attached securely to the camera. Attach the Speedlite's mounting foot securely to the camera. 4. The electrical contacts of the Speedlite and camera are dirty. Clean the contacts The slave unit does not fire. 1. The slave's wireless mode is not set to . Set it to . 2. The slave unit(s) is not positioned properly. Place the slave unit within the master unit's transmission range. Point the slave unit(s)'s sensor toward the master unit. The power turns off by itself. Auto power off took effect:Press the shutter button halfway or press the test firing button XI. Possible problems during use and solutions 1/128 1.3/4.3 2.5/8.2 2.7/8.9 3.2/10.5 3.7/12.1 4.4/14.4 4.7/15.4 5.1/16.7 2.3/17.5 5.2/1 7 5.3/1 7. 4 Flash output Flash coverage (mm) 1/1 1/2. 1/4 1/2. 1/16 1/32 1/64 15/49.2 28/91.9 30/98.4 36/118.1 42/137.8 50/164 53/173.9 58/190.3 10.6/34.8 19.8/65 21.2/69.6 25.5/83.7 29.7/97.4 35.4/116.1 37.5/123 41/134.5 7.5/24.6 14/45.9 15/49.2 18/59.1 21/68.9 25/82 26.5/86.9 29/95.1 5.3/17.4 9.9/32.5 10.6/34.8 12.7/41.7 14.8/48.6 17.7/58.1 18.7/61.4 20.5/67.3 3.8/12.5 7/23 7.5/24.6 9/29.5 10.5/34.4 12.5/41 13.3/43.6 14.5/47.6 2.7/8.9 4.9/16.1 5.3/17.4 6.4/21 7.4/24.3 8.8/28.9 9.4/30.8 10.3/33.8 1.9/6.2 3.5/11.5 3.8/12.5 4.5/14.8 5.3/17.4 6.3/20.7 6.6/21.7 7.3/24 14 24 28 35 50 70 80 105 20 26/85.3 18.4/60.4 13/42.7 9.2/30.2 6.5/21.3 4.6/15.1 3.3/10.8 135 200 59/193.6 41.7/136.8 29.5/96.8 20.9/68.6 14.8/48.6 10.4/34.1 7.4/23.3 60/196.9 42.4/139.1 30/98.4 21.2/69.6 15/49.2 10.6/34.8 7.5/24.6

1.The wide panel has been pulled out for bounce flash, Retract the wide panel. The periphery or bottom of the picture looks dark. 1. When you set the flash coverage manually, the setting was a higher number than the lens focal length, resulting in a dark periphery.Set the flash coverage that is a lower number than the lens focal length or set it to auto zoom. 2. If only the bottom of the picture looks dark, you were too close to the subject. If the subject is closer than 2 m/6.6 ft, tilt the flash head downward by 7° (bounce flash). The flash exposure is underexposed or overexposed. 1. There was a highly reflective object (glass window, etc.) in the picture. Use FE lock. 2. The subject looks very dark or very bright. Set flash exposure compensation. For a dark subject, set a decreased flash exposure. And for a bright subject, set an increased flash exposure. -32- EN The latest version of this manual can be obtained from http://www.travor.cn. The functionality of this manual is obtained in accordance with the test conditions of company. Without notice if the design and specifications are changed.

旅行家闪光灯是专用的高能闪光灯，可以作为机载闪光灯、无线多灯闪光系统的主控 单元或从属单元。 一、感谢您购买旅行家产品。 1、请不要近距离对人体的眼睛使用闪光灯闪光，否则有可能对人体视网膜造成伤害。 2、请不要对需要高度注意力的人使用闪光灯闪光，否则有可能引发安全事故。 3、请勿让本产品淋雨或受潮，以免发生火灾或触电。 4、处理电池时，请将电池的触点包裹好以避免短路，并请遵守好当地有关处理电池 的规定。 5、请将电池或容易误吞的东西远离儿童存放，如果误吞了物体，请立即与医生联系。 6、请勿自行拆卸或维修本产品，如果接触本产品内部的高压电路，可能会触电。 7、长期不使用本产品时，请取出所有电池。 8、如发现以下情况，请立即取出电池并停止使用： 8.1、本产品跌落或受到强烈冲击，使产品的内部裸露; 8.2、电池内部腐蚀性液体泄漏，此时应带手套取出电池; 8.3、产品发出奇怪的气味，发热或冒烟; 8.4、当本产品充电充满时（充电指示灯亮）,按下< >按钮，闪光灯不闪光。 二、警告： -1- -2- 中文 中文 使用闪光灯之前，请阅读此使用说明书和相机手册以熟悉闪光灯的操作。

1、为防止闪光灯灯 过热并损坏，请勿进行20次的连续闪光或10次的频闪闪光。连续闪 光后，要让闪光灯至少冷却15分钟。如果您在闪光次数超过后马上进行多次闪光，内 部的防过热功能可能会被激活，使充电时间变成8至20秒左右。如果发生这种现象，请 让闪光灯冷却约15分钟，闪光灯便会恢复正常。 2、因为电池触点的外形不规则，使用碱性电池以外的AA型电池可能会导致电池接触不良。 3、更换电池时需注意以下情况： 3.1、如果在连续闪光多次后更换电池，小心电池可能会发热或烫手。 3.2、请使用4节相同品牌的新电池。更换电池时,请同时更换4节。 3.3、您也可以使用AA型镍氢(Ni-MH)或锂电池。 4、为确保其覆盖镜头焦距，需手动设置闪光覆盖范围，这样照片就不会出现阴影边缘。 如果使用市售的同步电缆连接相机和闪光灯的PC端子，需手动设定闪光覆盖范围。 5、在频闪模式，到闪光停止为止快门应保持开启状态。使用下面的公式计算快门速度， 然后用相机进行设置。 头 三、注意事项： 四、产品特点 -3- -4- 闪光次数/闪光频率=快门速度 例如:如果闪光次数是10，闪光频率是5HZ,快门速度则至少2秒。 中文 中文 中文 大尺寸，高清LCD液晶显示 本产品配备大尺寸，高清LCD液晶显示，使用便捷，便于您清晰、直观的查看或者设置闪 光灯各项功能。 主控和从控模式（Master和Slave） 有主控功能，可控制C家闪光灯闪光，在从控模式下能接受C家主控指令信号。 多种触发同步方式 本产品可通过相机机顶触发、佳能主控闪光灯指令触发、PC同步触发、S1和S2模式（S1 为闪光立即触发、S2为避预闪触发）。 国产大指数GN60@ISO100闪光灯 新一代高指数手动闪光灯，支持ETTL、M、Multi模式。 ZOOM覆盖范围广泛 支持灯头自动及手动变焦，可以使灯头覆盖距在auto、20~200mm之间变动；可支持全幅、 中幅相机。

⑤ ⑥ ⑨ ① ② ③ ④ ⑧ ⑩ ⑦ 11 13 14 15 12 16 全面支持ETTL功能 曝光补偿、闪光包围 、后帘同步、曝光锁定、光圈预览造型闪光、佳能相机菜单访问。 光圈预览造型闪光 操作机上的光圈预览按钮，闪光灯将会发出1秒钟的持续闪光，为拍摄对象造型。 极速回电系统 全光输出回电时间仅需1-5秒，您可以使用外置充电盒对回电时间再次加速。 配备外置电源插座 本产品配备了外置电源插座，满足更高的回电需求，再也不会错过精彩瞬间。 配备PC同步端子 本产品配备了PC同步端子，使您更便于PC同步线，让您的闪光灯同步触发。 声音提示系统 开启声音提示功能，闪光灯发出的声音提示其工作状态，让您更好的投入拍摄创作过程。 节电模式 在节电模式下，闪光灯会进行休眠及更快的自动关机；在非节电模式下则不休眠，不自动 关机。 高级选项设置 本产品具备高级选项设置功能，您可以根据自己的需求自定义闪光灯的功能。 曝光 五、部件说明 ① 闪光灯头/无线传输器 ② 无线传感器 ③ ④固定座 锁定销 ⑤ 眼神光板(收回状态) ⑥ 内置广角散光板(收回状态) ⑦ 接口盖 ⑧ 电子触点 ⑨ 外置电源插座 ⑩ 端子 PC 支架安装孔 微型基座袋 微型基座 热靴插座 辅助对焦灯 12 13 14 11 -5- -6- 中文 中文 15 16 同步端子

手动闪光输出级别 闪光曝光补偿量 闪光包围曝光补偿量 [ ]闪光包围曝光 手动闪光/ 多次(频闪)闪光 [ ]自定义功能 [ ]闪光曝光补偿 后帘同步 闪光模式 闪光开启: 闪光关闭: [ ]手动变焦 光圈 闪光包围曝光状态 频闪闪光次数 频闪闪光频率 手动闪光1/3档增量指示 自定义功能编号 自定义功能设置 变焦焦距 [ ]适合图像尺寸 自动变焦 从属账号 从属账号下划线 闪光光比 闪光范围标尺/ 闪光光比标尺 距离单位指示（米） 距离单位指示（英尺) [ ]闪光光比 [ ]从属 [ ]频道 [ ]主控 音量调节 自定义功能设置按钮 无线按钮/联动拍摄按钮 闪光灯模式 指示灯/测试闪光/无线从属单元电源开启按钮 固定座锁定杆 锁定释放按钮 防尘适配器 垂直旋转角度 垂直旋转锁定释放按钮 后帘同步/高速同步快捷键 电池仓盖 电池仓锁定杆 变焦按钮/无线设置按钮 电源开关 (OFF电源关闭；LOCK按钮/ 拨盘锁<电源开启>;ON电源开启） 闪光曝光确认指示灯 选择拨盘 选择设置按钮 液晶显示屏 27 26 25 24 23 19 21 22 17 18 20 31 30 29 28 35 -7- -8- 中文 中文 ETTL闪光 高速同步 33 34 18 27 Fn ZOOM MODE 17 19 20 21 22 23 24 25 26 28 29 30 31 32 33 34 35 [ ] 32

六、产品安装说明 1．闪光灯打开与关闭 闪光灯电源的打开与关闭：将电源开关拔到ON打开电源，将电源开关拔到OFF关闭 电源。开启闪光灯电源后，当< >亮红灯时，表示可以进行闪光。 电池电量不足时，闪光灯将自动关机，需更换新电池。 您可以通过按< >按钮来测试闪光灯是否正常，使用完毕后，将电源开关拔到 OFF即可关闭电源。 七、基本功能应用 -9- -10- 安装闪光灯:滑动闪光灯固定座使其完全插入相机的热靴插座。 拧紧闪光灯: 的位置，闪光灯将被锁定。 将固定座上的锁定杆滑动到右侧。在锁定杆发出咔嚓声 取下闪光灯: 光灯。 在按锁定释放按钮期间，将锁定杆滑动到左侧并取下闪 打开电池仓盖：用您拇指按电池仓锁定杆，然后按照箭头所示方 向①滑动电池仓锁定杆将电池仓盖打开。 安装电池：按电池仓中的指示确保电池的正负触点朝向正确。 关上电池舱盖：按箭头所示方向滑动电池仓盖将其关闭在电池仓 盖发出咔嚓声的位置，电池将被锁定。 1.安装电池 2.将闪光灯安装到相机上 中文 中文 3．M模式：您可以在1/128功率至1/1全功率间以1/3档为增量设置闪光输出功率。 为获得正确的闪光曝光，请使用手持的闪光测光表确定所需的闪光输出功率。 按下按钮液晶屏上显示M模式。 通过选择设置按钮和选择拔盘以0.3EV作为调节增量调节闪光亮度，调整相机后按下 快门，闪光灯会在相机同步信号下进行闪光。 2. 按钮/拨盘锁定 通过将电源开关设为.可以关闭闪光灯的按钮和拨盘操作，使用此功能以防止 设定闪光灯功能设置意外的将其改变。

5. ETTL模式 将相机的拍摄模式设置为[AV](光圈优先自动曝光)﹑[TV](快门优先自动曝光)或[M](手 动),您就可以使用ETTL进行自动闪光.在ETTL模式下，支持曝光补偿、闪光包围曝光、 后帘同步、曝光锁定、光圈预览造型闪光、佳能相机菜单访问。 6．测试闪光灯：无论在哪种模式下，您都可以通过< >按钮来测试闪光灯是否闪 光正常。测试闪光灯时，闪光灯会根据所选择的输出功率等级发出相应亮度的变化。 7．ZOOM覆盖范围设置 灯头自动变焦：按下< >按钮调节覆盖范围,当不显示(M) 时,将闪光灯安装在支持ETTL系统的相机上，闪光灯管将 会随着镜头焦距变化而前后移动，以适应不同的闪光覆 盖范围。 手动设置灯头的变焦位置：按下按钮调节覆盖 范围，当同时显示（M）时，您可以手动调整闪光覆盖 范围（20，24,28,35，50，70，80，105，135，200mm） 设置方法：按下ZOOM按钮，变焦焦距图标闪烁，此时再 选择拔盘可以调节闪光覆盖范围。 注意：使用广角扩散板，闪光覆盖范围将扩展至14mm。 4．Multi模式：使用频闪闪光，可以发出一系列快速的闪光。它可以在一张照片上拍摄移 动物体的多个图像。您可以设置闪光频率、闪光次数和闪光输出功率。按下按 钮至液晶屏上显示Multi模式。 通过选择设置按钮和选择拔盘来调整输出功率，闪光次数及闪光频率输出功率的调 整范围是1/128-1/64-1/32-1/16-1/8-1/4;闪光次数范围为1~100。 调节方法：请按下选择设置按钮选择设置项目（闪烁），通过选择拔盘即可调节其 参数，设置完成后，再按下选择设置按钮以确定设置。 -11- -12- 中文 中文 电池电量不足的情况下，闪光灯充电速度较慢，可能会引起高频率闪光出现漏闪，在这 种情况下，请降低闪光频率或更换新电池。注意：在频闪闪光的过程中，直至闪光灯停 止为止，快门应保持开启状态。

8．C.Fn自定义功能设置 您可以按照自己的拍摄喜好自定义闪光灯的功能。使用自定义能来完成设置： -13- 中文 中文 0→- + → - 0 + →→ C.Fn-09 C.Fn-08 C.Fn-11 C.Fn-10 C.Fn-13 C.Fn-12 C.Fn-01 C.Fn-00 C.Fn-03 C.Fn-02 C.Fn-05 C.Fn-04 C.Fn-06 C.Fn-07 关 C.Fn-20 声音控制设置 开 C.Fn-21 C.Fn-23 光线分布 标准 闪光指数优先 均匀覆盖 C.Fn-22 液晶显示照明 照明12秒 关闭显示屏照明 持续照明 自动对焦辅助光和 指示灯 指示灯 从属闪光灯电池检查 -14- 自动 C.Fn-24

12．造型闪光 操作相机或闪光灯上的光圈预览按钮,闪光灯将会进行1秒钟的连续闪光, 即造影闪光. 注意:请尽量将连续造型闪光次数控制在10次以下;连续进行造型闪光操 作后,需让闪光灯闲置10至15分钟,以免闪光灯头过热或损坏. 13．PC同步接口（输入） 通过连接PC同步口，可以使闪光灯同步闪光。 14．节电模式 可以按“C.Fn自定义功能设置”表格的“C.Fn-24”进行调节。 15．相机菜单访问(仅佳能较新机型) 在支持ETTL的佳能较新型相机上可通过相机菜单访问来操作闪光灯。在闪 光灯控制菜单中的“外接闪光灯功能设置”及“外接闪光灯的自定义功能 设置”可以设置闪光灯相关参数；如切换ETTL模式/手动闪光模式及几次闪 光模式（MULTI)、无线闪光设置、后帘同步、闪光包围曝光、曝光补偿、 焦距及高级选项功能等。 滴滴滴 滴滴滴 曝光可能过度 调节曝光设置或拍摄条件 滴 滴 滴 曝光可能不足 调节曝光设置或拍摄条件 电量不足,闪光灯将自 动关机 闪光灯充电完成,可以 进行闪光 连续快速响 嘀---长响 请更换电池 正常 -15- -16- 中文 中文 11.音量调节 通过按< >按钮分大中小三个等级进行音量大小调节,可在C.Fn“自定义功能设置” 表格的“C.Fn-20”打开和关闭声音。 C.Fn-24 恢复默认设置 暂无 C.Fn-25 清除自定义功能设置 自动 正常 滴滴滴3声

八、无线闪光 1、主控单元设置 将闪光灯的无线选项设置为MASTER。设置方法：按 >按钮，选择MASTER，此时按选 择设置按钮确认。再按按钮，,主控闪光符号或(RATIO)会闪烁，表示进入 通信频道或从属单元组设置状态，此时通过选择拔盘即可设置单独从属单元通信频道数 （1,2,3,4）或从属单元分组（A,B,C），再按选择设置按钮以确认设置。 < 2、从属单元设置 将闪光灯的无线选项设置为SLAVE。设置方法：按 >按钮，选择SLAVE。再按 按钮，< >或< >会闪烁，表示进入通信频道或从属分组设置状态，此时通 过选择拔盘即可设置单独从属单元通信频道数（1,2,3,4）或从属分组（A,B,C）， 再按选择设置按钮以确认设置。当环境中还有其他摄影师使用无线控制而你又不希望 被对方干扰，请更改频道编号可防止信号混淆。 < CH A 3、多台闪光灯，无线闪光配置 您可以创建两个或三个从属单元组以完成多方位的拍摄需求。并由主控闪光灯设置 ETTL 手动闪光输出、频闪等。 （1 本产品组成两个从属单元组的无线闪光 　　 设置通信频道：1,2,3,4 　 设置分组：将两台闪光灯分别设为A、B组。 设置好主控单元：设置通信频道；设置主控单元的受控单元组A:B，或设置各分组的 手动闪光输出，即可进行闪光拍摄。 自动闪光拍摄的闪光光比、 ） 从控单元设置接收C家信号。 主控单元设置，主控闪光时，可自动传输信号给C家闪光灯和本产品 。 （2）本产品组成三个从属单元组的无线闪光 　　 设置通信频道：1,2,3,4 设置分组：将三台闪光灯分别设为A、B、C组。 设置主控单元并拍摄：设置通信频道，设置主控单元的受控单元组A:B:C。 中文 中文 -17- -18-

按下主控单元的测试闪光按钮，测试闪光是否正常；如果从属单元不闪光，请检查本产品 对着主控单元的角度及其到主控单元的距离。 S1/S2模式设置 通过按 >按钮选择 ，即进入S1或S2模式。这两种模式适合作为离机副灯使 用，以创建多种照明效果，它们分别适合于手动闪光环境和TTL闪光环境。在这两种模式 下调整输出亮度与M模式方法一样。 < (S1)或(S2) S1模式：当闪光灯处于S1模式，它会与主闪光灯的第一次闪灯同步触发闪光，效果与使 用无线引闪器一致.要正常使用该模式，您的主闪光灯应设置为手动闪光，不应使用具 有预闪的TTL闪光系统，也不应使用具有多次闪光的红眼减轻功能。 S2模式：又被称为“预闪光取消模式”，该模式与S1模式类似，但它能忽略TTL闪光灯 发出的预闪，因此可以支持工作在(TTL)模式的主闪光灯。特别地，如果S1模式无法与您 的内置闪光灯正确同步闪光，您可以尝试使用S2模式。请注意使用S1 、S2模式时避免以 下情况：主灯使用红眼减轻功能,主灯使用指令（尼康）或无线模式（佳能），使用 ST-E2作为闪光控制器,底座接引闪器。 SLAVE MASTER 多台闪光灯，无线闪光配置 提示：主控单元如果设置了,或禁用C分组闪光，则设置为C分组的从属单元 将不会闪光。 如果将三个本产品闪光灯的分组都设置为，那么它们将被作为从属单元组的一个闪光 灯受主控单元控制。 中文 中文 -19- -20-