Trane IntelliPak RA 20 Installation, Operation And Maintenance Manual

width supply fan 2100 RPM 2000 RPM 1900 RPM 1800 RPM 1300 RPM 1700 RPM 1600 RPM 1500 RPM 1200 RPM 1100 RPM 1400 RPM 950 RPM 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0 2500 5000 7500 10000 12500 15000 17500 20000 22500 25000 27500 Sta!c Pressure, Inches w.c. Airflow, CFM NNoottee:: Maximum airflow (for cULus approval) as follows: 40 ton - 18,000 CFM, 50/55 ton - 24,750 CFM Figure 51. 40, 50 and 55 ton, 24.5 inch - 9 blade - 100% width supply fan 2000 RPM 1900 RPM 1800 RPM 1700 RPM 1600 RPM 1500 ...

This checklist is intended to be a guide for the Trane technician just prior to unit 'startup'. Many of the recommended checks and actions could expose the technician to electrical and mechanical hazards. Refer to the appropriate sections in the this manual for appropriate procedures, component specifications and safety instructions. IIm mppoorrttaanntt:: This checklist is not intended as a substitution for the contractor’s installation instruction. IIm mppoorrttaanntt:: Except where noted, it is implied that the Trane technician is to use this checkl ...

(continued) Object Name(a) Description Object States or values Exhaust Fan Speed Setpoint Active Active setpoint input to relief fan speed control 0 to 100% Exhaust Fan Speed Status Indicates the requested speed to the relief fan, 0% when fan is off. 0 to 100% (a) Reference Integration Guide ACC-SVP02B (or later) Table 38. Exhaust fan speed setpoint summary Exhaust Fan Speed Setpoint Enable Exhaust Fan Speed Setpoint Exhaust fan operation Disable NA Fan under local control Enable 0% Commands the fan off Enable 1% to min speed% Fan o ...

200 250 300 350 400 450 500 90 100 110 120 130 140 150 160 170 180 Suction Pressure, PSIG Discharge Pressure, PSIG 95°F Ambient 85°F Ambient 75°F Ambient 65°F Ambient 105°F Ambient 60T eFlex Variable Speed - circuit 1 only (Use 60T Standard Capacity for circuit 2) NNootteess:: • CChhaarrggiinngg aatt AAHHRRII ffuullll llooaadd ddeessiiggnn ccoonnddiittiioonnss:: Suction pressure = 139 psig; Discharge pressure = 400 psig; Subcooling leaving outdoor coil = 15°F. • CChhaarrggiinngg aatt ootthheerr ccoonnddiitti ...

Heater size (MBh) 0-2000' 3000' 4000' 5000' 6000' 7000' 8000' 9000' 10000' 250 1.75 mm #51 #51 #51 #52 #52 #52 #53 #53 350 #49 #50 #50 #51 #51 #51 #52 #52 #52 500 #50 #51 #51 #51 #52 #52 #52 #53 #53 850(a) 1.65 mm #52 #53 #53 #53 #53 #54 #54 #54 1200 1.9 mm #49 #49 #50 #50 #50 #51 #51 #52 Note: Orifice sizes required to reduce input ratings by 4% per every 1000’ above 2000’ per the National Fuel Gas Code Z223.1. (a) 850,000 Btu/Hr at Sea Level input is 737,000 Btu/Hr IInnssttaallllaattiioonn ...

transit, perform inspection immediately upon receipt of the unit. Exterior Inspection If the job site inspection reveals damage or material shortages, file a claim with the carrier immediately. Specify the type and extent of the damage on the bill of lading before signing. Notify the appropriate sales representative. IIm mppoorrttaanntt:: Do not proceed with installation of a damaged unit without sales representative’s approval. • Visually inspect the complete exterior for signs of shipping ...

demands of the occupants. UUnnooccccuuppiieedd OOppeerraattiioonn: The IntelliPak unit is typically shut down and is not providing temperature control to the normal occupied setpoints. No ventilation is required or provided. Temperature control is determined by energy conservation and building protection thresholds. OOccccuuppiieedd BByyppaassss OOppeerraattiioonn: The IntelliPak unit is temporarily in an Occupied state for some period of time and will automatically return to unoccupied operation when the bypass timer expire ...