Toro 25520 Installation Instructions Manual

Rear Steering Indicator Kit RT600 Traction Unit Model No. 25520 Model No. 25520E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Prepare the machine. Rear-steering indicator decal (125-6697) 1 2 Steering warning decal (125-8471) 1 Apply the decals to the steering-indicator plate. 3 No parts required – Remove the right fender from the machine. Position-indicator cable 1 Locknut (M10) 1 Ball joint 1 Plate 1 Flange nut (3/8 inch) 1 Clamp (3/8 x 3/8 inch) 1 4 Hex-head screw (3/8 x 1 inch) 1 Install the position-indicator cable. 5 No parts required – Install the right fender onto the machine. Locknut (M10) 2 6 Position-indicator pointer 1 Install the position-indicator pointer. © 2014—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved *3386-813* A

No Parts Required Procedure 1. Move the machine to a level surface. 2. Set the parking brake and lower the attachments to the ground 3. Shut off the machine and remove the key. 4. Use a jack with a capacity of 2,494 kg (5,500 lb) to raise the machine at the rear axle. WARNING Raising the unit relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury or death. Do not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support. 5. Use jack stands with a capacity of 2,494 kg (5,500 lb) to support the back of the machine. 6. Remove the right, rear wheel. 2 Applying the Decals to the Steering-indicator Plate Parts needed for this procedure: 1 Rear-steering indicator decal (125-6697) 1 Steering warning decal (125-8471) Procedure Apply the decals to the steering-indicator plate as shown in Figure 1. Figure 1 1. Steering-indicator plate 3. Steering warning decal (125-8471) 2. Rear-steering indicator decal (125-6697) 2

from the Machine No Parts Required Procedure 1. Remove the 2 bolts and locknuts from the side of the back ROPS plate (Figure 2). Figure 2 1. Bolts and locknuts 3. Back ROPS plate 2. Right fender 2. Remove the 2 bolts and locknuts from the bottom of the right fender (Figure 2). 3. Remove the bolt and locknut from the front ROPS plate (Figure 3). Figure 3 1. Right fender 3. Front ROPS plate 2. Bolt and locknut 4. Remove the right fender from the machine (Figure 3). 4 Installing the Position-indicator Cable Parts needed for this procedure: 1 Position-indicator cable 1 Locknut (M10) 1 Ball joint 1 Plate 1 Flange nut (3/8 inch) 1 Clamp (3/8 x 3/8 inch) 1 Hex-head screw (3/8 x 1 inch) Procedure 1. Insert one end of the position-indicator cable through the opening in the front ROPS plate into the opening in the steering-indicator plate (Figure 4). 3

2. Secure the position-indicator cable to the back ROPS plate with the flange nut (3/8 inch), clamp (3/8 x 3/8 inch), and the hex-head screw (3/8 x 1 inch) as shown in Figure 5. Figure 5 1. Position-indicator cable 4. Hex-head screw (3/8 x 1 inch) 2. Flange nut (3/8 inch) 5. Back ROPS plate 3. Clamp (3/8 x 3/8 inch) 3. Route the other end of the position-indicator cable through the opening in the rear-steering mount on the rear axle (Figure 6). Figure 6 1. Position-indicator cable 2. Rear-steering mount 4. Secure the position-indicator cable to the rear axle with the plate, locknut (M10), and the ball joint (Figure 7). Figure 7 1. Position-indicator cable 3. Plate 2. Ball joint 4. Locknut (M10) 4

onto the Machine No Parts Required Procedure 1. Align the right fender with the holes where the 5 bolts and the 5 locknuts were removed in 3 Removing the Right Fender from the Machine (page 3). 2. Install the 5 bolts and the 5 locknuts into the back ROPS plate, front ROPS plate, and the right fender (Figure 2 and Figure 3). 6 Installing the Position-indicator Pointer Parts needed for this procedure: 2 Locknut (M10) 1 Position-indicator pointer Procedure 1. Insert the position-indicator cable through the side of the steering-indicator plate (Figure 8). Figure 8 1. Position-indicator pointer 3. Position-indicator cable 2. Steering-indicator plate 4. Locknuts (M10) 2. Install 2 locknuts (M10) and the position-indicator pointer onto the position-indicator cable (Figure 8). 3. Position the position-indicator pointer to the middle of the opening in the steering-indicator plate (Figure 9). Figure 9 1. Steering-indicator plate 3. Position-indicator pointer 2. Opening for the position-indicator pointer 5

Center the rear wheels from left to right by adjusting the ball joint and the locknut at the end of the position-indicator cable until the indicator at the operator’s position shows that the wheels are straight (Figure 10). Figure 10 1. Position-indicator cable 3. Locknut (M10) 2. Ball joint 6