TOORX BRX50 Instruction

with 4 bolts (E-1), 4 nuts (E-4) and 4 washers (E-3). 5

seat post (D) into the support tube, tighten the knob. Step 3 Assemble the saddle (D-3) onto the slider set (D-5) with three nuts and washers, fix the saddle. Assemble the slider set with the seat post with Knob (D-1) and flat washer (D-2). ASSEMBLY INSTRUCTIONS 6

washers (E-3). Connect the tension control upper (C-2) & lower (G-4), connect the sensor cable upper (C-1) & lower (G-3). Insert handle bar post (C) onto the support tube, tighten with four screws and washers. Step 5 Put the handle bar (B) into the metal bracket, make the hand pulse cable through the hole on handle bar post, cover the bracket with the plastic cover, use flat washer (B-5), spring washer (B-6), bushing (B-7) and T-knob to fix the handle bar as the right drawing. 7

computer and handle bar (A-2&B-3), connect the sensor cables (A-1&C-1), fix the computer onto the metal plate with two screws (A-3). Step 7 Assemble the left hand pedal (M-L) and the right hand pedal (M-R) to the hand crank. 8

1PC A-3 Screw 2PCS B Handle bar set 1SET B-1 End cap 2PCS B-2 Handle bar foam 2PCS B-3 Hand pulse cable 1PC B-4 Hand grip 2PCS B-5 Flat washer 1PC B-6 Spring washer 1PC B-7 Bushing 1PC B-8 Handle bar cover 1PC B-9 T-knob 1PC C Handlebar post set 1SET C-1 Sensor cable (upper) 1PC C-2 Tension controller(Upper) 1PC D Seat post 1PC D-1 Knob for seat 1PC D-2 Flat washer 1PC D-3 Saddle 1PC D-4 End cap 2PCS D-5 Slider 1PC D-6 Screw 1PC D-7 Flat washer 5PCS D-8 Nylon nut 6PCS E Front stabilizer 1PC E-1 Carriage screw M8*65 4PCS E-2 Front end cap 2PCS E-3 Semicircle washer 8PCS E-4 M8 nut 4PCS F Rear stabilizer 1PC F-1 Rear end cap 2PCS G Main frame 1PC G-1 Screw 1PC 9

1PC G-4 Tension control (lower) 1PC G-5 Seat post knob 1PC G-6 Plastic sleeve 1PC H Plastic pully 1PC H-1 Crank 1PC H-2 Belt 1PC H-3 Right thread 1PC H-4 Ball retainer 2PCS H-5 Bottom bracket 2PCS H-6 Left thread 1PC H-7 Have tooth washer 1PC H-8 Hex. nut 1PC I Flywheel 1PC I-1 Flywheel bearing 1PC I-2 6900 bearing 1PC I-3 Bushing 1PC I-4 Nut 5PCS I-5 6000 bearing 1PC J Idle set 1SET J-1 Idle wheel 1PC J-2 Bushing 1PC J-3 Hex. screw 1PC J-4 Spring 1PC K Magnetic set 1SET K-1 Screw 1PC K-2 Magnetic 7PCS K-3 Spring 1PC L-L Chain cover (left) 1PC L-R Chain cover (right) 1PC L-1 Cover for crank 2PCS L-2 Screw 5PCS L-3 Screw 4PCS M-L Pedal (left) 1PC M-R Pedal (left) 1PC 10

Can to proceed the data establish for “TIME””DISTANCE””CALORIES” Hold two seconds to reset all of the values to zero. Automatically scan through each mode in sequence every 6 seconds. The display loop is TIME- SCAN-DISTANCE-CALORIE-SPEED on the main screen. Displays current training SPEED, the maximum is 99.9km/ml,it always displays. Accumulates total working time from 00:00 up to 99:59. Accumulates training distance from 0.00 to the maximum 99.99km/ml with each increment 0.01km/ml. Accumulates calories consumption during training from 0 to the maximum 9999 cal with each increment 1 cal. Press the MODE key until the pointer advance to PULSE. User’s current heart rate will be displayed in beats per minute. Place the palms of your hands on both of the contact pads (or put ear-clip to ear),and wait for 30 seconds for most accurate reading. ODO Press the MODE key until the pointer advance to ODOMETER.The total accumulated distance will be shown. NOTE 1. Without any signal been transmitted into the monitor for 4 minutes, the LCD display will shut off automatically, and all function values will be kept. You may press mode or start pedaling to have the monitor power on again. 2. If improper display on monitor, please re-install batteries to have a good result. 3. Battery spec: 1.5v um-3 or AA(2pcs). 12

15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - [email protected]