Teldat Connect-KFPlus Installation Manual

Teldat S.A. Manual Teldat Connect-KFPlus 1

Teldat S.A. offers no warranty whatsoever for information contained in this manual. Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv- ery, supply or use of this manual. Manual Teldat S.A. 2 Teldat Connect-KFPlus

I Related Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1 About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.4 What is in this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.5 What is not in this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.6 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.7 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2 Teldat Connect-KFPlus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1.2 Hardware Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 3 Components and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1.2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1.3 Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1.4 Underside Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Mounting an Anti-Theft Security Cable. . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.3 Rack installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.3.1 Standalone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.3.2 Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.4 Plug-in Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.5 Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.5.1 Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.6 RST Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.6.1 Rebooting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.6.2 Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.7 Data connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.7.1 4-port Ethernet switch Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.7.2 WAN Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.7.3 WWAN Antenna Connection (Cell connector). . . . . . . . . . . . . . . . . . . . . . . 15 Teldat S.A. Table of Contents Teldat Connect-KFPlus i

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.7.5 Wireless LAN internal antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.7.6 Connecting for Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.8 Installing the SIM card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chapter 4 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.1 Manufacturer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.2 Risk identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.3 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.4 WEEE Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.5 REACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.6 Power Usage and Energy Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.7 PSU Energy Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.8 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.9 CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.10 National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.11 Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.12 Intended use of the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Appendix A Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 A.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 A.2 Updating the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 A.3 Connecting to the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 A.3.1 Connecting using the local console (Aux connector) . . . . . . . . . . . . . . . . . . . . 21 A.4 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 A.4.1 LAN Connector (Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 A.4.2 WAN Base-T Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 A.4.3 WAN SFP Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 A.4.4 WWAN Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 A.4.5 GPS Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 A.4.6 Configuration Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A.4.7 Power Supply Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A.5 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A.5.1 Hardware Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A.5.2 LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A.5.3 WAN Base-T Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 A.5.4 WAN SFP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 A.5.5 Wireless WAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table of Contents Teldat S.A. ii Teldat Connect-KFPlus

25 A.5.7 Wireless LAN Interface (Radio 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 A.5.8 Wireless LAN Interface (Radio 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A.5.9 Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A.5.10 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A.5.11 Dimensions and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 A.5.12 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Appendix B CE Radio Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 B.1 WI-FI specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Teldat S.A. Table of Contents Teldat Connect-KFPlus iii

Teldat Dm704-I Configuration and Monitoring Teldat Dm748-I Software Updating bintec Next Generation WLAN Manual Teldat S.A. Related Documents Teldat Connect-KFPlus 1

This is the installation manual for the Teldat Connect-KFPlus router and contains information on how to correctly in- stall the device in a working environment. 1.1 Supported Devices The information provided in this installation manual only applies to the Teldat Connect-KFPlus router. Note The Wi-Fi version includes an embedded bintec WE2022ac access point. 1.2 Who should read this manual? This manual should be read by the support personnel who need to configure, maintain and monitor the device. 1.3 When should this manual be read? Read this guide as soon as you are ready to familiarize yourself with the device and its components. This manual will help you understand your new device in greater depth. 1.4 What is in this manual? This installation manual contains the following information: • A description of the available features in the Teldat Connect-KFPlus router. • Technical specifications. • Power supply requirements. • Elements that can be connected when the router is operating. • How to install and uninstall the modules and power sources. • A description of the device LEDs and connectors. • Troubleshooting. 1.5 What is not in this manual? This manual does not contain information about the device software or its configuration. For information on how to configure this device, please see the relevant protocol manuals found on the Teldat website: http://www.teldat.com Note 1.6 How is the information organized? Each chapter focuses on a specific part of the hardware and its components. All descriptive and technical specifica- tions, as well as information on a given component, can be found in the relevant chapter. 1 About This Guide Teldat S.A. 2 Teldat Connect-KFPlus For more information on the latter, please refer to manual "bintec Next Generation WLAN". For information on how to configure the bintec WE2022ac WiFi access point, refer to manual "bintec Next Generation WLAN".

Teldat S.A. offers technical support. Device software can be upgraded on a regular basis for maintenance purposes and when new features are developed. Contact information: Web: http://www.teldat.com - Email: [email protected] Tel.: +34 918 076 565 - Fax: +34 918 076 566 Teldat S.A. 1 About This Guide Teldat Connect-KFPlus 3

2.1 Characteristics 2.1.1 Power Supply 2.1.2 Hardware Monitoring The LEDs on the front panel are used to monitor the hardware in the Teldat Connect-KFPlus router. These LEDs provide visual information on the state of the device and reference the condition of the hardware components, indic- ating whether or not there is connectivity, data flow, etc. For further information on the LED panel, please see Components on page 5. 2 Teldat Connect-KFPlus Teldat S.A. 4 Teldat Connect-KFPlus For further information on the different Teldat Connect-KFPlus power supplies, please see Components and Power Supply on page 5, Power Source on page 11.

The following chapter provides detailed information on the chassis of the Teldat Connect-KFPlus router and its components. This information includes: • Components. • Information on assembly. • Power supply. • RST button. • Data connection. • SIM card installation. • Embedded access point. 3.1 Components 3.1.1 Front Panel The following figure shows the front panel. Fig. 1: Front Panel of the Teldat Connect-KFPlus device The front panel elements are as follows: FRONT PANEL ELEMENTS Item Description A LED panel. The LED panel provides information on the status of the components (indicating whether they are active or not) and on network activity. LEDs LED Definition Status Indication Power Power / Switch On-Off Off -> No power through PSU. On -> Powered through PSU. Status General Status / Default Configuration Process Off -> System off. Red -> Error, component operating incorrectly. Green -> System initialized and operating. Amber (blink) -> Default configuration. WAN-1 Base-T / SFP Off -> No link or not used. Green -> Link (1G). Blinking: traffic activity. Amber -> Link (<1G). Blinking: traffic activity. Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 5

WAN-2 Base-T / SFP Off -> No link or not used. Green -> Link (1G). Blinking: traffic activity. Amber -> Link (<1G). Blinking: traffic activity. Red -> Error. Interface failure. This interface is disabled by default and can be enabled by means of a license. LAN Switch LAN switch interface activity Green -> connected (all connected ports at 1G). Blinking: connec- tion data activity. Amber -> connected (at least one port at <1G). Blinking: connec- tion data activity. Red -> Disconnected. Off -> Interface off. WLAN-1 (Depending on the model) Access Point 2.4 GHz radio Off -> Radio module and/or SSIDs inactive. Red -> No connection, or disabled (shutdown). Amber -> Enabled, but no associated STAs. Green -> Connected. Blinking: connection data activity. WLAN-2 (Depending on the model) Access Point 5 GHz radio Off -> Radio module and/or SSIDs inactive. Red -> No connection, or disabled (shutdown). Amber -> Enabled, but no associated STAs. Green -> Connected. Blinking: connection data activity. Cell Status Not used on this router. RSSI. Coverage indication Not used on this router. SIM-1 Not used on this router. SIM-2 Not used on this router. GPS (Depending on the model) GPS Status Not used on this router. 3 Components and Power Supply Teldat S.A. 6 Teldat Connect-KFPlus

3.1.2 Rear Panel The following figure shows the rear panel. Here you will find most connectors belonging to the Teldat Connect- KFPlus router. Fig. 2: Rear panel The following table provides information on each connector, as well as a description: Rear panel elements Item Description A Function. B RST. Reset button. For further information on how the reset button works, please see RST Button on page 13. C 4-port Gigabit Ethernet switch. For more information about the LAN interface, refer to: - 4-port Ethernet switch Connections on page 14 - LAN Connector (Switch) on page 22 - LAN Interface on page 24 D Eth WAN-1 Base-T. WAN Gigabit Ethernet. For more information about the WAN interface, refer to: - WAN Connections on page 14 - WAN Base-T Connector on page 23 - WAN Base-T Interface on page 25 E Eth WAN-1 SFP. For more information about the SFP interface, refer to: - WAN Connections on page 14 - WAN SFP Connector on page 23 - WAN SFP Interface on page 25 F Eth WAN-2 Base-T. WAN Gigabit Ethernet. This interface is disabled by default and can be enabled by means of a license. For more information about the WAN interface, refer to: - WAN Connections on page 14 Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 7

- WAN Base-T Interface on page 25 G Eth WAN-2 SFP. This interface is disabled by default and can be enabled by means of a license For more information about the SFP interface, refer to: - WAN Connections on page 14 - WAN SFP Connector on page 23 - WAN SFP Interface on page 25 H Aux. provides access to the Teldat Connect-KFPlus local console for configura- tion and monitoring purposes. For more information about the Aux connector, refer to: - Connecting for Configuration on page 15 - Configuration Connector on page 24 - Configuration Interface on page 27 I SIM Card 1-2. These slots are not used on this router. J On/Off switch. K Power source connection (PSU). Refer to Power Source on page 11 for more information about Power connection and Power Supply on page 27 for power specifications applicable to theTeldat Connect-KFPlus device. L LED S (Status). Refer to LEDs on page 5 for more information. M LED PWR (Power). Refer to LEDs on page 5 for more information. N Functional earthing. Usually disconnected. O Cell antenna connectors. They are not used on this router. P GPS antenna connector. This is not not used on this router. In addition to the foregoing, the rear panel also has LEDs linked to the Switch Ethernet interfaces. 3.1.2.1 LEDs The following figure shows the router's Ethernet switch LED indicators: Fig. 3: Switch LEDs 3 Components and Power Supply Teldat S.A. 8 Teldat Connect-KFPlus

LED Description Yellow Connected to 10 M: - Steady: Not transferring data. - Blinking: Transferring data. Yellow + Green Connected to 100 M: - Steady: Not transferring data. - Blinking: Transferring data. Green Connected to 1000 M: - Steady: Not transferring data. - Blinking: Transferring data. None The interface is either unavailable, not installed, or not registered. The following figure shows the router's WAN LED indicators (only for the Base-T connector): Fig. 4: WAN LEDs WAN LED indicators LED Description Yellow Connected to 10 M: - Steady: Not transferring data. - Blinking: Transferring data. Yellow + Green Connected to 100 M: - Steady: Not transferring data. - Blinking: Transferring data. Green Connected to 1000 M: - Steady: Not transferring data. - Blinking: Transferring data. None Interface is either unavailable, not installed, or not registered. 3.1.3 Side Panels Two antenna connectors are located on the side panels. Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 9

The connectors are as follows: Side panel connectors Item Description A Aux 2 and Aux 3 connectors. These are not used on this router. 3.1.4 Underside Panel The following elements are located on the underside panel: Fig. 6: Underside panel UNDERSIDE PANEL ELEMENTS Item Description A Adhesive rubber feet (these are not required for rack mounting). 3.2 Mounting an Anti-Theft Security Cable Teldat Connect-KFPlus devices have been equipped with a standard Kensington security slot to which a security cable can be attached. The T-bar lock of the security cable allows the device to be attached to an anchor point, thus preventing potential thefts. The security slot is located on the rear panel of the housing, as shown in the following figure: 3 Components and Power Supply Teldat S.A. 10 Teldat Connect-KFPlus

3.3 Rack installation The Teldat Connect-KFPlus device can be installed in a 19” rack. The necessary strips and screws are not provided by default and must be acquired separately. Both strips are attached to the device by means of 5 screws, as shown in the following figure: Fig. 8: Rack anchor bolts Note The device is designed to allow brackets to be attached to the front or rear of the router chassis. 3.3.1 Standalone Teldat Connect-KFPlus devices can be placed as standalone on a flat, stable surface. The adhesive rubber feet must be stuck to the underside panel to prevent the router from sliding. Make sure there is enough space around the router (for ventilation purposes) and check that the power cord and data cables can easily reach it. 3.3.2 Wall mounting The Teldat Connect-KFPlus cannot be mounted on a wall. 3.4 Plug-in Modules The Teldat Connect-KFPlus does not have plug-in modules. 3.5 Power Source The Teldat Connect-KFPlus router is powered through an external AC/DC power adapter. Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 11

Workplace conditions. Main characteristics • Avoid humid and/or dusty locations. • Direct exposure to sunlight and other heat sources should be avoided. The device should not be placed amongst papers, magazines or other elements that could hinder natural air circulation. • The device should not be placed close to strong electromagnetic fields (such as speakers, engines, etc.). • Knocks and/or strong vibrations should be avoided during transport, operation and storage. Warning 3.5.1 Power Source To avoid electric shocks, residual current circulation and other unwanted effects that affect communications, the fol- lowing is recommended: Warning For safety and EMC purposes, the external power supply must be connected to a grounded power out- let. Note We recommend plugging all interconnected communication devices to the same grounded power out- let. 3.5.1.1 Connecting • Make sure the on/off power supply switch is in the OFF position (0). • Make sure the power supply is NOT connected to the mains or to the device. • Connect all data cables. • Connect the external adapter power cable to the device. • Connect the adapter power cable to the main supply (wall socket). • Put the device's on/off power supply switch in the ON position (1). 3.5.1.2 Disconnecting • Put the on/off power supply switch in the OFF position (0). • Disconnect the adapter power cable from the main supply (wall socket). • Remove the power supply cable from the device. • Disconnect the data cables. 3 Components and Power Supply Teldat S.A. 12 Teldat Connect-KFPlus The electric current in power cables, telephone lines and communication cables is dangerous. To pre- vent electric shocks, before installing, handling or opening the equipment covers, connect and discon- nect the cables following the steps set forth in Connecting on page 12 and Disconnecting on page 12. To connect the power supply to the device, please follow the steps set out in Connecting on page 12.

The different RST button features are described below. Fig. 9: RST button 3.6.1 Rebooting the device Once the device is operating normally, pressing the RST button will force a restart. Note It will also force a restart of the embedded access point (if present). 3.6.2 Default Configuration The RST button allows you to boot the device with its default configuration (including the embedded access point, if present). To do so, follow these steps: • With the device switched off, press and hold the RST button down while you turn the router on using the ON/OFF switch (1). • The PWR LED (green) will light up and LED 'S' will begin to blink (amber). It will carry on blinking for 10 seconds. • To boot the device with the default configuration, release the RST button while LED 'S' is still blinking (i.e. before the 10-second period expires). The router has an embedded access point. The default configuration looks like a template for a Wi-Fi configuration. It includes all the necessary elements to deploy a very basic Wi-Fi network. To activate this configuration, all you need to do is to enter the enable command at the WNMS feature menu. This configuration will provide two Wi-Fi networks: test_ssid_1 and test_ssid_2. The first one is placed in the 2.4 GHz band and the second one in the 5 GHz band. The password for both networks matches their ssid name. The DHCP server configuration is divided into two parts. The first one focuses on giving an address to the embedded access point, while the second strives to give an address to the Wi-Fi clients that connect to the access point. A bridge is installed to separate the traffic belonging to Wi-Fi clients from access point communications. Two VLANs are configured for this purpose. The communication with the embedded access point is carried out via a separate port in the switch interface. This port is named "wlan" or listed as port 5. The router's default configuration establishes the following access IP and mask address: • IP address: 192.168.0.1 • IP mask: 255.255.255.0 The embedded access point's default configuration establishes the following IP and mask address: • IP address: DHCP client with no. 192.168.100.150/24 as default Note Some devices leave the factory with customized settings. This personalization means your router's de- fault configuration (and that of the embedded access point, where applicable) may be different from the one shown above. Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 13

The Teldat Connect-KFPlus router has the following data connections. 3.7.1 4-port Ethernet switch Connections The Teldat Connect-KFPlus router incorporates a 4-port 10/100/1000 Base-T switch with automatic MDI/MDIX to connect to a local area network (LAN). Please pay careful attention to the labeling to avoid mistaking this switch for other types of ports: Fig. 10: LAN switch ports Note Only the LAN 1 connector is available during booting and in BIOS mode. 3.7.2 WAN Connections The Teldat Connect-KFPlus has 4 Ethernet interfaces for WAN connection. These ports have 2 connectors - SFP for an optical link and RJ45 for a 10/100/1000 Base-T link - but they cannot work simultaneously. These interfaces are totally independent from the switch and are handled as every other interface. Please pay careful attention to the labeling to avoid mistaking these ports for other types of ports: Fig. 11: WAN connectors Note WAN connectors do not work during booting and in BIOS mode. 3.7.2.1 Laser information Choose SFP transceivers that meet the following regulations • Class 1 • IEC/EN60825-1:2007 2nd Edition or a later one, European standard • FCC 21 CFR Chapter 1, Subchapter J (in accordance with FDA and CDRH re- quirements) • Application of CE marking in accordance with the 2014/30/EU EMC Directive and the 2014/35/EU Low Voltage Directive • UL and/or CSA registered component for North America • 47 CFR Part 15, Class A 3 Components and Power Supply Teldat S.A. 14 Teldat Connect-KFPlus

PRODUCT. The SFP modules to be installed in the card socket should be class 1 devices that comply with the IEC/ EN 60825-1:2007 standard. 3.7.3 WWAN Antenna Connection (Cell connector) The Teldat Connect-KFPlus router has two SMA connectors in the rear panel and two SMA connectors in the side panel that are not used on this router. 3.7.4 Connecting the GPS antenna The Teldat Connect-KFPlus has an SMA connector in the rear panel that is not used on this router. 3.7.5 Wireless LAN internal antennas The Teldat Connect-KFPlus has two integrated antennas for an internal Wireless LAN module covering both the 2.4 GHz and 5 GHz bands. Fig. 12: Antenna connectors 3.7.6 Connecting for Configuration The Teldat Connect-KFPlus has a RJ45 female connector on the front panel (labeled "Aux.") that provides access to the device's local console For further information, please see Connecting to the device on page 21. Fig. 13: Aux. Connector 3.8 Installing the SIM card The Teldat Connect-KFPlus router does not use SIM cards. Teldat S.A. 3 Components and Power Supply Teldat Connect-KFPlus 15

4.1 Manufacturer Information Brand Teldat Manufacturer Teldat S.A. Country Spain Postal Address Isaac Newton, 10 Parque Tecnológico de Madrid, 28760 Tres Cantos, Madrid, Spain International Phone +34 91 807 65 65 4.2 Risk identification WARNING: Signal word used to designate a potentially dangerous situation that may cause severe injuries or death if not avoided. 4.3 Safety Warnings                              !       "              #               $           %       &$    $         $                Connecting   '(  Disconnecting   '(  &   )   ) %$ %   &    * "& & !  $  )    +  $  ,    -      .     /  0      1  # 2          #$      3 #         #    4   $     $             $                  56 7  5 7 8    "96  $  :                / )  %  "90%;   :   !        ) & 4 Compliance Teldat S.A. 16 Teldat Connect-KFPlus

     #          1 <                      61/)) ' 1/)"< 4<=*6  )84        &    '         +"6>" ?@A(B%'C(@@D   1    &   +      1/)"<4<=*. "< .1/))" ' )84%9$    .      $   .%'%  E   +"6>" ?@A(B%'C(@@D   <  #             #  4  1/)"< 61/)" ' 1 # )84       &   F         61/)" '      +"6>" ?@A(B%'C(@@D 4.4 WEEE Information The waste container symbol with the >X< indicates that the device must be dis- posed of separately from normal domestic waste at the end of its useful service life. Please use an appropriate waste disposal facility. Das auf dem Gerät befindliche Symbol mit dem durchgekreuzten Müllcontainer bedeutet, dass das Gerät am Ende der Nutzungsdauer bei den hierfür vorgese- henen Entsorgungsstellen getrennt vom normalen Hausmüll zu entsorgen ist. El símbolo del contenedor con la cruz, que se encuentra en el aparato, significa que cuando el equipo haya llegado al final de su vida útil, deberá ser llevado a los centros de recogida previstos, y que su tratamiento debe estar separado del de los residuos urbanos. 4.5 REACH In compliance with the REACH Candidate List, the delivered product and product packaging do not contain chemical substances above a concentration limit of 0.1% weight by weight (w/w). This declaration will be updated whenever any changes occur or other chemical substances are added to the REACH Candidate List. Information is currently provided to consumers upon request. 4.6 Power Usage and Energy Efficiency This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and automatically switches to a power-saving Network Standby mode when no packets have been transmitted for 10 minutes (set by default). It can also be turned off through a power switch to save energy when it is not needed. Network Standby: 6.5W All interfaces can be shut down individually: Teldat S.A. 4 Compliance Teldat Connect-KFPlus 17

learn how to disable each interface. • Wi-Fi interfaces: refer to the "bintec Next Generation WLAN Manual" to learn how to disable each of the radio in- terfaces. 4.7 PSU Energy Efficiency Model A0403TD Manufacturer Name Atech OEM Inc. Manufacturer Address 2F No. 135 Lane 235 Baociao Rd, Sindian City Taipei County, 23145 TW. Input Voltage 100-240 Vac Input AC frequency 50-60 Hz Output voltage 12.0 V Output current 3.34 A Output power 40.0 W Average active efficiency 88.8% Efficiency at low load (10%) 84.2% No-load power consumption 0.09 W 4 Compliance Teldat S.A. 18 Teldat Connect-KFPlus According to Commission Regulation (EU) 2019/1782, laying down ecodesign requirements for external power sup- plies pursuant to Directive 2009/125/EC of the European Parliament and of the Council and repealing Commission Regulation (EC) No 278/2009, the instruction manuals for end-users shall include the following information:

English (EN) Hereby, Teldat S.A. declares that radio equipment Teldat Connect-KFPlus com- plies with: Directive 2014/53/EU (RED) Directive 2009/125/EC (ErP) Directives 2011/65/EU and 2015/863/EU (RoHS) of the European Parliament and of the Council. German (DE) Deutsch Hiermit erklärt Teldat S.A. die Übereinstimmung des Geräts Teldat Connect- KFPlus mit: Richtlinie 2014/53/EU (RED) Richtlinie 2009/125/EG (ErP) Richtlinien 2011/65/EU und 2015/863/EU (RoHS) des Europäischen Parlaments. Spanish (ES) Español Por la presente, Teldat S.A. declara que el tipo de equipo radioeléctrico Teldat Connect-KFPlus es conforme con: Directiva 2014/53/UE (RED) Directiva 2009/125/CE (ErP) Directivas 2011/65/UE y 2015/863/UE (RoHS) del Parlamento Europeo y del Consejo. The EC declaration of conformity and additional product documentation can be accessed here: http://www.teldat.com/conformity 4.9 CE Marking This equipment is in conformity with CE procedures and marking. 4.10 National Restrictions In accordance with Article 10 of Directive 2014/53/EU, we inform you that national restrictions and requirements may apply for authorization purposes. These can evolve over time. Teldat S.A. recommends that you check with local au- thorities what the latest status of national regulations is. This product is supplied with antennas so as to fulfill local regulations. Do not choose other antennas. To comply with power limits and RF exposure requirements, the antennas used for this transmitter must be installed so that people keep a separation distance of, at least, 20 cm. Teldat S.A. 4 Compliance Teldat Connect-KFPlus 19

To find out more about operating frequencies, and the maximum power transmitted in the frequency bands in which the radio equipment operates, see appendix WI-FI specifications on page 29. 4.12 Intended use of the equipment The Teldat Connect-KFPlus device can be deployed as a Customer Premises Equipment (CPE) in enterprise branch offices or in environments managed by the service provider. This product must only be used indoors. 4 Compliance Teldat S.A. 20 Teldat Connect-KFPlus

A.1 Troubleshooting The following table can help you solve problems when installing the device. If you cannot resolve the issue, please contact your dealer for more information. Symptom Solution None of the LEDs lights up on the router. Check the power supply to the router (power source, ON/OFF switch, main power outlet). You have forgotten the router's access password. Ignore the configuration through the RST button (as explained in the relevant sec- tion). The LAN switch LED never lights up in green. Check the Ethernet cable and the connection to the network. The Eth WAN LED never lights up in green. Check the Ethernet cable and the connection to the network. Check the appropriate license is available for use. The Wi-Fi LED never lights up in green. Check the router configuration and that of the remote station(s). Check the appropriate license is available for use. A.2 Updating the software The Teldat Connect-KFPlus router can be updated to new versions. Please contact your dealer for further details on new releases. There are several ways to update a Teldat router. For further information, please see manual: “Teldat Dm748-I Soft- ware Updating”. The software required to update Teldat routers is supplied in a format known as distribution, which contains all the files needed to update your device and in-depth information on their content. The embedded access point (if available) can also be updated to new versions. Please contact your dealer for further details on new releases for the embedded access point. A.3 Connecting to the device A.3.1 Connecting using the local console (Aux connector) The Teldat Connect-KFPlus router has a RJ45 female connector on the front panel, known as Aux, which provides access to the device's local console. Fig. 14: Aux Connector To configure this, you must connect the Aux port to an asynchronous terminal (or to a PC with terminal emulation). Teldat S.A. Technical Information Teldat Connect-KFPlus 21

- Speed: 9600 bps. - Eight data bits. - One stop bit. - No parity bit. - No type of flow control. Connection to the configuration port can be carried out using the the RJ45 connector cable, supplied with the device, and an RJ45 female-DB9 female adapter (also provided). Fig. 15: Connecting for Configuration For further information, please see manual: “Teldat Dm704-I Configuration and Monitoring”. A.4 Connectors A.4.1 LAN Connector (Switch) RJ45 LAN RJ45 PIN FE Signals GE Signals 1 2 3 4 5 6 7 8 BI-DA+ BI-DA- BI-DB+ -- -- BI-DB- -- -- BI-DA+ BI-DA- BI-DB+ BI-DC+ BI-DC- BI-DB- BI-DD+ BI-DD- Technical Information Teldat S.A. 22 Teldat Connect-KFPlus

RJ45 WAN RJ45 PIN FE Signals GE Signals 1 2 3 4 5 6 7 8 BI-DA+ BI-DA- BI-DB+ -- -- BI-DB- -- -- BI-DA+ BI-DA- BI-DB+ BI-DC+ BI-DC- BI-DB- BI-DD+ BI-DD- A.4.3 WAN SFP Connector SFP Standard SFP connector A.4.4 WWAN Connector Devices equipped with this interface have up to four SMA female connectors installed. SMA Female PIN ANT Internal External RF in/out GND A.4.5 GPS Connector Devices equipped with this interface have one SMA female connector installed. SMA Female PIN ANT Internal External RF in/out GND Teldat S.A. Technical Information Teldat Connect-KFPlus 23

RJ45 CONFIGURATION RJ45 PIN CONF 1 2 3 4 5 6 7 8 -- RxD GND -- -- GND TxD -- A.4.7 Power Supply Connector Jack 5.5/2.5mm PIN Internal -> POSITIVE External -> NEGATIVE A.5 Technical Specifications A.5.1 Hardware Architecture PROCESSORS Freescale QorIQ. MEMORY 256 MBytes in SDRAM. STORAGE UNIT FLASH Memory (32 MBytes). A.5.2 LAN Interface PROTOCOLS Ethernet (802.3). PORTS 4 port switch managed with MDI/MDX auto-detection. SPEED 10/100/1000 Mbps (Base-T). CONNECTOR RJ45 female. Technical Information Teldat S.A. 24 Teldat Connect-KFPlus

STANDARDS Ethernet (802.3). SPEED 10/100/1000 Mbps (Base-T). CONNECTOR RJ45 female. A.5.4 WAN SFP Interface STANDARDS 802.1Q (VLAN). 1000-Base-X. MSA and SFF 8472 compliant. SPEED 1000 Mbps full duplex. TYPES LX/LH (single-mode 1310 nm). SX (multi-mode 850 nm). ZX (single-mode 1550 nm). CONNECTOR Standard SFP connector. A.5.5 Wireless WAN interface WWAN Standard/Bands Not used by the router. CONNECTOR Five SMA connectors, not used by the router. SIM Slots 2 Mini-SIM (2FF), not used by the router. ANTENNA Not used by the router. A.5.6 GPS interface STANDARDS Not used by the router. GNSS Not used by the router. SATELLITE CHANNELS Not used by the router. CONNECTOR SMA female. ANTENNA Not used by the router. Teldat S.A. Technical Information Teldat Connect-KFPlus 25

WLAN standards 802.11b; 802.11g; 802.11n (MIMO 2x2) 2.4 GHz Frequency bands 2.4 GHz in- door/outdoor (EU) 2.4 GHz Indoor/Outdoor (2412-2484 MHz) max. 100 mW EiRP (20dBm). WLAN modes 2.4 GHz Operation: 802.11b only; 802.11g only; 802.11b/g; 802.11b/g/n; 802.11g/n. Modulation Techniques OFDM: BPSK, QPSK, DBPSK, DQPSK, 16-QAM, 64-QAM, 256-QAM. Automatic Rate Selection (ARS) Available. Transmission rate Automatic. Data rates 802.11b/g: 11, 5.5, 2 and 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation). 802.11n (20 MHz channel bandwidth): MCS0-15 allow up to 150 Mbps PHY rate at 20 MHz channel bandwidth, 2 streams, short guard interval. Up to 173.3 Mbps (QAM-256) with clients that support QAM-256. 802.11n (40 MHz channel bandwidth): MCS0-15 allow up to 300 Mbps PHY rate at 40 MHz channel bandwidth, 2 streams, short guard interval. Up to 400 Mbps (QAM-256) with clients that support QAM-256. Short guard interval (802.11n) On/off switchable; increase of throughput by reducing the guard intervals from 800ns to 400ns. Output power limitation Adjustable. Output Power @ 2.4 GHz Max. 16,35 dBm. Bandwidth (802.11n) 20 MHz / (40MHz with coexistence check under preparation). Antenna Integrated directional dual-band MIMO array with 3.65 dB peak gain @ 2.4 GHz. Technical Information Teldat S.A. 26 Teldat Connect-KFPlus

WLAN standards IEEE 802.11ac/an; MU-MIMO 2x2; 20/40/80 MHz; 5 GHz Frequency bands 5 GHz indoor (EU) 5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed Frequency bands 5 GHz out- door (EU) 5 GHz outdoor (5470-5725 MHz) max. 1000 mW EiRP allowed WLAN modes 5 GHz Operation: 802.11a only; 802.11a/n; 802.11n. Modulation Techniques OFDM: BPSK, QPSK, DBPSK, DQPSK,16-QAM, 64-QAM, 256-QAM. Automatic Rate Selection (ARS) Available. Transmission rate Automatic. Data rates 802.11a,h (5 GHz): 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation). 802.11n, 20 MHz channel bandwidth: MCS0-15 allow up to 150 Mbps PHY rate at 20 MHz channel bandwidth, 2 streams, short guard interval. 802.11n, 40 MHz channel bandwidth: MCS0-15 allow up to 300 Mbps PHY rate at 40 MHz channel bandwidth, 2 streams, short guard interval. 802.11ac, 20 MHz channel bandwidth: Allow up to 173 Mbps PHY rate with two streams or up to 87 Mbps PHY with one stream. 802.11ac, 40 MHz channel bandwidth: Allow up to 400 Mbps PHY rate with two streams or up to 200 Mbps PHY with one stream. 802.11ac, 80 MHz channel bandwidth: Allow up to 867 Mbps PHY rate with two streams or up to 433 Mbps PHY with one stream. Short guard interval (802.11n) On/off switchable; increase of throughput by reducing the guard intervals from 800ns to 400ns. Output power limitation Adjustable. Output power @ 5 GHz Max. 18,12 dBm (200mW EiRP). Bandwidth (802.11ac) 20/40/80 MHz. Antenna Integrated directional dual-band MIMO array with 4.88 dB peak gain @ 5 GHz. A.5.9 Configuration Interface LOCAL TERMINAL RS-232 9600-8-N-1 without flow control. CONNECTOR RJ45 female on the rear panel. A.5.10 Power Supply INPUT VOLTAGE +12V DC. INPUT CURRENT 2.1 A. CONNECTOR Jack 5.5/2.5 mm. Teldat S.A. Technical Information Teldat Connect-KFPlus 27

TYPE Desktop / chassis for a 1 U high Rack mount enclosure. L x W x H 310 x 197 x 45 mm. WEIGHT 2.04 Kg. A.5.12 Environmental Specifications TEMPERATURE OPERATING NORMALLY: 0 ºC to 45 ºC. STORED: -25 ºC to 70 ºC. RELATIVE HUMIDITY 5 % to 90 %. Technical Information Teldat S.A. 28 Teldat Connect-KFPlus

This section includes some of the European radio frequencies that comply with the CE regulatory requirements. Cus- tomers may obtain additional country-specific bands upon request. B.1 WI-FI specifications This product is supplied with internal antennas. Technology: WLAN 802.11a/b/g/n/ac. Frequency Range 802.11b/g/n-HT20: 2412 ~ 2472MHz; 802.11n-HT40: 2422 ~ 2462MHz; 802.11a /n-HT20/ac-VHT20: 5180~5240 MHz, 5260~5320 MHz, 5500~5700 MHz; 802.11n-HT40/ac-VHT40: 5190~5230 MHz, 5270~5310 MHz, 5510~5670 MHz; 802.11ac-VHT80: 5210 MHz, 5290 MHz, 5530 MHz, 5610 MHz. Number of Channels 802.11a/n-HT20/ac-VHT20: 19 802.11n-HT40/ac-VHT40: 9 802.11ac-VHT80: 4 Type of modulation 2.4 GHz: 802.11b: DSSS 802.11g/n: OFDM. 5.0 GHz: 802.11a/n/ac: OFDM. Teldat S.A. CE Radio Information Teldat Connect-KFPlus 29