Teeter FS-1 1324276 Assembly Instructions Manual

Assembly Instructions YEAR 5 W A R R A N T Y FULL NEW! Follow along with your smartphone to make assembly even easier! For gravity-assisted stretching and decompression To download and print the Teeter FS-1™ instructions in French, visit the Product Manuals page at teeter.com. * Specifications may vary from this image and are subject to change without notice. EN founder & innovator I created Teeter so people could live healthier, more active lives. ITM. / ART. 1324276 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 1 User Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Prepare to Invert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 – 4 Inverting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – 5 Storage & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Get the Most out of Your Teeter . . . . . . . . . . . . . . . . . . . . . . 6 Assembly Instructions Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 1 Parts for Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Understanding Your Inversion Table . . . . . . . . . . . . . . . . . . 3 Safety Warning Labels & Product Specifications . . . . . 4 Before Beginning Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 – 11 Misassembly Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Before Inverting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warranty Terms & Registration . . . . . . . . . . . . . . . . . . . . . . 15 Congratulations on your purchase of a Teeter FS-1™ Inversion Table! For the best experience, it is critical that you follow the assembly instructions, read and fully understand the Owner’s Manual attached to the equipment, and review the Getting Started Video Portal prior to using your new Teeter Inversion Table. Teeter Decompression Devices are 510(k) registered with the FDA and are multiple user, reusable medical devices for home use, intended to provide traction to the spine while stretching the para-spinal muscle and soft tissues. The devices provide non-powered traction and are meant for use by adults. Teeter Decompression Devices are indicated for the following conditions: back pain, muscle tension, degenerative disc disease, spinal degenerative joint disease, spinal stenosis, herniated disc, spinal curvature due to tight muscles, sciatica, muscle spasm, and facet syndrome. For step-by-step, 3D interactive instructions, download BILT (a FREE mobile app) to your smartphone to follow along. See Page 5 for instructions on how to download BILT. To register your product warranty, go to teeter.com/Support/Warranty-Registration If you have any questions concerning assembly or if any parts are missing, DO NOT RETURN THE ITEM TO THE STORE OR CONTACT THE RETAILER. Our dedicated product service experts can help! Contact Teeter Customer Service at 800.847.0143, or via online forms or Live Chat at teeter.com. Get more from your inversion sessions with TeeterLink®, the FREE app that lets you track usage and pain levels, get reminders and customized guidance, access support, and more! Scan the code or search TeeterLink® in your app store to get started! TeeterLink® Get

WARNING ! IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity. FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. To reduce the risk of injury: • Read and understand all the instructions, review all other accompanying documents, and inspect the equipment before using the inversion table. It is your responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion if these instructions are not followed, such as falling on your head or neck, pinching, entrapment, equipment failure, or aggravating a pre-existing medical condition. It is the responsibility of the owner to ensure that all users of the product are fully informed about the proper use of the equipment and all safety precautions. • DO NOT use until approved by a licensed physician. Inversion is contraindicated in any medical or health condition that may be made more severe by an elevation of blood pressure, intracranial pressure or mechanical stress of the inverted position, or that may impact your ability to operate the equipment. This may include injury or illness, but also the side effects of any drug or supplement (prescribed or over-the-counter). Specific conditions may include, but not be limited to: · Any condition, neurological or otherwise, which results in unexplained tingling, weakness or neuropathy, seizure, sleep disorder, lightheadedness, dizziness, disorientation, or fatigue, or impacts strength, mobility, alertness, or cognitive ability; · Any brain condition, such as trauma, history of intracranial bleed, history or risk of TIA or stroke, or severe headaches; · Any condition of the heart or circulatory system, such as high blood pressure, hypertension, increased risk of stroke, or use of anticoagulants (including high doses of aspirin); · Any bone, skeletal or spinal cord condition or injury, such as significant spinal curvature, acutely swollen joints, osteoporosis, fractures, dislocations, medullary pins or surgically implanted orthopedic supports; · Any eye, ear, nasal or balance condition, such as trauma, history of retinal detachment, glaucoma, optic hypertension, chronic sinusitis, middle or inner ear disease, motion sickness, or vertigo; · Any digestive or internal condition, such as severe acid reflux, hiatal or other hernia, gallbladder or kidney disease; · Any condition for which exercise is specifically directed, limited or prohibited by a physician, such as pregnancy, obesity, or recent surgery. • ALWAYS be certain the Ankle Lock System is properly adjusted and fully engaged, and that your ankles are secure before using the equipment. HEAR, FEEL, SEE and TEST that the Ankle Lock System is snug, close-fitting and secure EVERY TIME you use the equipment. • ALWAYS wear securely tied lace-up shoes with a flat sole, such as a normal tennis-style shoe. • DO NOT wear any footwear that could interfere with securing the Ankle Lock System, such as shoes with thick soles, boots, high-tops or any shoe that extends above the anklebone. • DO NOT use the inversion table until it is adjusted properly for your height and body weight. Improper settings can cause rapid inversion or make returning upright difficult. New users, and users who are physically or mentally compromised, will require the assistance of a spotter. Make sure the equipment is set to your unique user settings prior to each use. • DO NOT sit up or raise head to return upright. Instead, bend knees and slide your body to the foot-end of the inversion table to change weight distribution. If locked out in full inversion, follow the instructions for releasing from the locked position before returning upright. • DO NOT continue using the equipment if you feel pain or become light-headed or dizzy while inverting. Immediately return to the upright position for recovery and eventual dismount. • DO NOT use if you are over 198 cm / 6 ft 6 in / 6 po 6 pi or over 136 kg (300 lb). Structural failure could occur or head / neck may impact the floor during inversion. • DO NOT allow children to use this machine. Keep children, bystanders, and pets away from machine while in use. The inversion table is not intended for use by persons with reduced physical, sensory or mental capabilities, unless they are given supervision and instruction concerning use of the machine by a person responsible for their safety. • DO NOT store the inversion table upright if children are present. Fold and lay the table on the floor. DO NOT store outdoors. • DO NOT use aggressive movements, or use weights, elastic bands, any other exercise or stretching device or non-Teeter® attachments while on the inversion table. Use the inversion table only for its intended use as described in this manual. • DO NOT drop or insert any object into any opening. Keep body parts, hair, loose clothing and jewelry clear of all moving parts. • DO NOT use in any commercial, rental or institutional setting. This product is intended for indoor, home-use only. • DO NOT operate equipment while under the influence of drugs, alcohol, or medication that may cause drowsiness or disorientation. • ALWAYS inspect the equipment prior to use. Make sure all fasteners are secure. • ALWAYS replace defective components immediately and / or keep the equipment out of use until repair. • ALWAYS position equipment on a level surface and away from water or ledges that could lead to accidental immersion or falls. • Refer to additional warning notices posted on the equipment. If a product label or Owner’s Manual should become lost, damaged or illegible, contact Customer Service for replacement. 1

Parts are not shown to scale. Hardware drawings located on the insert inside each Hardware Kit. Stretch-and-Grip™ A-Frame Base Assembly with pre-assembled Angle Tether E61100 F51007 FitSpine™ Table Bed Assembly Use with Table Bed Hardware Kit (HK1010) EX1300 E61500 F51064B EX1800 ITEM NO. ITEM NAME Stretch-and-Grip™ A-Frame Base Assembly E61100 A-Frame F51007 Angle Tether pre-assembled to A-Frame Handle Assembly E61500 Stretch Assist™ Handles (2) HK1008 Handle Assembly Hardware Kit F50071 Allen Head Bolt (6) Roller Hinge Assembly F51064B Roller Hinges (2) FitSpine™ Table Bed Assembly EX1300 FitSpine™ Table Bed HK1010 FitSpine™ Table Bed Hardware Kit EP1127 Bolt (2), H13009 Nut (2), EP1128 Washer (2) Handle Assembly Use with Handle Assembly Hardware Kit (HK1008) Roller Hinge Assembly Optional Head Pillow Tools Provided for Assembly IA1149 5mm Allen Wrench EZ-Reach™ Ankle Lock System EX1630 F51088 Open-Ended Wrench ITEM NO. ITEM NAME Main Shaft Assembly EX1630 with EZ-Reach™ Ankle Lock System Optional Accessories EX1800 Head Pillow Tools Provided for Assembly IA1149 5mm Allen Wrench (1) EP1128A 6mm Allen Wrench (1) F51088 Open-Ended Wrench (1) Product Support LI3900 Owner’s Manual pre-assembled to A-Frame Product Support LI3900 Owner’s Manual REV. DESCRIPTION REV.DATE APP.DATE APPROVED STL-20150420-說明書 2015/4/20 C A B D E 6 5 4 3 2 9 8 7 C A B D E F G H 1 2 3 4 5 6 7 8 9 F G H 2 EP1128A 6mm Allen Wrench Main Shaft Assembly

bed. Identifying Parts and Components Understanding Your Inversion Table Before reading further, study the drawing below to familiarize yourself with the important components of your Teeter Inversion Table. 1 Head Pillow 2 Upper Support Arms 3 FitSpine™ Table Bed 4 Pivot Pins 5 Hinge Plates 6 Self-Locking Hooks 7 3-Hole Roller Hinges 8 Handles 9 Height-Selector Locking Pin 10 Spreader Arms 11 Angle Tether 12 Crossbar 1 9 10 8 13 11 15 16 17 4 5 6 7 14 12 13 A-Frame 14 Main Shaft 15 Ankle Lock System 16 Ankle Comfort Dial™ 17 Non-Skid Stability Feet 3 3 2

Important: Please review all labels and supporting materials before using your inversion table. This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or is removed, contact Teeter Customer Service to request a complimentary replacement label. Note: Image and labels below not shown at actual size. Assembled Non-Use Dimensions: 147.3 x 73.1 x 153.6 cm / 58 x 28.8 x 60.5 in Maximum In-Use Dimensions: 205.7 x 73.1 x 219.7 cm / 81 x 28.8 x 86.5 in Storage Dimensions: 50.8 x 73.1 x 167.6 cm / 20 x 28.8 x 66 in Weight (approx.): 28.4 kg / 62.6 lb 73.1 cm / 28.8 in 153.6 cm / 60.5 in 147.3 cm / 58 in 4 SERIOUS INJURY OR DEATH MAY OCCUR IF PRECAUTION IS NOT TAKEN. To reduce this risk: • READ and understand instructions in Owner’s Manual and on equipment before attempting to use. • ALWAYS properly set Main Shaft height. Too short can cause rapid inversion and difficultly returning upright. • TIPPING HAZARD: Ensure that Spreader Arms are fully engaged in the locked position. To store upright, leave A-Frame open enough to remain stable or secure to wall. If children are present, store flat on floor, not upright. • DO NOT allow children to use this machine. Keep children, bystanders and pets away when in use. • Keep body parts, hair, loose clothing and jewelry clear of all moving parts. • Height / Weight Capacity: 142 - 198 cm / 4 ft 8 in - 6 ft 6 in; 136 kg / 300 lb. For consumer, indoor Home-Use Only.

For step-by-step, 3D interactive instructions, download BILT (a FREE mobile app) to your smartphone to follow along. Simply download the BILT app by scanning the QR code below and then search for Teeter FS-1 within the BILT app to get started! Making Assembly Even Easier with 5 Unpack and Prepare Your Workspace • If possible, assemble the equipment at or near the space in which you intend to use it to avoid moving it later. • Unpack all parts and support materials. Set aside packing materials and clear your work area. • Locate the Hardware Kits packaged with the manuals. They are labeled to correspond with the assembly process. • The Getting Started Video Portal at teeter.com/videos provides step-by-step instruction on how to assemble your product. You may find it helpful to follow along with the videos by watching them on either your phone, tablet, or computer. The videos include important use instructions such as: • Assembly - Follow step-by-step instruction on how to assemble your Teeter • User Settings - Personalize your inversion experience by adjusting four customizable settings. • How to Invert - Learn how to test your balance and rotation control, and how to properly invert and return upright. • Dismounting - Learn how to properly dismount your Teeter according to your specific model. • Storage & Maintenance - When not in use, store your Teeter easily and compactly. • Accessories - Learn more about the accessories available for your Teeter. • Healthy Back and Body Routines* Get guided instruction on stretches and exercises you can do on your own to help strengthen your back and gain flexibility. Access this exclusive bonus content at teeter.com/videos with the password: healthyback. *Not available in French or Spanish.

• On a level surface, position the A-Frame so that it is standing upright and the Stability Feet are on the ground. • Gently push down on the Spreader Arms to ensure they are fully open and in the “locked” position (Figure 1). • Look for temporary circular assembly assistance labels on the A-Frame. RIGHT, LEFT, FRONT, and REAR indicate your position while using the equipment, not facing it. These labels can be removed easily upon completion of assembly. • Locate the Handle Assembly Hardware Kit (HK1008). • Determine the left or right handles, marked with an embossed L / R on the inside of the black plastic part of each handle. • Align the black plastic part of the corresponding handle (left / right) over the outside edge of the Hinge Plate on the A-Frame (Figure 2). • Insert and loosely hand-tighten three of the Allen Head Screws through the Hinge Plate into the handle (Figure 3). • Repeat with other handle. Tighten all fasteners with the 5mm Allen Wrench provided, being careful not to over-tighten. 1 - Spreader Arms 2 - Crossbar LEFT RIGHT FIGURE 1 1 2 REAR FRONT FIGURE 2 FIGURE 3 FIGURE 1a UNLOCKED 6

• Locate the Table Bed Assembly Hardware Kit (HK1010). • Place the Table Bed face down on the floor and push down on the Support Beam, so the two holes align evenly with the holes at the base of the Upper Support Arms (Figure 4). You may have to exert extra pressure to ensure that the Support Beam slides over the rubber spacers. • Insert the two Bolts into the open holes (Figure 5). • Thread a Washer and Nut onto each Bolt and hand-tighten. • Using the 6mm Allen Wrench to steady the bolts, tighten the Nuts onto the Bolts with the 10/13mm Open-Ended Wrench. FIGURE 4 FIGURE 5 1 2 1 Support Beam 2 Upper Support Arms

UNLOCK LOCK LOCKED NEVER disassemble the Roller Hinge Pivot Pin. ALWAYS insert the 3-Hole Roller Hinge (with the Pivot Pin on top and facing out) in the same direction as the arrow label located inside of the Cam Lock for proper assembly. WARNING ! • For ease of assembly, rest the Table Bed against the Crossbar (Figure 7) at the front of the A-Frame. • On one side of the Table Bed, lift and hold the Cam Lock up all the way to unlock (Figure 8). • In your other hand, hold one Roller Hinge near the Pivot Pin. With the Pivot Pin facing out (away from the Table Bed), slide the bottom of the Roller Hinge between the Cam Lock and the Bracket in the same direction as the arrow label located inside of the Cam Lock. TIP: Make sure that the Cam Lock is completely open when inserting the Roller Hinge, otherwise assembly will be more difficult. • Engage one of the holes in the Roller Hinge over the Bracket Pin. Figure 10 shows the Roller Hinge installed correctly, with the Bracket Pin engaged in Setting C. NOTE: Refer to the Owner’s Manual for an explanation of the hole settings. If you are unsure, use Setting C to start. • Push down on the Cam Lock (Figure 9) to lock it and secure the Roller Hinge. • Repeat on other side. Make sure the Roller Hinges are in the same hole setting on both sides. FIGURE 6 FIGURE 8 FIGURE 7 FIGURE 9 FIGURE 10 • Familiarize yourself with the 3-Hole Roller Hinge and Cam Lock terms (Figure 6).

• Grasp both Roller Hinges, right above the Cam Lock, and lift the Table Bed. Allow the top of the Table Bed to rotate toward the floor, so that the back of the Table Bed is now facing you and the top of the Table Bed is in front of the Crossbar (Figure 12). • Lower each Roller Hinge Pivot Pin into the A-Frame hinge plates, one side at a time (Figure 13). The Self-Locking Hooks will open to allow the Pivot Pin into the Hinge Plate slot, then automatically snap closed over the Pivot Pin. TIP: You may need to push outward on the Hinge Plate in order for the second Pivot Pin to lock in place. • Make sure that each Pivot Pin is seated at the base of the slot in the Hinge Plates, and that the Self-Locking Hooks have closed over both Pivot Pins (Figures 13a & 13b). Failure of the Self-Locking Hooks to close over both Roller Hinge Pivot Pins is an indication of improper assembly and if not corrected could result in serious injury or death! WARNING ! STEP 4 Assemble Table Bed to A-Frame • Rotate the Table Bed into the use position (Figure 14). Ensure that it rotates smoothly. See also Image A on Page 12 to ensure correct assembly. TOP VIEW INSIDE VIEW FRONT REAR FIGURE 13 FIGURE 14 FIGURE 13b FIGURE 13a FIGURE 11 FIGURE 12

hand with the height markings facing up. Slide the end of the Main Shaft into the Main Shaft Housing (Figure 15), located at the base of the Table Bed. • With your right hand, pull out the Height-Selector Locking Pin (Figure 16) to allow the Main Shaft to slide in further and release in the desired height setting. Refer to the Owner’s Manual for more information on selecting your height setting. • The Main Shaft MUST REST against the Crossbar bumper on the A-Frame (Figure 17). IMPORTANT: The Crossbar prevents the Table Bed from rotating forward when the user steps on the Ankle Comfort Dial. If the Main Shaft does not rest on the Crossbar bumper as shown in Figure 16, then the Table Bed has been assembled backwards onto the A-Frame. This MUST BE CORRECTED before use. See also Image B on Page 12 to ensure correct assembly. • Test the inversion table by hand for smooth and steady rotation (Figure 18) and ensure that all fasteners are secure. STEP 5 Assemble Main Shaft to Table Bed FIGURE 15 FIGURE 16 FIGURE 17 FIGURE 18

Attach Angle Tether • The tether will come pre-assembled to the A-Frame. • Unfold the adjustable tether and clip it to the U-Bar on the underside of the Table Bed (Figure 19). • Slide the buckle to lengthen or shorten the strap depending on your desired maximum angle of inversion. Attach Head Pillow Attach the Head Pillow by securing the hook and loop straps through the specified holes in the Table Bed (Figure 20), which allow the pillow to shift with the user when in use. You may also customize the position depending on your preference. LENGTHEN SHORTEN FIGURE 19 FIGURE 20

Demonstrates that the Table Bed has been assembled into the A-Frame backwards so the Main Shaft is not resting on the Crossbar and must be corrected. Image A Go back to Step 3 for instruction. Demonstrates that the Roller Hinges have been assembled upside down into the Table Bed and must be corrected. Misassembly Check If your Teeter Inversion Table looks like either of these images, your inversion table has been misassembled and is unfit for use. Improper assembly could result in serious injury or death! WARNING ! REVISIONS ENGR DATE REV SHT ZONE DESCRIPTION NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT PARTS LIST ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT REVISION STATUS SHT 1 REV A 8 A 1 2 3 4 5 6 7 D C B C A D B 5 3 1 6 2 4 8 7 8 A 1 2 3 4 5 6 7 D C B C A D B 5 3 1 6 2 4 8 7 bed on backwards missassembly SHEET 1 OF 1 REV PROJECT: DRAWN UNLESS OTHERWISE NOTED SURFACE ROUGHNESS PER ANSI B46.1 DIMENSIONING PER ASME Y14.5-2009 WELD SYMBOLS PER AWS A2.4 FINISH: UOS 63RMS ON MACHINED SURFACES OR AS PROCURED .X .XX .XXX ANGLE EXPECTATIONS PROPRIETARY THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO EXPECTATIONS AND SHALL NOT BE REPRODUCED IN WHOLE OR IN PART OR USED FOR ANY PURPOSE EXCEPT WHEN SUCH USER POSSESSES DIRECT WRITTEN AUTHORIZATION FROM EXPECTATIONS LLC SCALE: FULL SIZE: D A TOLERANCES UNLESS NOTED = .1 = .03 = .005 = 1 NICK SOLLER FILLET RADII: .005-.010 CORNER BREAK: .005-.010 ALL DIMENSIONS IN INCHES EXPECTATIONS LLC PUYALLUP, WA 98391 DRAWING PROJECT NAME HERE REVISIONS ENGR DATE REV SHT ZONE DESCRIPTION NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT PARTS LIST ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT REVISION STATUS SHT 1 REV A 8 A 1 2 3 4 5 6 7 D C B C A D B 5 3 1 6 2 4 8 7 8 A 1 2 3 4 5 6 7 D C B C A D B 5 3 1 6 2 4 8 7 roller hinges missassembled SHEET 1 OF 1 REV PROJECT: DRAWN UNLESS OTHERWISE NOTED SURFACE ROUGHNESS PER ANSI B46.1 DIMENSIONING PER ASME Y14.5-2009 WELD SYMBOLS PER AWS A2.4 FINISH: UOS 63RMS ON MACHINED SURFACES OR AS PROCURED .X .XX .XXX ANGLE EXPECTATIONS PROPRIETARY THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO EXPECTATIONS AND SHALL NOT BE REPRODUCED IN WHOLE OR IN PART OR USED FOR ANY PURPOSE EXCEPT WHEN SUCH USER POSSESSES DIRECT WRITTEN AUTHORIZATION FROM EXPECTATIONS LLC SCALE: FULL SIZE: D A TOLERANCES UNLESS NOTED = .1 = .03 = .005 = 1 NICK SOLLER FILLET RADII: .005-.010 CORNER BREAK: .005-.010 ALL DIMENSIONS IN INCHES EXPECTATIONS LLC PUYALLUP, WA 98391 DRAWING PROJECT NAME HERE

The Owner’s Manual contains important information on how to use your Teeter Inversion Table, including how to personalize the user settings, properly secure and release the Ankle Lock System, and test and adjust the rotation control. • If not already attached, thread the provided metal chain through the pre-punched hole in the upper corner of the Owner’s Manual. • Secure the chain to the A-Frame through the designated hole in the Hinge Plate (Figure 21 & 21a). Allow the Owner’s Manual to hang freely on the outside of the A-Frame Spreader Arms so it doesn’t interfere with the rotation of the Table Bed. IMPORTANT: Once attached to the A-Frame, DO NOT remove the Owner’s Manual. It should remain permanently attached to your inversion table to serve as a reference for all users in regards to proper adjustment and use of the equipment. WARNING ! Watch the Getting Started Videos The Getting Started Video Portal is a helpful supplement to the Owner’s Manual, with easy-to-follow instructions on user settings, how to invert, storage and maintenance, and even stretching and exercises you can do with your Teeter. Just go to teeter.com/videos to access them now! Read the Owner’s Manual thoroughly before using your Teeter Inversion Table. Improper settings could result in serious injury or death! FIGURE 21a FIGURE 21 Download TeeterLink® Get more from your inversion sessions by downloading the TeeterLink® app to your phone to track usage and pain levels, get reminders and customized guidance, access support, and more! Scan the code or search TeeterLink® in your app store to get started!

Step 1 Fill out this information for your own records. Step 2 Go online to teeter.com to register your warranty. Handling and transportation costs related to product warranty service only are covered by this warranty. This warranty does not cover damage resulting from improper handling, assembly, or installation, repairs made by others, accident, misuse, or abuse. Under no circumstances shall Teeter, or any other party involved in the sale of this product, have any liability for incidental or consequential damage arising from breach of an express or implied warranty on any Teeter product. EXCEPT AS SET FORTH ABOVE, NO WARRANTY IS GIVEN WITH RESPECT TO ANY TEETER PRODUCT, AND ALL EXPRESS WARRANTIES ARE DISCLAIMED. This warranty shall be governed by the laws of the State of Washington, USA. To the extent this warranty is found not to be enforceable, it shall be deemed revised to the extent necessary to make it enforceable. Any controversy or claim arising out of or relating to this warranty, its interpretation, or any alleged breach thereof, which cannot be amicably settled between Teeter and the owner within sixty (60) days of written notice by the aggrieved party to the other, shall be finally settled by arbitration submitted to three (3) arbitrators selected from the panels of the arbitrators of the American Arbitration Association located closest to Teeter’s principal place of business. Some states do not allow the exclusion of incidental or consequential damage from a warranty, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from state / province to state / province. This warranty is completely transferable to any and all future owners of this product, provided no alterations have been made to the product. AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. PLEASE RETAIN THIS FOR YOUR RECORDS Date of Purchase Product & Model Dealer Name Serial No. located on the back of the Table Bed YEAR 5 W A R R A N T Y FULL During the period starting with the day of retail purchase and continuing for five (5) years, Teeter extends to the owner a repair and replacement warranty against manufacturing defects in materials, workmanship, fabrics and padding. Teeter will repair or replace any such defect and will pay the costs of all parts, labor and transportation. If a repair or replacement is not commercially practical or cannot timely be made, then Teeter will, at the original Purchaser’s option, replace with a comparable product or refund the purchase price. FULL 5 YEAR WARRANTY If you are unable to go online, you can request a warranty card to be mailed to you by calling Customer Service at 800-847-0143. Please DO NOT mail this to Teeter. 15 The Teeter warranty set forth below and on Teeter.com applies to the Inversion Table only. Accessories may come with their own terms. This warranty applies to US and Canadian customers only. For international customers, please consult your local distributor for warranty information which will vary depending on country.

© COPYRIGHT 2019 Teeter. International Law Prohibits Any Copying. LI3901 1019-1 Teeter Decompression Devices are multiple user, reusable devices for home use, intended to provide traction to the spine while stretching the para-spinal muscles and soft tissues. The devices provide non-powered traction and are meant for use by adults. Use of the Teeter Decompression Devices is indicated for the following conditions: back pain, muscle tension, degenerative disc disease, spinal degenerative joint disease, spinal stenosis, herniated disc, spinal curvature due to tight muscles, sciatica, muscle spasm, and facet syndrome. Medical Device Safety Service GmbH Schiffgraben 41 30175 Hannover Germany Tel. +49 511 62628630 EC REP Any modification to this device will void the UL Listing. This product is Listed by Underwriters Laboratories Inc. Representative samples of this product have been evaluated by UL and meet applicable safety standards. This product is Listed by Underwriters Laboratories Inc. Representative samples of this product have been evaluated by UL and meet applicable safety standards. This product is Listed by Underwriters Laboratories Inc. Representative samples of this product have been evaluated by UL and meet applicable safety standards. This product is Listed by Underwriters Laboratories Inc. Representative samples of this product have been evaluated by UL and meet applicable safety standards. If you have any trouble assembling the equipment, or questions about its use, please contact customer service. International: Teeter International, Ltd. Gor-Ray House 758 Great Cambridge Rd Enfield Middlesex EN1 3GN United Kingdom teeterintl.com | [email protected] USA: 800-847-0143 or [email protected] (English language) International: [email protected] Hours of Operation (Monday - Friday 8am - 4pm PST) USA: Teeter 9713 233rd Avenue East Bonney Lake, WA 98391 Toll Free: 800-847-0143 Fax: 800-847-0188 teeter.com | [email protected] Distributed by: Costco Wholesale Corporation P.O. Box 34535 Seattle, WA 98124-1535 USA 1-800-774-2678 www.costco.com Costco Wholesale Canada Ltd.* 415 W. Hunt Club Road Ottawa, Ontario K2E 1C5, Canada 1-800-463-3783 www.costco.ca * faisant affaire au Québec sous le nom les Entrepôts Costco Importado por: Importadora Primex S.A. de C.V. Blvd. Magnocentro No. 4 San Fernando La Herradura Huixquilucan, Estado de México C.P. 52765 RFC: IPR-930907-S70 (55)-5246-5500 www.costco.com.mx Costco Wholesale Australia Pty Ltd 17-21 Parramatta Road Lidcombe NSW 2141 Australia www.costco.com.au Costco Wholesale UK Ltd / Costco Online UK Ltd Hartspring Lane Watford, Herts WD25 8JS United Kingdom 01923 213113 www.costco.co.uk Costco Wholesale Spain S.L.U. Polígono Empresarial Los Gavilanes C/ Agustín de Betancourt, 17 28906 Getafe (Madrid) España NIF: B86509460 900 111 155 www.costco.es Costco Wholesale Iceland ehf. Kauptún 3-7, 210 Gardabaer Iceland www.costco.is Costco France 1 avenue de Bréhat 91140 Villebon-sur-Yvette France 01 80 45 01 10 www.costco.fr Costco Wholesale Japan Ltd. 3-1-4 Ikegami-Shincho Kawasaki-ku, Kawasaki-shi, Kanagawa 210-0832 Japan 0570-032600 www.costco.co.jp Costco Wholesale Korea, Ltd. 40, Iljik-ro Gwangmyeong-si Gyeonggi-do, 14347, Korea 1899-9900 www.costco.co.kr Costco President Taiwan, Inc. No. 656 Chung-Hwa 5th Road Kaohsiung, Taiwan Company Tax ID: 96972798 449-9909 or 02-449-9909 (if cellphone) www.costco.com.tw Shanghai Minhang Costco Trading Co., Ltd Unit 109, No 388, Lian You Road Minhang District, Shanghai China 201107 +86-21-6257-7065