Commell LV-673 Serial Operation & User’s Manual

Product Specification 7 Chapter 1 1.1 LV-673(E) is the new generation of the Mini-ITX motherboard, with supporting last Intel Pentium M processors for 533MHz front side bus, Intel 915GM(E) and ICH6-M chipset, integrated GMA900 graphics, DDR2 memory, REALTEK High Definition Audio, Serial ATA, PCI Express 16x interface and dual Gigabit LAN. New Intel Pentium M Processor The board supports last Intel Pentium M processors with 533MHz front side bus, 2MB L2 cache, to provide more powerful performance than before. New features for Intel 915GM(E) chipset The board integrates Intel 915GM(E) and ICH6-M chipset, to provide new generation of the mobile solution, supports Intel GMA900 graphics, DDR2 400/533 memory, built-in high speed mass storage interface of serial ATA, High Definition Audio with 7.1 channels surrounding sound. All in One multimedia solution Based on Intel 915GM(E) and ICH6-M chipset, the board provides high performance onboard graphics, 18-bit dual channel LVDS interface, HDTV and 7.1 channels High Definition Audio, to meet the very requirement of the multimedia application. LV-673(E) not supports TV out function. Flexible Extension Interface The board provides one PCI-Express 16x slots for graphics card, it also can support PCI-Express 1x for LAN card or other devices. The board also provides one PCMCIA Type II slot, CompactFlash Type I slot and one mini-PCI slot.

8 1.2 General Specification Form Factor Mini-ITX motherboard CPU Intel® Pentium M / Celeron M processors Package type: FC-PGA478 L2 Cache: 512KB/1MB/2MB Front side bus: 400/533MHz ( The Intel® Celeron® M Processor 4xx series can not be used on LV-673(E) series .) Memory 2 x 240-pin DDR2 400/533MHz SDRAM up to 2GB Up to 8GB/s of bandwidth with dual-channel interleaved mode Dual-Channel technology supported Unbufferred, none-ECC memory supported only Chipset Intel® 915GM(E) (Northbridge) and ICH6-M (Southbridge) BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS Green Function Power saving mode includes doze, standby and suspend modes. ACPI version 1.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min. of timeout value Real Time Clock Intel® ICH6-M built-in RTC with lithium battery Enhanced IDE UltraDMA33 IDE interface supports up to 2 ATAPI devices One 44-pin IDE port onboard One CompactFlash Type I socket on solder side Serial ATA Intel® ICH6-M integrates 2 Serial ATA interfaces Up to 150MB/s of transfer rate Multi-I/O Port Chipset Intel® ICH6-M with Winbond® W83627THF controller Serial Port Two external and two internal RS-232 serial ports USB Port Six Hi-Speed USB 2.0 ports with 480Mbps of transfer rate Parallel Port None Floppy Port One slim type Floppy port IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O interface Smart Fan One CPU fan connectors for fan speed controllable VGA Display Interface Chipset Intel® 915GM(E) GMCH (Graphic Memory Controller Hub) Frame Buffer Up to 128MB shared with system memory Display Type CRT, LCD monitor with analog display Onboard 18-bit dual channel LVDS interface Onboard HDTV interface Connector External DB15 female connector on rear I/O panel

Product Specification 9 Onboard 40-in LVDS connector Onboard 8-pin TV-out connector Ethernet Interface Controller Marvell E8053 PCI Express Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector Dual External RJ45 connectors with LED on rear I/O panel Audio Interface Chipset Intel® ICH6M with Realtek® ALC880 codec Intel High Definition Audio compliance Interface 7.1 channels sound output Connector External Audio phone jack for Line-out, Line-in, MIC-in, Surround, Center and Backsurround Onboard audio connector with pin header (built-in amplifier for speaker out) Onboard CD-IN connector Expansive Interface PCI-Express One 16x PCI-Express slot (compatible with 1x slot) Up to 8GB/s of transfer bandwidth Power supply: +3.3V, +12V PCI One Mini-PCI socket for TYPE III (32-bit, 33MHz) Power supply: +3.3V, +5V PCMCIA One PCMCIA Type II slot on solder side with RICOH R5C475II controller Power and Environment Power Requirement DC 12V input with external DC mini DIN or onboard 4-pin connector Input Range 10.5V ~ 13V Dimension 170 (L) x 170 (H) mm Temperature Operating within 0 ~ 60P oPC (32 ~ 140P oPF) Storage within -20 ~ 85P oPC (-4 ~ 185P oPF) Ordering Code LV-673(E) Intel Pentium M platform with onboard VGA, HD audio, SATA USB2.0, LVDS, HDTV, PCI-Express, Mini-PCI, CF, PCMCIA 4 x COM LV-673(E) not supports TV out function. PCIE-SDVOD PCI-Express add-on card for single DVI interface The specifications may be different as the actual production. For further product information please visit the website at TUhttp://www.commell.com.twUT

Block Diagram 11 1.4 Intel Pentium M/Celeron M Processors Intel GMA900 Graphics PCI-Express x16 LVDS 2 x 240-pin DDR2 400/533MHz up to 2GB 915GM(E) ICH6-M 2 x Serial ATA ports PCI Express 1x 6 x USB2.0 ports Marvell E8053 Gigabit LAN PCI Mini-PCI slot UltraDMA33 IDE CompactFlash PCMCIA BIOS HD Audio 4 x Serial ports 1 x Floppy ports 8-bit GPIO IrDA

Connector Location 13 Chapter 2 2.1 CN_AUDIO SPDIF CDIN CN_IR MINIPCI CN_USB PWRIN PEG SATA1 SATA2 CN_LVDS CN_DIO CN_COM34 CPUFAN CN_TV CPU SYSFAN CN_INV CN_BPWR DDRIIB/A JFRNT IDE FDD Solder side: CF CARDBUS DC_IN COM1/2 USB_RJ45_A/B KB MS AUDIO VGA

Jumper Location & Reference 14 2.2 Jumper Function JRTC CMOS Operating/Clear Setting JCFSEL CF with IDE mode selection JVLCD Panel Voltage Setting JCFSEL JVLCD JRTC

Connector Location 15 2.3 2.3.1 Connector Function Remark CPU Socket479 for CPU Standard DDRIIA/B 240 -pin DDR2 SDRAM DIMM socket Standard IDE 44-pin IDE connector Standard FDD 26-pin slim type floppy connector Standard S_ATA1/2 7-pin Serial ATA connector Standard PWRIN 4-pin power input connector Standard CN_BPWR 4-pin power output connector Standard CN_AUDIO 5 x 2-pin audio connector Standard SPDIF 4-pin S/PDIF digital audio output connector Standard CDIN 4-pin CD-ROM audio input connector Standard CN_DIO 6 x 2-pin digital I/O connector Standard CN_USB 5 x 2-pin USB connector Standard CPUFAN 4-pin CPU cooler fan connector Standard SYSFAN 3-pin system cooler fan connector Standard CN_LVDS 20 x 2-pin LVDS connector Standard CN_INV 5-pin LCD inverter connector Standard CN_IR 5-pin IrDA connector Standard CN_COM34 10 x 2-pin COM3 & COM4 connector Standard CN_TV 4 x 2-pin TV-out connector (Only LV-673) Standard JFRNT 14-pin front panel switch/indicator connector Standard MINIPCI Mini-PCI socket Standard PEG PCI Express 16x/1x slot Standard CF CompactFlash Type I socket Standard CARDBUS PCMCIA Type II slot Standard 2.3.2 Connector Function Remark DC_IN DC 12V input connector Standard COM1/2 Serial port connector Standard USB_RJ45_A/B Dual USB and RJ45 LAN connector Standard VGA DB15 analog VGA connector Standard KB PS/2 keyboard connector Standard MS PS/2 mouse connector Standard AUDIO Audio connectors Standard

CPU & Memory Setup 16 2.4 2.4.1 The board comes with the socket479 for Intel Pentium M/Celeron M processors, it supports new generation of Intel Pentium M processors with 533MHz of front side bus and 2MB L2 cache. Please follow the instruction to install the CPU properly. 1. Use the flat-type screw drive to unlock the CPU socket Unlock way Check point 2. Follow the pin direction to install the processor on the socket 3. Lock the socket

Memory Setup 17 2.4.2 The board provides two 240-pin DDR2 DIMMs to support DDR2 400/533 memory modules up to 2GB of capacity. Non-ECC, unbuffered memory is supported only. While applying two same modules, dual channel technology is enabled automatically for higher performance. DDRIIB/A 112-pin 128-pin Please check the pin number to match the socket side well before installing memory module.

CMOS Setup 18 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values. Jumper: JRTC Type: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Normal Operation Default setting JRTC 1 3

Enhanced IDE Interface 19 2.6 The board has one UltraDMA33 IDE interface to support up to 2 ATAPI devices, and one CompactFlash Type I socket on the solder side, with jumper JCFSEL for IDE master/slave mode selection. Jumper: JCFSEL Type: onboard 3-pin header JCFSEL Mode 1-2 Master 2-3 Slave Default setting 2.7 Based on Intel ICH6-M, the board provides two Serial ATA interfaces with up to 150MB/s of transfer rate. SATA1 SATA2 IDE 44 1 2 43

Floppy Port 20 2.8 The board provides one slim type floppy port. FDD 4. Lift up this plastic bar 5. Slot the cable in (Blue paste for outside) 6. Press back the plastic bar Floppy rear side 1. Lift up the brown plastic bar 2. Slot the cable in (Blue paste for brown bar side) 3. Press back the plastic bar

Ethernet Interface 21 2.9 The board integrates with two Marvell E8053 PCI Express Gigabit Ethernet controllers, as the PCI Express 1x can speed up to 250MB/s of transfer rate instead of late PCI bus with 133MB/s of transfer rate. The Marvell E8053 supports triple speed of 10/100/100Base-T, with IEEE802.3 compliance and Wake-On-LAN supported. RJ45 LAN connector

Onboard Display Interface 22 2.10 Based on Intel 915GM(E) chipset with built-in GMA (Graphic Media Accelerator) 900 graphics, the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended desktop mode for CRT and LCD. The board also provides DVO port on PCI Express slot to support DVI interface with add on card. Notice: When you install any PCI Express Graphic card, the onboard graphics would be disabled automatically. 2.10.1 Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port. VGA

Onboard Display Interface 23 2.10.2 The board provides one 40-pin LVDS connector for 18-bit single/dual channel panels, supports up to 1600 x 1200 (UXGA) and 1920 x 1200 (WUXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting. CN_LVDS 1 2 39 40 1 5 CN_INV 1 3 JVLCD

Onboard Display Interface 24 Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 3-pin Power select Header Pin Description Pin Description 1 +12V 1 VCC 2 GND 2 LCDVCC 3 GND 3 VCC3 4 GND 5 ENABKL Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V Pin Signal Pin Signal 2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0- 8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1- 14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2- 20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 N/C 26 ACLK+ 25 N/C 28 GND 27 GND 30 N/C 29 BCLK- 32 N/C 31 BCLK+ 34 GND 33 GND 36 LVDDCLK 35 N/C 38 LVDDDAT 37 N/C 40 N/C 39 N/C

Onboard Display Interface 25 To setup the LCD, you need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight power. 3. A LCD cable and an inverter cable. For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables. LCD Installation Guide: 1. Preparing the LV-673(E), LCD panel and the backlight inverter. 2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V. 3. You would need a LVDS type cable. 4. To connect all of the devices well. For sample illustrator only Panel side Board side

Onboard Display Interface 26 After setup the devices well, you need to select the LCD panel type in the BIOS. The panel type mapping is list below: BIOS panel type selection form Single channel Dual channel NO. Output format NO. Output format 1 640 x 480 9 1024 x 768 2 800 x 600 10 1280 x 768 3 1024 x 768 11 1280 x 1024 4 1280 x 768 12 1366 x 768 5 1280 x 1024 13 1400 x 1050 @ 108Mhz 6 14 1400 x 1050 @ 122Mhz 7 15 1600 x 1200 8 16 1920 x 1200

Onboard Display Interface 27 2.10.3 LV-673(E) not supports TV out function. The board provides one HDTV interface up to 1024 x 768 resolution by NTSC/PAL supported, for three output types with Composite, S-Video and Component (YPbPr). Connector: CN_TV Connector type: 8-pin header TV-out connector (pitch = 2.54mm) Pin Number Assignment Pin Number Assignment 1 GND 2 S-Video/Y 3 S-video/Pr 4 GND 5 GND 6 GND 7 Composite/Pb 8 GND Notice1: This connector is for both S-Video/Composite and YPbPr outputs; please use attached two cables in the package for SDTV or HDTV devices. Notice2: S-Video and Composite can not be used at the same time. CN_TV 1 8

Integrated Audio Interface 28 2.11 The board integrates onboard audio interface with REALTEK ALC880 codec, with Intel next generation of audio standard as High Definition Audio, it offers more vivid sound and other advantages than former AC97 audio compliance. The main specifications of ALC880 are: z High-performance DACs with 100dB S/N ratio z 8 DAC channels support 16/20/24-bit PCM format for 7.1 audio solution z 16/20/24-bit S/PDIF-OUT supports 44.1K/48K/96kHz sample rate z Compatible with AC'97 z Meets Microsoft WHQL/WLP 2.0 audio requirements The board provides 7.1 channels audio phone jacks on rear I/O port, and amplified speaker out and Line-in/MIC-in ports for front I/O panel through optional cable. CN_AUDIO 1 10 SPDIF 1 CDIN 1 4 Rear I/O phone jacks LINE-IN LINE-OUT MIC-IN Center Rear Speaker Side Speaker

Integrated Audio Interface 29 Connector: CN_AUDIO Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header Pin Description Pin Description 1 MIC_L 2 Ground 3 MIC_R 4 Ground 5 Speaker_R 6 MIC Detect 7 SENSE 8 N/C 9 Speaker_L 10 Speaker Detect Connector: CDIN Type: 4-pin header (pitch = 2.54mm) Pin Description 1 CD – Left 2 Ground 3 Ground 4 CD – Right Connector: SPDIF Type: 4-pin header (pitch = 2.54mm) Pin Description 1 +5V 2 N/C 3 SPDIFOUT 4 GND

GPIO Interface 30 2.12 The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK. Connector: CN_DIO Type: 12-pin (6 x 2) 1.27mm x 2.54mm-pitch header Pin Description Pin Description 1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V CN_DIO 1 12

Power Supply 31 2.13 2.13.1 The board requires DC 12V input with 4-pin mini DIN connector on rear I/O panel, or onboard 4-pin ATX2.0 12V connector, the input voltage range is from 10.5V to 13V, for the input current, please take a reference of the power consumption report on appendix. Connector: PWRIN Type: 4-pin standard ATX2.0 +12V power connector Pin Description Pin Description 1 Ground 2 Ground 3 +12V 4 +12V Connector: DC_IN Type: 4-pin DC power connector Pin Description Pin Description 1 +12V 2 +12V 3 Ground 4 Ground PWRIN 1 2 3 4 DC_IN 1 2 4 3

Power Supply 32 2.13.2 The board provides one 4-pin AT connector for +5V/+12V output for powering your HDD, CDROM or other devices. Connector: CN_BPWR Type: 4-pin P-type connector for +5V/+12V output Pin Description Pin Description Pin Description Pin Description 1 +5V 2 Ground 3 Ground 4 +12V Note: Maximum output voltage: 12V/5A & 5V/3A CN_BPWR 1 4

Switch and Indicator 33 2.14 The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header Function Signal PIN Signal Function VCC 1 2 VCC IDE LED Active 3 4 N/C Reset 5 6 GND Power LED Reset GND 7 8 VCC N/C 9 10 N/C PWRBT 11 12 N/C Power Button 5VSB 13 14 SPKIN Speaker 1 14 JFRNT

Power Supply 34 Chapter 3 3.1

Video Memory Setup 35 Fixed + DVMT Memory Size: You can select the fixed amount and the DVMT amount at the same time for a guaranteed video memory and additional dynamic video memory, please check the table below for available setting. System Memory On-Chip Frame Buffer Size Fixed Memory Size DVMT Memory Size Total Graphic Memory 1MB 32MB 0MB 32MB 1MB 0MB 32MB 32MB 8MB 32MB 0MB 32MB 128MB~255MB 8MB 0 32MB 32MB 1MB 64MB 0MB 64MB 1MB 0 64MB 64MB 1MB 128MB 0MB 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0MB 64MB 8MB 0 64MB 64MB 8MB 128MB 0MB 128MB 8MB 0 128MB 128MB 256MB~511MB 8MB 64MB 64MB 128MB 1MB 64MB 0 64MB 1MB 0 64MB 64MB 1MB 128MB 0 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0 64MB 8MB 0 64MB 64MB 8MB 128MB 0 128MB 8MB 0 128MB 128MB 512MB upper 8MB 64MB 64MB 128MB Notice: 1. The On-Chip Frame Buffer Size would be included in the Fixed Memory. Please select the memory size according to this table.

Video Memory Setup 36 Chapter 4 The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems. The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting. The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen. To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press ＜Enter＞ key to accept the selection and enter the sub-menu. Figure 4-1 CMOS Setup Utility Main Screen

BIOS Setup 37 (This Page is Left for Blank)

38 Appendix A A.1 Connector: IDE1 Type: 44-pin (22 x 2) box header Pin Description Pin Description 1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 -IOW 24 Ground 25 -IOR 26 Ground 27 IORDY 28 Ground 29 DACK 30 Ground 31 IDEIRQ 32 IDE32 33 A1 34 P66DET 35 A0 36 A2 37 -CS1 38 -CS3 39 -HD LED1 40 Ground 41 +5V 42 +5V 43 Ground 44 Ground 1 2 43 44