ProFusion PS-10241 Owner's Manual

OWNER’S MANUAL PS-10241WP 10KW 240V 60Hz 1P PS-30483W 30KW 480V 60Hz 3P IMPORTANT INSTRUCTIONS READ & SAVE Technical support: 1-866-206-0888 Service email: [email protected] all-guides com

Important Instructions………………………………………3-4 Specifications and Wiring Diagram………………………5-7 Parts of the heater ……………………….………………….8 Installing Instructions……………………….…………..….9-11 Operating Instructions……………………….………....…..12 Maintenance and Cleaning…………………………………13 Warranty Information ……………………………………….13

HEATER NOTE: There may be a trace of smoke or odor when unit is first operated. Don’t be alarmed. This indicates that a drop of oil fell on the heating coil during the manufacturing process. It will quickly evaporate and should not re-occur. Make sure that the room in which the appliance is located is well ventilated during this operation. It is normal for the appliance to emit small cracking sounds when you turn it on for the first time. Do not be alarmed. WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE, ELECTRICAL SHOCK AND INJURY TO PERSONS OR PROPERTY, INCLUDING THE FOLLOWING: 1) Read all instructions before using this heater. 2) This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3’ (0.9 m) from the front of the heater and keep them away from the sides and rear. 3) Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. 4) Always switch off the heater when not in use. 5) Do not operate any heater after the heater malfunctions, has been dropped or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing. 6) Do not use outdoors. 7) To disconnect heater, turn off power to heater circuit at main disconnect panel. 8) Do not install less than 6 feet (1.8m) high from the floor and keep the mounting bracket not less than 4 feet (1.2m) away from

from the back wall (with or without using the wall hanging mounting bracket). 9) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 10) To prevent a possible fire, do not block air intakes or exhaust in any manner. 11) A heater has hot and arcing or sparking parts inside. To reduce the risk of fire, do not use it in areas where gasoline, paint, or flammable vapors and liquids are used or stored. 12) Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. 13) This product must be installed by a certified electrician, in accordance with local codes. 14) Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. 15) This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. CAUTION – High temperature, risk of fire, keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the heater and away from the side and rear. PET OWNERS WARNING: The health of some small pets including birds are extremely sensitive to the fumes produced during the first-time use of many appliances. These fumes are not harmful to humans but we recommended that you do not use your heater around birds and small pets during its initial use until the manufacturing corrosion coatings burn off. SAVE THESE INSTRUCTIONS

Model: PS-10241 MANUFACTURER No.: PS-10241WP Volt: 240 V, 1P Watts: 10KW Frequency: 60 Hz Wiring diagram: SPECIFICATIONS

Volt: 480 V, 3P Watts: 30KW Frequency: 60 Hz Wiring diagram: all-guides com

Open the cover. After connection. Earth Wire L2 (Live Wire2 Black) L3 (Live Wire3 Red) L1 (Live Wire1 White)

B. Hanger C. Heater Housing D. Front Exhaust Grill E. ON/OFF Switch F. Temperature Setting Knob PARTS OF THE HEATER A C D F E B

according to the electrical safety. The heater must be grounded in accordance with all national and local building codes. All Wiring procedures and connections shall be in accordance with the national and local codes having jurisdiction. Before installation: Disconnect the main supply connection. The heater must be connected to individual branch circuit protected by 65 Amp circuit breaker only. Supply cables must be equipped with a dual pole circuit breaker rating at least 240V 65A/pole as main cutoff switch of power connection to the heater. CAUTION: High temperature, risk of fire, keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the heater and away from the side and rear. WARNING: To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. INSTALLATION INSTRUCTION: 1. Keep the unit at least 6 feet (1.8m) away from the floor. This minimum distance must be maintained. 2. Do not install closer than 4 feet (or 1.2 m) to any adjacent vertical surfaces or walls. 3. Keep at least 4.5 inches (11.5cm) from the back wall (with or without using the wall hanging mounting bracket). 4. Mark the drill-hole positions in the wall for the mounting bracket. 5. Drill the required holes with diameter fit for the anchor provided for positioning the mounting bracket. 6. Insert the anchors. 7. Attach the mounting bracket to the wall and secure with mounting screws. INSTALLING INSTRUCTIONS

and rubber pads, tighten the screws. 9. Insert the hexagon head screw through the hanger and the mounting bracket, tighten the nut.

connect to the wiring compartment 12. Make the connections properly with connectors which are suitable for the conductor size, including grounding wirings. And after making the connections, arrange the pigtail leads of unit and power supply wires in the wiring compartment. all-guides com

used. HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH :  Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E.  A circuit breaker must be installed and serviced only by qualified electrical personnel.  Always use a properly rated voltage sensing device to confirm power is off.  Switch the ON/OFF switch to ON position to turn on the heater. Then turn the thermostat to the farthest clockwise position. The fan should start and the unit begins heating the room, and lamp is light. After the room reaches comfort level, turn the thermostat counterclockwise until the heater shuts off. The heater will automatically cycle around this preset temperature. To increase the temperature, turn the thermostat knob clockwise. To lower the temperature, turn the thermostat counterclockwise.  Select a thermostat setting. Ambient temperature is regulated by adjusting the thermostat to a desired position. Allow the unit to operate and warm up the room. When the desired temperature is reached, turn the control knob counterclockwise until the heater turns off. This is your ideal setting. The heater will start automatically when the room temperature drops below this set point, and will turn off when the set point is reached.  To turn off the heater, switch the ON/OFF switch to OFF position. OPERATING INSTRUCTIONS

following description. All other servicing or maintenance should be performed by qualified service personnel. Before any cleaning, make sure that: 1. Disconnect power supply at source. 2. Wait for 60 minutes to ensure the heating element has cool down, and your heater is now ready for cleaning. Regular Cleaning: 1. Do not use cleaning liquid or other chemicals to spray on the unit. 2. Interior dust can often be removed by using a vacuum cleaner with a crevice tool attachment. 3. To clean enclosure, use a clean, soft and lightly damp cloth to gently wipe off the dirt from the surface of the unit. Be sure not to wet the heating element and the switches. Allow the unit to dry completely before using it. CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF THE HEATER AS THIS COULD CREATE A FIRE OR ELECTRIC SHOCK HAZARD, DAMAGING THE UNIT. This product carries a one (1) year warranty against defects in workmanship and materials. Profusion Heat agrees to replace a defective product, within the stated warranty period, when returned to the place of purchase with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. MAINTENCE AND CLEANING INSTRUCTIONS(separate page) WARRANTY INFORMATION