Peak PCAN-Router Pro FD Operation & User’s Manual

45 Digital Outputs High-side Low-side Maximum output current (current limitation) 0.7 A minimal 1.5 A typically 2.4 A maximum 1.2 A minimal 1.8 A typically 3 A maximum Protection Overcurrent (0.7 - 2.4 A) and temperature protection (150°C) Overcurrent (1.2 - 3 A) and temperature protection (165°C) Maximum voltage max. 32 V on load Power Supply Supply voltage 12 V DC, 8 to 30 V DC possible Current consumption Idle: 400 mA Maximum: 1 A Current consumption Sleep mode 12 V, 25°C: 230 μA Maximum: 350 μA Wake-up voltage 3 to 32 V DC at pin 1 of the power conne ...

21 8. Push the board back into the first rail of the housing. 9. Replace the housing cover and the back panel. 10. Only with optional BroadR-Reach® interface: Fasten the two screws of the D-Sub connector to the rear of the housing. 11. Reinsert all eight housing screws. Important note: Only use batteries with integrated PCB protection to avoid short circuit, overcharging, and deep discharge! We recommend using a lithium-ion battery such as the Soshine 18650 3600 mAh 3.7 V or comparable models. ...

25 1. Turn the ID rotary switch on the back of the housing to position F. Use a slotted screwdriver, for example. Figure 11: Turn the rotary switch on the rear of the housing to F. 2. Restart the device by interrupting the power supply for the change of the rotary switch to take effect. 3. Connect the CAN interface of your computer to a CAN connector on the PCAN-Router Pro FD. Note: The firmware upload is possible with each of the 6 CAN channels. The selected CAN channel must be connected alone to the PC. 6.3 Firmware Transfer Do the following to transfer a n ...

37 7.2.9 Timeouts With these settings timeouts are specified in milliseconds. No CAN traffic TRC_STOP_TRAFFIC_TO specifies a timeout for no CAN traffic. If no CAN message was received for this duration, tracing is stopped. TRC_STOP_TRAFFIC_TO=0 Terminal 15 Loss TRC_STOP_T15_TO specifies a timeout for terminal 15 loss. If power at the pin 1 of the power connector was lost for this duration, tracing is stopped. TRC_STOP_T15_TO=0 Main Power Loss TRC_STOP_MAINPOW_TO specifies a timeout for main power loss. If the main power was lost for this duration, tracing is ...

43 8 Technical Specifications Connectors CAN 6 x D-Sub (m), 9 pins Assignment according to specification CiA® 303-1 USB USB port type C Superspeed USB 3.0 Upstream Inputs/outputs Phoenix mating connector MC1.5/2-STF-3.81, 6-pin; 2 x digital input or output with high-side switch 2 x digital input or output with low-side switch 1 x analog input (0 - 33 V) Power Phoenix mating connector MC1.5/2-STF-3.81, 3-pole; overvoltage and reverse polarity protection Ethernet or D-Sub (optional) RJ-45 or BroadR-Reach® interface available on request only; self-created f ...

36 Option Description EMMC The internal eMMC memory card is used for tracing. This value is the default setting. 7.2.7 Handling of the USB Connection This setting specifies how an existing USB connection is handled when tracing is started. TRC_KICK_USBC=YES Option Description YES The USB host is disconnected when tracing is started. In that case a running USB data transfer would be canceled. This value is the default setting. NO The USB host is not disconnected. Tracing can only be started if the USB cable was disconnected before. Note: For reading the config ...