pagertec Alpha TXT Operation & User’s Manual

Thank you for choosing Pagertec as your provider for your wireless paging requirements. is providing you with total customer satisfaction. Please take a few minutes to review this manual prior to installing and operating your system. The manual will provide you with installation instructions, and offer suggestions to ensure you receive all of the many Pagertec has the most responsive customer service available within the industry. Please do not hesitate to contact out Customer Care, if you have any questions. We look forward to a long and mutually rewarding partnership.

INSTALLATION 1.- EQUIPMENT SETUP (1) Wireless Call buttons Unwrap all sending unit (Wireless Call button)components. Plug the power supply with the large tip into a standard outlet and plug it into the “Charger Base” for Call button transmitters. Stack the Call Buttons on the charger base. The red indicator will turn on to indicate the call buttons are charging properly. We recommend some type of surge protector on the power supply for protection. Power surges are not covered under system warranty. (2) Alpha TXT Pagers Locate the charger base for the pagers, place it in a sturdy out of way area. Connect the charger base to the power with the provided power supply. Insert the pagers on the charger base. The pager number will always face up and the red charging light indicator will turn on to indicated pager is charging properly. You should check for charging indicator to appear on each pager. On the top of each pager is your pager number.

Place the Wireless Call Button transmitter in the proper location. The Call button comes included with a Velcro sticker that you can stick onto the surface you wish to keep the call button at. Be sure that transmitter is not in the way and that it is not easily dropped by mistake. Check the Call button number matches the number of area or table. This number will be displayed on the pager every time it is pressed to alert the user from where they are being called. (2) Alpha TXT Pager Attach the pager on the employees belt using its belt clip. Be sure that there is message on the pager. Normally it will say “Pagertec” or it will say the name of your business. if it does not display anything the pager might be off and may need more charging time. Velcro 3M Sticker Call Button Number

1. The pager after a full charge should always be “ON” 2. The paging system will come already paired with your call buttons. 3. The Alpha TXT pager will display “Call Button Number”- Message EX: 5 - Manager Needed ( This means that from call button number #5 they pressed the 4) The Alpha TXT pager can save and store the last 5 messages it received. To view the messages press and hold the button on the side of the pager for 3 seconds. To continue to scroll press the button again for 1 second. This way you can scroll through all the messages stored. Press and hold for 3 seconds.

the call button it received the page from and pressing “Cancel”. This helps the user keep track of the tasks may or may not need attention. 6) To clear all the messages from the pager the master erase is activated by placing the pager on the charging station for 5 seconds. This will clear out and saved messages on the pager. Note: If your system has a cancel button the pager will not receive a cancel page unless it has received and stored another message from the same call button. In other words it can only receive a cancel message if it has received a previous message from the same call button. Wireless Call Button: There are several version of the call button 1,3, and 5 buttons.\ The call button should have a label with a message for each number. This will let the user know which button they will need to press. Ex: 1- Tech 2- Manager 3- Service 4- Temperature 5- Cancel This indicates that if the user presses 2 the corresponding pager will show “Manager” to let them know a manager is needed. The messages are customized for each one of our clients. The screen will display 12 characters and if the message is longer than then the screen will scroll to show the rest of the message.

pressed. This means the call button is sending a signal to a pager. 4. If you call buttons are rechargeable the Call Buttons usually have a 4-6 month battery life. It is recommended to charge them once every 3 months to keep battery at an optimal level. CLEANING Pagertec pagers are made from industrial-strength, polycarbonate material. However, this material is susceptible to hairline cracking if non-approved cleaners are used. When cleaning Pagertec pagers, you should only use ETHYL ALCOHOL (ethanol) or ISOPROPYL ALCOHOL-BASED CLEANERS. We have done extensive testing with available cleaning materials and have not found any issues with either ethyl alcohol (ethanol) or isopropyl alcohol (IPA). ALL other cleaners are not recommended for use on any of our pagers. To clean the equipment: 1. Take a clean cloth and an isopropyl-alcohol based cleaner 2. Wet the clean cloth with the isopropyl alcohol cleaner 3. Wipe down the pagers or equipment 4. When dry, place rechargeable pagers back on charge

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1. Reorient the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. in the instruction manual. WARNING: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. CAUSION: for compliance could void your authority to operate the equipment.