Neteon GW312 Quick Start Manual

GW312/GW315 2-Port Ethernet Serial Server Version 1.2 Updated on 2018/12/21 Toll Free: 1-888-908-3330 Tel: 1-732-568-1988 Email: [email protected] www.neteon.net

Ethernet Serial Server GW312/GW315 Copyright © 2006 Neteon Technologies, Inc. All rights reserved. Designed in Taiwan. 1 This document intends to provide customers with brief descriptions about the product and to assist customers to get started. For detail information and operations of the product, refer to the product user’s manual in the product CD. 1. Packaging Check your package contains the following items: GW312/GW315 Serial-Ethernet Server  Quick Start Guide  Product CD  Wall mounting screws  3-pin terminal block for power input (only for GW315)  5-pin terminal block with lock*2 (only for GW315)  Power Adapter - DC Jack 12VDC,1.25A with Lock (only for GW312)  Optional Accessories： -Din Rail Kit DK-25 2 Hardware Description NOTE: 1. GW312 (for RS-232/422/485 without isolation ), GW315 (for RS422/485 with isolation) 2. Press the reset button of GW312/GW315 to reset to the default value Fig. 1 shows the interface Fig. 1. GW312/GW315 interfaces

Ethernet Serial Server GW312/GW315 Copyright © 2006 Neteon Technologies, Inc. All rights reserved. Designed in Taiwan. 2 LED Indicators: LAN LED Message Description Off Ethernet Disconnected Blinking with Green Data transmitting on Ethernet at 100Mbps Blinking with Orange Data transmitting on Ethernet at 10Mbps Table 1. LAN LED Message COM Port LED Message Description Off No data transmitting on COM port Com 1(2)TX Blinking Data transmitting on COM port Com 1(2)RX Blinking Data Receiving on COM port Table 2. COM Port LED Message RUN LED Installation Procedures: Step 1: Connect GW312/GW315 to power source Step 2: Connect GW312/GW315 to the Ethernet network. Use a standard straight-through Ethernet cable when connect to a hub/switch, or connect to a PC‘s Ethernet port via a cross-over Ethernet cable. However, Always make sure your PC is on the same network sub-net as GW312/GW315. Step 3: Connect GW312/GW315’s serial port to a serial device. Step 4: Mount GW312/GW315 to a wall/panel with the screws included or Din-Rail rack (Require optional item model: Din-Rail-Kit). 3 Software Setup Default Network Setting: Default User Name/Password: IP: 10.0.50.100 User Name: admin Gateway: 10.0.0.254 Password: default Subnet: 255.255.0.0 Auto IP (Dynamic IP): A DHCP server can automatically assign the IP address and all the network settings. GW312/GW315 supports the DHCP client function. By default, the DHCP client function on GW312/GW315 is disabled; you may activate the DHCP client functions by executing management.exe (Fig. 2) Fig. 2. management.exe utility Dialog Window Assign a Static IP address by: Message Description On Jumper JP1 Pin1 and Pin2 are shorted to disable AP firmware Blinking (rate: 0.5 Sec) AP firmware running normally Table 3. RUN LED Message

Ethernet Serial Server GW312/GW315 Copyright © 2006 Neteon Technologies, Inc. All rights reserved. Designed in Taiwan. 3 A Configuration by Telnet 1. Telnet to GW312/GW315 using DOS command “Telnet IP_address”. Example: telnet 10.0.50.100 2. GW312/GW315’s network, link mode and COM ports settings can be configured in the telnet window B Configuration by Management.exe Utility Use Management.exe on Product CD to configure the GW312/GW315.First click” Config” then assign a static IP. C. Configuration by Web Browser 1. Make sure the PC is on the same network as GW312/GW315 2. Open a web browser, then Enter in the IP address as the GW312/GW315. The default user name is admin and default password is default. 3. The GW312/GW315’s network, link mode and COM ports settings can be configured on different web pages. 4. Click “Save Configuration” to save settings. 5. Click ”Restart” button to initiate the change. 4 Pin Assignments The pin assignments of DB9 connector on GW312 is shown in the following table: Pin# RS-232 Full Duplex for GW312 Model RS-485 2 wire, Half Duplex for GW312 Model RS-485/RS-422 4 wire, Full Duplex for GW312 Model 1 DCD N/A N/A 2 RXD N/A (reserved) TXD+ 3 TXD DATA+ RXD+ 4 DTR N/A N/A 5 SG (Signal Ground) SG (Signal Ground) SG (Signal Ground) 6 DSR N/A N/A 7 RTS DATA- RXD- 8 CTS N/A(reserved) TXD- 9 N/A N/A N/A The pin assignments of Terminal Block connector on GW315 is shown in the following table: Pin# RS-485/RS-422 4 wire, Half Duplex For GW315 RS-485 2 wire, Full Duplex For GW315 1 T+ NC 2 T- NC 3 R+ Data+ 4 R- Data- 5 SG (Signal Ground) SG (Signal Ground) Customer Services and Supports Telephone: Toll Free 1-888-908-3330, Outside USA: +1-732-568-1988 Email: [email protected] Web: www.neteon.net