RSI SMARTCANOPY Assembly Instructions Manual

LIKE SHARE FOLLOW PLEASE ENSURE TO READ ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL.

7 ASSEMBLY KIT CONTENT (HARDWARE) DESCRIPTION QTY EXAMPLE COMPONENTS FLAT DECK 1 ASSEMBLY KIT CONTENT (COMPONENTS) ASSEMBLY KIT CONTENTS 1 M6 FLAT WASHERS 11 HEADER BOARD 1 DOCUMENT REVISION 2. GUSSET 2 M6 X 16 BUTTON HEAD SCREWS 4 M10 X 30 SET SCREWS 8 M10 X 30 FENDER WASHERS 16 Nyloc Nut M10 8

NO. 10 FLAT WARNING AND REQUIRED TOOLS 2 Torque Wrench WARNING LABELS Ensure that only the recommended tools are used during the assembly procedure of the RSI SMARTCANOPY to avoid damaging the RSI SMARTCANOPY. Take note to the symbols indicating possible safety hazards during assembly and to use the relevant personal protective equipment and safety measures as indicated. Pinch Hazard Please Keep Hands & Fingers Safe Heavy Load Please Lift Correctly Electrical Hazard Please Use Caution WARNING ! !

! 1. ONLY USE THE RECOMMENDED TOOLS AS INDICATED IN THE FITMENT INSTRUCTION ON THE PAGE BEFORE 2. ONLY USE THE HARDWARE PROVIDED IN THE ASSEMBLY KIT OUTLINED ON THE PAGE BEFORE 3. HANDLE ALL RSI SMARTCANOPY COMPONENTS WITH CARE UPON UNPACKING 4. TO AVOID SCRATCHING DO NOT PLACE RSI SMARTCANOPY COMPONENTS ON A ROUGH SURFACE 5. NEVER USE ACETONE ON PAINTWORK 3 STEP ONE 1. REMOVE THE COMPONENTS FROM THE PACKAGING AND PLACE SOMEWHERE SAFE OUT OF HARMS WAY. 2. BE CAREFUL NOT TO DAMAGE ANY COMPONENTS. 3. INSPECT FOR ANY DAMAGE THAT MIGHT HAVE OCCURRED DURING SHIPPING., REPORT DAMAGE IMMEDIATELY WHEN NOTICED. WARNING: PLEASE ADHERE TO GUIDE TO PREVENT DAMAGE TO RSI SMARTCANOPY DURING ASSEMBLY. STEP TWO 1. PLACE THE DECK RIGHT WAY UP ( AS IF IT WAS BEING FITTED TO A VEHICLE). 2. BOLT ON THE HEADER BOARD USING THE HARDWARE DEPICTED IN THE IMAGES BELOW. 3. USE A SQUARE TO ENSURE THE HEABERBOARD IS BOLTED ON STRAIGHT. 4. PLEASE NOTE THERE ARE 7 MOUNTING POSITIONS. M6 NYLOC NUT. M6 FLAT WASHER. RIV STUDS FROM HEADER BOARD. PLEASE NOTE THERE ARE 7 FIXING POINTS.

2. ONLY USE THE HARDWARE DEPICTED BELOW, WORK WITH CAUTION TO AVOID ANY UNNECESSARY FORMS OF DAMAGE. 3. FASTEN ALL FIXING SUFFICIENTLY. ENSURE HEADERBOARD IS SQUARE(90 DEGREES). ASSEMBLY OF THE RSI SMARTDECK M10 NYLOC NUTS. M10 X 30 FENDER WASHERS. M10 X 30 FENDER WASHERS. M10 X 30 SET SCREWS WITH M10 X 30 FENDER WASHERS. M6 X 16 BUTTON HEAD SCREWS. GUSSETS. M6 X 16 FENDER WASHERS. GUSSETS. GUSSET BOLTING PROCESS.

GUSSETS BOLTED IN PLACE. STEP FOUR 1. ONCE YOU HAVE REACHED THIS STEP PLEASE MAKE SURE THAT THE HEADERBOARD IS STRAIGHT AND SQUARE, THEN MAKE SURE ALL FIXINGS ARE SUFFICIENTLY TIGHTENED, EVEN THE BOLTS HOLDING THE GUSSETS IN PLACE. 2. THIS IS A CRITICAL STEP, BEACAUSE ONCE THE RSI SMARTDECK IS FITTED, YOU WONT GAIN ACCESS TO THESE BOLTS. 3. PLEASE USE CAUTION WHEN TIGHTENING BOLTS TO PREVENT UNNECESSARY DAMAGE TO THE RSI SMARTDECK. RSISMARTCANOPY SMARTCANOPY DBN 031 700 5925 CPT 021 981 2301 JHB 011 974 0370 THANK YOU FOR PURCHASING A RSI SMARTDECK. SHOULD YOU HAVE ANY ENQUIRIES ABOUT THE ASSEMBLY, FEEL FREE TO CONTACT US