Romik RAL Installation Instructions Manual

Installation Instructions Part No. 2614 Product: Running Boards Application: Jeep GC 2011 – 2020 all Except Summit Dodge Durango 2011+ Level of Difficulty: 1 2 3 4 5 Installation Time: 60 Min Hardware Torque Specifications M6 Bolt 3 ft-lbs. M8 Bolt 7 ft-lbs. M10 Bolt 16 ft-lbs. M12 Bolt 28 ft-lbs. ATTENTION: Use correct torque settings to avoid damaging the running boards and or mounting brackets. Failure to do so will void your warranty. If you have any questions please contact our technical team at 1-866-717-6645

Installation Instructions Part No. 2614 Product: Running Boards Application: Jeep GC 2011 – 2020 Summit Level of Difficulty: 1 2 3 4 5 Installation Time: 60 Min Hardware Torque Specifications M6 Bolt 3 ft-lbs. M8 Bolt 7 ft-lbs. M10 Bolt 16 ft-lbs. M12 Bolt 28 ft-lbs. ATTENTION: Use correct torque settings to avoid damaging the running boards and or mounting brackets. Failure to do so will void your warranty. If you have any questions please contact our technical team at 1-866-717-6645

NOTE: Jeep Grand Cherokee models visible gap due to body shape of the vehicle, if not sure stop before installing and visit www.Romik.com to review images Step 1: Locate front mounting locations and hardware as per 1st page of this installation manual Dodge Durango models and all Jeep GC models. For Summit models please pay attention to step 4 Step 2: Remove plug #2 starting from front to back see Figure 1 Step 3: Install provided HTC 230 as shown Figure 2 Step 4: Install bracket top part using supplied M6 hardware Figure 3. Step 5: Install bracket lower portion using supplied M10 hardware Figure 4. Note for Summit models front bracket position is very important. Video Installation Instruction: HTC 230 Figure 1 Figure 2 Figure 3 Figure 4 M6 M10

Step 6: Locate middle bracket install are and remove rubber plug #3 Figure 5. Step 7: Install supplied HTC 230 as shown Figure 6. Step 8: Install bracket top part using supplied M6 hardware Figure 7. Step 9: Install bracket lower portion using supplied M10 hardware Figure 8. Step 9: Locate rear bracket install are and remove rubber plug #5 Figure 9. Step 10: Install supplied HTC 230 as shown Figure 10. Step 11: Install bracket top part using supplied M6 hardware Figure 11. Figure 5 Figure 6 HTC 230 M10 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 HTC 230 M6 M6 Video Installation Instruction:

Step 12: Install bracket lower portion using supplied M10 hardware Figure 12. Step 13: Proceed to last page of this manual for running board install instructions and torque values NOTE: We recommend that you place a level on top of the running boards to assist you before finalizing the installation. For Technical support please call our team at 1-866-717-6645 and one of our experts will assist you with this installation. Thank you for choosing Romik. Figure 12 M10

1) Flip your Romik running boards onto a flat surface, make sure to place the running boards on a towel or cardboard in order to protect the surface Figure 1. 2) Loosen the M8 bolts on back of your running boards Figure 2. Depending on your model there Will be either 6 or 8 bolts installed per side. 3) Once your brackets have been installed, place the running board onto the brackets as shown on Figure 3. 4) Adjust running boards, centering on vehicle. Hand tight M8 hardware on running boards. 5) Follow the torque procedures, torque M8 hardware to 7 ft-lbs using a torque wrench. 6) Cleaning and maintaining your running boards is important, apply a light coat of a quality carnauba wax at least 2X per year. Wash often with mild soap and make sure to remove all soap Residue. Many car automatic carwashes use a strong soap, make sure to use enough water to remove all residue. 7) Register your products at www.Romik.com/contact/productregistration 8) Warranty information at www.Romik.com/warranty