Romik 2137 2D Installation Instructions Manual

Installation Instructions Part No. 2137 2D / 3D Product: Romik Connect Running Boards Application: Ford Transit 2014+ Level of Difficulty: 1 2 3 4 5 Installation Time: 90 Min Hardware Torque Specifications M6 Bolt 3 ft-lbs. M8 Bolt 7 ft-lbs. M10 Bolt 16 ft-lbs. M12 Bolt 28 ft-lbs. ATTENTION: Use correct torque settings to avoid damaging the running boards and or mounting brackets. Failure to do so will void your warranty. If you have any questions please contact our technical team at 1-866-717-6645

Step 1: Locate mounting locations and hardware as per 1st page of this installation manual Step 2: Pre-assemble front drivers bracket for easy installation. If equiped with mudflaps remove screw holding mudflap bracket as shown on Figure 1. This will be reused. If the vehicle does not have mudflaps proceed from Figure 2. Install provided HTC 243 and M10 bolt as shown Figure 3. Install pre-assembled bracket as shown on Figure 4 Step 3: Pre-assemble rear drivers bracket, Install provided HTC 243 as shown Figure 5 Step 4: If vehicle is equiped with rear ac. Remove factory screw (will be re-used) Figure 6. If vehicle does not have rear ac proceed to install HTC 226 Figure 7. Proceed to install pre-assembled bracket as shown Figure 8. Do not tighten. Video Installation Instruction: Figure 1 Figure 2 Figure 3 Figure 4 HTC 243 Figure 5 Figure 6 Figure 7 Figure 8 HTC 226 HTC 243 M10

Step 5: Pre-assemble passenger side front bracket. Locate mounting points and install provided HTC 243 and M10 bolt If equiped with mudflaps please review step 2 . Step 6: Install pre-assembled bracket do not tighten Step 7: Pre-assemble bracket pass second bracket as shown on Figure 11, install provided HTC 243 as shown on Figure 12. Install pre-assembled bracket as shown on Figure 9. Do not tighten Step 8: Middle brackets do not require pre-assembly clean factory threads Figure 12 and install using supplied M8 hardware. Note some models do not have threaded inserts on bottom mount and may require tapping to M8 25 proceed to install do not tighten Figure 9 Figure 10 HTC 243 M10 Figure 12 Figure 12 HTC 243 Figure 11

Step 9: Note: If your vehicle is a short wheel base please skip to Step 9. Pre-assemble last bracket and install provided HTC 243 as show Figure 13. Install pre-assembled bracket Figure 14 do not tighten Step 10: This step is for short wheel base models only, if you have completed step 8 please proceed to step 10, install provided HTC 243 and attach bracket Figure 15. Do not tighten Step 11: Proceed to last page of this manual for running board install instructions and torque values For Technical support please call our team at 1-866-717-6645 and one of our experts will assist you with this installation. Thank you for choosing Romik. Figure 13 Figure 14 Figure 15 HTC 243 HTC 243

Please follow these steps to successfully “join” the 2 PC running boards together. Step 1: Remove products from box and placed on a soft surface to avoid scratching. Step 2: Remove plastic endcap as shown on Figure A1 – A4 keep screws as they will be re-used. Step 3: Remove Romik Connect plate and assemble as show on Figure B1 – B3 using original screws. Join two running boards together using supplied M8 bolts torque to 7 ft lbs. Step 4: Install running boards as per last page of this manual.

1) Flip your Romik running boards onto a flat surface, make sure to place the running boards on a towel or cardboard in order to protect the surface Figure 1. 2) Loosen the M8 bolts on back of your running boards Figure 2. Depending on your model there Will be either 6 or 8 bolts installed per side. 3) Once your brackets have been installed, place the running board onto the brackets as shown on Figure 3. 4) Adjust running boards, centering on vehicle. Hand tight M8 hardware on running boards. 5) Follow the torque procedures, torque M8 hardware to 7 ft-lbs using a torque wrench. 6) Cleaning and maintaining your running boards is important, apply a light coat of a quality carnauba wax at least 2X per year. Wash often with mild soap and make sure to remove all soap Residue. Many car automatic carwashes use a strong soap, make sure to use enough water to remove all residue. 7) Register your products at www.Romik.com/contact/productregistration 8) Warranty information at www.Romik.com/warranty