Romik 1619-2D Installation Instructions Manual

Installation Instructions Part No. 1619-2D/3D Product: Romik Connect Running Boards Application: Dodge RAM ProMaster 2014+ Level of Difficulty: 1 2 3 4 5 Installation Time: 90 Min Hardware Torque Specifications M6 Bolt 3 ft-lbs. M8 Bolt 7 ft-lbs. M10 Bolt 16 ft-lbs. M12 Bolt 28 ft-lbs. ATTENTION: Use correct torque settings to avoid damaging the running boards and or mounting brackets. Failure to do so will void your warranty. If you have any questions please contact our technical team at 1-866-717-6645

Step 1: Separate brackets and hardware as per 1st page of this installation manual. Please note bracket positioning for Long Wheel Base 5,8,2,1 and Short Wheel Base models 5,8,1,2. Step 2: Driver’s side front, remove factory rubber plugs as shown on Figure 1 TIP: Try to preassemble the bracket for easier placement. Install provided HTC 243 Step 3: Bring pre-assembled bracket and install onto HTC 243 and secure, push clamp end onto the vehicle chassis lip push up and secure Figure 2. Do not tighten at this time since the board will help level the bracket. Step 4: Pre-assemble Driver’s rear bracket as shown Figure 3 Install supplied HTC 243 as shown Step 5: Bring pre-assembled bracket and install onto HTC 243 Figure 4 and secure Do not tighten at this time since the board will help level the bracket. Video Installation Instruction: HTC 243 Figure 1 Figure 2 Figure 3 HTC 243 Figure 4

Step 6: Pass Front, remove factory rubber plugs as shown on Figure 5 pre-assemble the bracket for easier placement. Install provided HTC 243 Step 7: Bring pre-assembled bracket and install onto HTC 243 and secure, push clamp end onto the vehicle chassis lip push up and secure Figure 6. Do not tighten at this time since the board will help level the bracket. Step 8: Pre-assemble bracket as shown on Figure 7, install provided HTC 243 as shown on Figure 8. Install pre-assembled bracket as shown on Figure 9. Do not tighten NOTE: If you are only installing front driver and front passenger running boards please proceed to Step 10 and install the running boards. Step 9: Pre-assemble Pass 3rd bracket Figure 10, install HTC 243 on shown locations Figure 11. Attach pre- assembled bracket as shown on Figure 12. Do not tighten Please note bracket positioning for Long Wheel Base 5,8,2,1 and Short Wheel Base models 5,8,1,2. HTC 243 Figure 5 Figure 6 Figure 10 Figure 11 Figure 12 HTC 243 Figure 7 Figure 8 Figure 9

Step 8: Pre-assemble Pass 3rd bracket Figure 13, install HTC 243 on shown locations Figure 14. Attach pre- assembled bracket as shown on Figure 15. Do not tighten Please note bracket positioning for Long Wheel Base 5,8,2,1 and Short Wheel Base models 5,8,1,2. Step 9: Install pre-assembled 3rd bracket as shown on Figure 15 Do not tighten Step 10: Proceed to last page of this manual for running board install instructions and torque values For Technical support please call our team at 1-866-717-6645 and one of our experts will assist you with this installation. Thank you for choosing Romik. HTC 243 Figure 13 Figure 15 Figure 14

Please follow these steps to successfully “join” the 2 PC running boards together. Step 1: Remove products from box and placed on a soft surface to avoid scratching. Step 2: Remove plastic endcap as shown on Figure A1 – A4 keep screws as they will be re-used. Step 3: Remove Romik Connect plate and assemble as show on Figure B1 – B3 using original screws. Join two running boards together using supplied M8 bolts torque to 7 ft lbs. Step 4: Install running boards as per last page of this manual.

1) Flip your Romik running boards onto a flat surface, make sure to place the running boards on a towel or cardboard in order to protect the surface Figure 1. 2) Loosen the M8 bolts on back of your running boards Figure 2. Depending on your model there Will be either 6 or 8 bolts installed per side. 3) Once your brackets have been installed, place the running board onto the brackets as shown on Figure 3. 4) Adjust running boards, centering on vehicle. Hand tight M8 hardware on running boards. 5) Follow the torque procedures, torque M8 hardware to 7 ft-lbs using a torque wrench. 6) Cleaning and maintaining your running boards is important, apply a light coat of a quality carnauba wax at least 2X per year. Wash often with mild soap and make sure to remove all soap Residue. Many car automatic carwashes use a strong soap, make sure to use enough water to remove all residue. 7) Register your products at www.Romik.com/contact/productregistration 8) Warranty information at www.Romik.com/warranty