Rockwell DELTA Manual 

PM-1886 400 N. Lexington A v e . . Pittsburgh, Po. 15208 ROCKWELL DELTA 10" BAND SAW 10" B A N D SAW SHOWN WITH STAND, MOTOR AND SWITCH ROD INTRODUCTION Your new Band Saw will accurately perform all the usual woodworking band saw operations; straight cutting, curve cutting, cutting plastics and light aluminum, etc. In addition, by using the Cat. No. 28-810 Sanding Attachment in place of the blade, you can sand irregu- lar curved work previously cut on the band saw to add that professional finished look to your work.

. READ the instruction manual before . MAKE SURE that blade tension and blade operating your machine. tracking are properly adjusted on 2. IF YOU ARE NOT thoroughly familiar with the operation of Band Saws and Scroll 1 1 . EO:t"h", :zhine before removing scrap Saws, obtain advice from your supervisor, pieces from the table. instructor or other qualified person. 1 2. ALWAYS keep hands and fingers away 3. REMOVE tie, rings, watch and other jewelry, and roll up sleeves. 1 3. :::::.proper blade size and type. 4 ALWAYS wear safety glasses or a 1 4, DO NOT attempt to saw stock that does face shield. 5. MAKE SURE wiring codes and recommended electrical connection instructions are followed and that machine is properly grounded. 6. MAKE all adjustments with the power off. 7. CHECK all adjustments on the scroll saw by rotating the motor by hand before turning power on. 8. LOWER the hold down on the scroll saw so that it presses lightly on the material 9. :;::;":he upper guide on the band saw about lh" above the material being cut. not have a flat surface, unless a suitable support is used. . HOLD material firmly and feed into blade at a moderate speed. 1 6. TURN OFF the machine if the material is to be backed out of an uncompleted cut. 1 7. MAKE "release" cuts before cutting 1 8. 'D":S"C"O"N';E:T machine from power source when making repairs. 1 9. SHUT OFF power and do not leave machine until it has come to a 20 complete stop. . BEFORE LEAVING the machine, make sure the work area is clean.

Remove the protective coating from the machined sur- faces of the band saw. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover all unpainted surfaces with a light film of good machine oil. ASSEMBLING STAND If you purchased the 50-328 Stand, assemble i t as shown in Fig. 2. lvlake sure the lower shelf is fastened to the upper set of bolt holes in the legs as shown. Note the relationship of the holes and slots in both the upper-and lower shelves, as shown in Fig. 2, to make sure the shelves are assembled properly. ASSEMBLING SAW TO STAND Assenibling the saw to the top shelf of the stand using the four holes (A) Fig. 2. The front of the saw will be toward the end of the top shelf marked (B) Fig. 2. ASSEMBLING MOTOR, MOTOR PULLEY AND V-BELT Motors recommended for use with your band saw are the #60-020-1/3 H P motor with a 1/2" shaft, #60-220-1/2" H P motor with a 1/2" shaft and the #62-413-1/3 H P motor with a 5/8" shaft. If you purchased one of these motors, assemble it to the stand as follows: 1. Fasten the motor to the lower shelf using the four slots (C) Fig. 2, with the shaft end of the motor to- ward the end of the shelf marked (D). Fig. 2. 2. Make sure the four rubber washers (A) are po- sitioned between the motor and the shelf as shown in Fig. 3. 3. If you are using a motor with a 1/2" shaft it i s necessary to place the sleeve (6) and key (C) on the motor shaft, as shown in Fig. 3, before assembling motor pulley. 4. Assemble the Cat. No. 41-033 5/8" bore motor pulley (D) to the motor shaft, as shown in Fig. 3. 5. Make sure the motor pulley (D) Fig. 3, i s in align- ment with the band saw pulley and assemble the #49-130 V-belt (E) to the two pulleys. Fig. 3. 3

If you have purchased the #51-334 switch rod, insert the rod (A) through the hole in the bracket (6) and assemble the end of the switch rod to the toggle switch (C) using the cotter pin supplied. Then fasten the bracket (B) to the upper shelf as shown in Fig. 4. Fig. 4. ASSEMBLING RETRACTABLE CASTER ATTACHMENT If you have purchased the #49-363 Retractable Caster Attachment for use on the steel stand, assemble i t to 1 I the stand as follows: F O O T L E V E R E N D - O F S H A F T 1. Before assembling caster set t o stand, determine which side of the stand would be ntost corlvenient for the foot levers. The foot lever end of the shaft has a cam (A) Fig. 5, assembled in place at the factory. 2. The shafts should be fitted across the narrow side of the steel stand. 1 1 3. Assemble the cams ( 6 ) on both shafts (C) at hole Fig. 5 . (D) Fig. 5. Assemble one cam on each shaft. Cams on each shaft must match when assembled, as shown in Fig. 5. 4. Assemble spring washer (A) and caster mount bracket (6) on each shaft, as shown in Fig. 6. / "R';G*w;'"ER / -CASTER BRACKET ( B Fig. 6. L

shaft using the pin supplied. Foot lever i s assembled to each shaft in the same manner, as shown in Fig. 7. 6. Tilt the steel stand by placing a 2 x 4 under i t so that the legs will be off the floor about 2 inches. 1 -FOOT LEVER ( A 1 Fig. 7. 7. Place caster mount bracket (A) Fia. 8. with shaft (B) and foot lever (C), inside and'under-steel stand leg and place flat head machine screw through the holes in I the steel leg and bracket, from the bottom, and fasten in place with washer and nut (D) Fig. 8. Do not tighten nut (D) too securely at this time. 8. Place sDrino washer. fibre washer and caster mount bracket on opposite end. of shaft (B) Fig. 8. Place bracket on inside of steel leg and fasten i n place with flat head machine screw, washer and nut. Now tlghten both nuts securely. 9. This same method of appllcatlon I S to be followed in assembling shaft to o p p ~ s i t e pair of steel legs. NOTE: The fibre washers are to be used as shims. These washers can be placed on the shaft end opposite the foot lever and between the spring washer and I caster mount. Fig. 8. OPERATING ADJUSTMENTS Although your band saw I S checked and adjusted at the factory, i t may have come out of adjustment during translt. To check and adjust the band saw, proceed as follows: ADJUSTING BLADE TENSION 1. Rilove the upper blade guide (A) Fig. 9 to the highest position.. 2. Turn the tension adjusting screw (B) Fig. 9, clockwise to increase or counterclockwise t o decrease blade tension. 3. Proper blade tension i s obtained when the blade has a flex of approximately 114" i n a 6" span. 4. When the band saw i s not in use it i s good practice to release tension to prolong the life of the blade. TRACKING THE BLADE For accurate work and maximum blade life, it i s im- portant that the blade be centered on the upper wheel. When this adjustment has been properly made, the blade will "track". That is, i t will run Steadily in the same line. Before the tracking adjustment i s made, both the upper and lower blade guides must be moved away from the blade. To "track" the blade, proceed as follows: 1. Disconnect the band saw from the power source and make sure the correct blade tension i s applied to the blade. 2. Remove the front guard (C) Fig. 9, and revolve the upper wheel slowly by hand to determine if the blade i s riding in the center of the wheel. 3. If the blade i s not riding in the center of the wheel, loosen locknut (D) Fig. 9, and while turning the wheel by hand, turn the adjusting screw (E) slightly to the left. You will notice that the blade will move to either side of the wheel. Fig. 9. 4. When the blade is on the center of the upper wheel, tighten locknut (D) Fig. 9. 5. Connect the machine to the power source and jog the motor switch on and off to be certain that proper tracking i s Deing maintained. 6. Then make any minor final adjustments that may be necessary at operating speed. 5

GUIDES I - The upper and lower blade guides are adjusted only after the blade i s tensioned and tracking properly. To adjust the guides, proceed as follows: 1. The upper bracket (A) Fig. 10, is held to the under- neath of the guide post by a cap screw. Loosen the cap screw and move the guide bracket (A) in or out until the front edge of the guides (B) are just behind the "gullets" (bottom of saw teeth). 2. The lower bracket (C) Fig. 10, is mounted directly on the base casting by a square head bolt. Loosen the bolt and move the guide bracket (C) in or out until the front edge of the guides (D) are just behind the "gul- lets" (bottom of the saw teeth). 3. The guides (B) and (D) Fig. 10, are held in the guide brackets with set screws (E). Loosen set screws (E) and adjust guides as close as possible to the side of the blade being careful not t o pinch the blade. 4. IMPORTANT: Set both guides simultaneously so as not to deflect blade. ADJUSTING BLADE SUPPORT BEARINGS The support bearings (F) and (G) Fig. 10, prevent the blade from being pushed too far to the back which could damage the set in the saw teeth. The support bearings (F) and (G) should be set about 1/64'' behind the blade, as follows: 1. Loosen thumb screw (H) Fig. 10 and move upper support bearing (F) 1/64" behind the back edge of the blade and t~ghten thumb screw (H). 2. Loosen set screw (J) and move lower support bearing (G) 1/64'' behind the back edge of the blade and tighten set screw (J). * Fig. 10. ADJUSTING UPPER BLADE GUIDE ASSEMBLY The upper blade guide assembly (A) Fig. 11, should always be set as close as possible to the top surface of the material being cut by loosening thumb screw (6) Fig. 11, and moving the guide assembly (A) to the de- sired position. Fig. 1 1

degrees to the left. T o t i l t the table, loosen hand knob (A) Fig. 12, tilt table to desired angle and tighten hand knob (A). A stop screw (C) i s provided to position the table 90 degrees to the blade. Loosen locknut (B) Fig. i2, and turn stop screw (C) in or out so that it contacts the frame when the table i s 9 0 degrees to the blade. If necessary t o t i l t the table a small amount to the left, remove the stop screw (C) and locknut (B) Fig. 12. Fig. 12. BLADES Always use a sharp blade. Keep it free of gum and pitch. Keep the rubber tires free of sawdust, gum and pitch accumulation. Clean frequently with a stiff fiber brush. Narrow blades are used for cutting small circles or curves while the wider blades are best suited for straight cutting such as ripping. Neither this band saw nor the blades are recommended for cutting iron or steel. Due t o the low cost of Rockwell blades i t i s advisable topurchase newblades rather than attempt to have them sharpened. Make sure the blade guides are always adjusted proper- ly as outlined previously. Do not force or twist the blade around a curve or very short radius. Feed the work uniformly allowing the blade to cut - do not feed too fast. Do not apply excessive tension on blades. The tension i s only necessary t o drive the blade without slipping on the wheels. Narrow blades require more tension than wide blades. INSTALLING THE BLADE LUBRICATION 1. Disconnect band saw from power source. 2. Remove front cover of the band saw. The upper oand saw wheel runs on needle bearings. Lubricate occasionally through oiler, reference #44, of parts drawing, using light machine oil. 3. Remove table insert and table alignment screw. The drive shaft runs on bronze bearings. Lubricate occasionally through oiler, reference #64 of parts 4. Release blade tension and remove blade. drawing, using light machine oil. 5. Check new blade t omake sure teeth are pointing in The blade support bearings are prelubricated and d onot the right direction. If not, turn blade inside out. require further lubrication. 6. Place blade on wheels and adjust tracking, tension and guides as previously outlined. The sliding ways of the upper wheel assembly and the trunnions on the table should be oiled cccasionally so 7. Replace insert and table alignment screw. that they operate freely.

If you purchased the 28-810 Sanding Attachment, assem- ble it to your machine, as follows: 1. Remove the four knurled knobs (A) Fig. 13, and washers, and remove the front cover from the band saw. 2. Remove the table insert and table alignment screw. 3. Release blade tension and remove saw blade from the machine. 4. Remove the lower blade guide bracket (B) Fig. 13, from the machine. 5. Loosen screws (C) Fig. 13, and remove upper blade guides (D). 6. Loosen thumb screw (E) Fig. 13 and push back up bearing (F) to the rear position. Fig. 14. 7. Install sanding belt (A) Fig. 14, t o the two wheels. The arrow on the back of the sanding belt indicates the direction of rotation for the belt. 8. Apply light tension and track the belt on the wheels. 9. Assemble the mounting bracket (B) Fig. 14, to the blade guide bracket (C) as shown, and tighten set screw (D). 10. Assemble either the flat platen (E) or the curved platen (F) to themounting bracket ( B ) a s shown i n Fig. 14. 11. Lower the blade guide bracket (C) so that the end of the platen (G) Fig. 14, is just below the table sur- f ace. 12. Place the table insert (H) Fig. 14, in place. 1 13. Replace the table alignment screw and replace the front cover. INSTALLING LAMP ATTACHMENT If you purchased the 40-882 Lamp Attachment, it can be mounted on your band saw after drilling two holes in the back cover, as shown in Fig. 15. Attach the lamp attachment with the two screws which are furnished with the attachment. DRILL 2 HOLES 7 " 37 DIA. EXISTING HOLES SECT/ON --- OF BACK COVER I+" Fig. IS.

We show you how simple these operations are in our publication No. 4705, "GETTING THE 510ST OUT O F YOUR BAND SAW AND SCROLL SAW". Above is only one page from this h o o l ~ It contains hundreds of illustrations, c h a t s and Inany helpful hints.

56 HSS-532 HBS-847 Moulding 57 Cat #5500~ HBS-848 Moulding 58 SP-206 HBS-849 Moulding 960-02-012-1420 Nameplate 59 NCS-35-S SP-2250 #4 x 3/16 Drive Screw 60 SP-205 960-02-01 2-1419 Nameplate SP-2252 #2 x 3/16 Drive Screw 61 HBS-722 SP-1603 1/4 Washer 62 HBS-8014 HBS-844 Handknob 63 HDP-130 426-01-331-0006 Rear Cover, inck 64 SP-!?A86 HBS-847 Moulding 65 HBS-722 HBS-848 Moulding 66 SP-2605 HBS-849 Moulding 67 HBS-8094 960-02-012-0037 Nameplate 68 HBS-7214 SP-2250 #4 x 3/16 Drive Screw 38 SBS-23 901-04-261-4005 5/16-18 x 2 1/2" Tracking Scr. 69 FJ-316 SP-1403 5/16-18 Wing Nut 70 SBS-19 HBS 819 Spacing Collar 71 SP-6711 SP-514 1/4-20 x 3/8 Mach. Scr. 72 LBS-56 SP-1603 1/4 Washer 73 HBS-802-R SP-7533 1/4-20 x 2 1/2" Truss 74 SP-107 Hd. Scr. HBS-832 2 1/4" Spacer 75 SP-1029 HBS-843 1" Spacer 76 SP-306 SP-7531 1/4-20 x 1 1/2" Truss Hd . Scr. HBS-806-R Adjusting Screw 77 LBS-52 HBS-803 Hinge Bracket 78 HSS-807 HBS-808 Pivot Pin 79 SP-1702 SBSQ4 Coil Spring 80 SP-514 SP-1303 5/16-18 Square Nut 81 LBS-52 HBS-805 Guide Plate 82 SP-1702 SP-1270 3/8-24 Hex Jam Nut 83 SP-514 HBS-804 Hinge Bracket 84 HBS-836 HBS-724 Fiber Washer 85 MH-3417-1 SP-1604 5/16" Washer 86 SP-569 SP-607 5/16-18 x 3/4" Cap Scr. 87 HBS-8154 HBS-7204 Upper Wheel., inck 88 SP-7852 SBS-23 Rubber Tire B-108-X Needle Bearing 89 HBS-712 HBS-807 Upper Wheel Shaft 90 SP-2373 HBS-724 Fiber Washer 91 SP-102 SP-1606 7/16 Washer HBS-730 Cap Screw 92 1085921 SP-2486 Oiler 93 HBS-755-S HBS-810 Guide Post 94 SP-101 HBS-826 Blade Guard SP-502 1/4-20 x 1/41. Mach. Scr. 95 SP-1603 1085921 Guide Block 96 SP-1029 HBS-755-S Blade Support Bearing 97 SP-6721 SP-101 1/4"-20 x 1/4" Headless 98 SP-607 set scr. 99 SP-1703 HBS-711 Upper Guide Bracket 100 NCS-33 SP-1603 1/4" Washer 101 SP-1606 SP-612 1/2-20 x 5/8" Cap Scr. 102 SP-3610 SP-1505 1/4-20 x 1/2" Thumb Scr. 103 C a t #I94 HBS-813 Shoulder Stud 104 C a t #I526 LBS-532 Replacement bearings are furnished oversize and must be real Not shown. 11 5/16-18 Thumb %r. Pulley, inch 5/16-18 x 5/16" Hex. SOC Set Scr. Collar, inch 5/16-18 x l/4" Hex. S~C. Set Scr. Fiber Washer Frame, inck Bearings Oiler Fiber Washer Key Drive Shaft Lower Wheel, incl: Rubber Tire 41/64 x 1 1/4 x .I09 Washer 5/8-18 Jam Nut 1/8 x 3/8" Roll Pin Insert Table 3/8-16 x 1/2" Headless Set Scr. 1/4-20 Hex Nut 1/4-20 x 3/4" Sq. Hd. Set Scr. Table Trunnion Half Tilt Index Plate 1/4" Loc kwasher 1/4-20 x 3/8" Mach Scr. Table Trunnion Half 1/4" Lockwasher 1/4-20 x 3/8" Mach. Scr. Trunnion Bracltet Pointer #8-32 x 3/16" Mach Scr- Trunnion Clamp 7/16-14 x 2 1/4" Sq. Hd. Bolt Lower Guide Bracket 1/4-20 x 1 1/4" Bolt 1/4-20 x 3/8 Headless set Scr. Guide Block Blade Support Bearing 1/4-20 x 1/4" Headless Set Scr. 1/4" Lockwasher 174-20 Hex Nut 1/4 x 7/8 Roll Pin 5/16-18 x 3/4 Cap Scr. 5/16" Lockwasher Coil Spring 7/16" Washer Hand Knob 5/32" Allen Wrench 7/16 x 9/16 Box Wrench Blade ned to fit.

CAT. NO. 5 0 - 3 2 8 STEEL STAND CAT. NO. 51-3 SWITCH ROD NOTE: Use this hole for cams Cam and Pin assembled to Shaft at factory CAT N0.49-363 RETRACTABLE CASTERS

Mo7mting Block l/4" Wather #lo-32 x 1/2" Rd. Hd. Mach. Scr. Retaining Clip #lo-32 x 1/4" Rd. Hd. Mach Scr. Curved Platen Flat Platen Insert Lamp Attachment, incl: Cord Mounting Bracket #lo-32 Hex Nut #lo-32 x 112" Rd. Hd. Mach Scr. 1 /4" Loc kwasher 1/4-20 Hex Nut Steel Link Spec. 1/4-20 x 15/16" Carr. Bolt Cover Spacing Sleeve V-Belt Switch Rod, incl: Clamp Assembly Rod 1/6 x 1/2 Cotter Pin Motor Pulley, inck Pulley 5/16-18 x 5/16 Hex Soc. Set Sa. C a t #23-810 LBS-250 SP-1603 SP-559 Cat. #50-328 SP-834 SP-1605 Steel Stand, incl: 5/16-18 x 3/4" Carr. Bolt 3/8 x 7/8 x 1/16 Steel Washer Motor Mount 5/16-18 Hex Nut 3/8 x 7/8 x 1/16" Steel Washer 5/16-18 Hex Nut 5/16-18 x 1 1/4" Hex Hd. Cap Scr. Top Shelf 5/16-24 Hex. Nut 5/16 Int. Tooth Lockwasha Spec. 5/16-24 Hex Hd. Sa. Bottom Shelf Leg Retractable Castas, inck 5/16-18 Hex Nut 5/16" Lockwasher 3/4 x 5/16 x 1/16" Fiber Washer caster ~ o u n t 5/16-18 x 7/8 Flat Hd. Mach Scr. caster Fiber Washer 5/32 x 7/8 Roll Pin Cam Shaft Spring Washer 5/32 x 1" Roll Pin Foot Lever Caster Mount SBS-53 SBS-52 US-261 C a t #40-882 SP-2447 S-6 SP-1203 SP-559 436-02-11 5-0086 SP-1206 SP-1750 MS-62 436-02-115-0083 436-02-066-0019 C a t #49-363 SP-1300 SP-1703 SP-5552 S-1-S S -4 C a t #49-130 C a t #51-334 MS-17-S 434-02-108-5001 SP-2102 C a t #41-033 NCS-5275-B SP-206 BAND SAW BLADES. A11 71 3/4" Long. No. 28-802 3/16'!. 6 teeth per inch. Minimum cutting radius 1/2". No. 28-803 1/4". 6 teeth per inch. Minimum cutting radius 3/4". No. 28-804 3/8". 5 teeth per inch Minimum cutting radius 1".

C A L I F O R N I A NEW YORK LOS ANGELES, 90007 Rockwell Monufocturing Company 2400 South Grand Avenue Phone: 213 749-0386 O A K L A N D , 94601 Rockwell Monufocturing Company 4621 Malot Street P o s t O f f i c e Box 7327 Phone: 415 535-2424 C O L O R A D O OH I0 D E N V E R , 80207 Rockwell Monufocturing Company 4900 Eost 39th Avenue Phone: 303 388-5803 NEW YORK, 10013 Rudolf Boss, Incorporated 175 Lofoyette Street, Cor. Grand Street Phone: 212 C A 6-4000 B U F F A L O , 14204 Korle Sow Company, Incorporated 138-150 Chicago Street, Cor. So. Pork Ave Phone: 716 853-8053 or 853-8054 C I N C I N N A T I , 45203 R o c k w e l l Monufocturing Cornpony 906 Dalton Street Phone: 513 241-2737 GEORGIA P E N N S Y L V A N I A A T L A N T A (Doroville), 30340 3500 M c C o l l P l a c e Phone: 404 458-2263 HAWAII H O N O L U L U , 96819 Rockwell Monufocturing Company 3209 Koopoko Street Phone: 808 872-048 I L L I N O I S CHICAGO, (Melrose Pork), 60160 Rockwell Monufocturing Cornpony 4533 North Avenue Phone: 312 921-2650 MASSACHUSETTS BOSTON, (Allston), 02134 Rockwell Monufoctur~no C o m ~ o n v d~ . , 414 Combrldge Street Phone: 617 782-1700 P H I L A D E L P H I A , 19120 R o c k w e l l Monufocturing Company 4433-37 Whitoker Avenue Phone: 215 455-7907 P I T T S B U R G H , 15208 RockweII Monufocturing Company 400 North Lexington Avenue Phone: 412 241-8400 T E X A S D A L L A S , 75247 RockweII Monufocturing Company 2934 Iron Ridge Street Post O f f i c e Box 47767 Phone: 214 631-1890 WASHINGTON S E A T T L E , 98101 Rockwell Monufocturing Compony 1918 Minor Avenue Phone: 206 622-4576 WISCONSIN MICHIGAN D E T R O I T ( S o u t h f ~ e l d ) , 48075 Rockwell Monufocturing Compony 18650 West Elght M ~ l e Rood Phone: 313 35R-1000 MISSOURI N. KANSAS C I T Y , 641 16 Rockwell Monufocturing Compony 1141 Swift Avenue Phone: 816 221-2070 MILWAUKEE, 53222 Rockwell Monufocturing Compony 10700 West Burleigh Street Phone: 414 774-3650 C A N A D A G U E L P H , O N T A R I O R o c k w e l l Monufocturing Compony of Conodo L i m ~ t e d 40 Wellington Street Post O f f i c e Box 848 Phone: 807 822-2840 Authorized D e l t o P o r t s Distributors stock a complete l i n e of replacement ports. T o save t i m e and shipping cost sand your ports orders t o your nearest distributor and i n most cases they w i l l be f i l l e d and shipped within 48 hours. We d o not f i l l any ports orders d i r e c t from the factory. 14

Rockwell is proud of the quality of the power tools which it sells. The component parts of our tools are inspected at various stages of pro- duction, and each finished tool is subjected to a final inspection before it is placed in its specially designed carton to await shipment. Because of our confidence in our engineered quality, Rockwell agrees to repair or replace any part or parts of Rockwell Power Tools or Rockwell Power Tool Accessories which examination proves to be defective in workmanship or material. In order to take advantage of this guar- antee, the complete portable power tool or accessory, or in the case of machinery, the part must be returned prepaid to the appropriate factory, Rockwell service center, or authorized service station for examination. This guarantee, of course, does not include repair or replacement required because of misuse, abuse, or normal wear and tear. Repairs made by other than our factory, service center, or authorized service station, relieves Rockwell of further liability under this guarantee. THIS GUARANTEE IS MADE EXPRESSLY I N PLACE OF ALL OTHER GUARANTEES OR WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO QUALITY, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE.

15208 426-02-655-0004 DATED IM 2-15-72 28-810 SANDING ATTACHMENT INSTALLING SANDING ATTACHMENT I TO 10" BAND SAW I wr 1. Remove the four knurled knobs (A) Fig. 1 , and washers, and remove the front cover from the band saw. 2. Remove the table insert and table alignment screw. 3. Release blade tension and remove saw blade from the machine. 4. Remove the lower blade guide bracket (B) Fig. 1 , from the machine. 5. Loosen screws (C) Fig. 1 , and remove upper blade guides.(D). 6. Loosen thumb screw (E) Fig. 1 and push back up bearing (F) to the rear position. F:' " /4 Fig. 1 7. Install sanding belt (A) Fig. 2, to the two wheels. The arrow on the back of the sanding belt indicates the direction of rotation for the belt. 8. Apply light tension and track the belt on the wheels. 9. Assemble the mounting bracket (B) Fig. 14, to the blade guide bracket (C) as shown, and tighten set screw (D). .. , 10. Assemble either the flat platen (E) or the curved ,G platen (F) to the mounting bracket (B) as shown in Fig. 2. $ 11. Lowerthe bladegulde bracket (C) so that theend I* of the platen (G) Flg. 2, I S just below the table sur- ., face. -. 12. Place the table Insert (H) Fig. 2, In place. P - 13. Replace the table alignment screw and replace 1 -- the front cover. Fog 2 . 125 LBS-260 Mounting Block 126 SP-1603 1/4" Washer 127 SP-559 #lo-32 x 1/2" Rd. Hd. Sct. 128 SBS-51 Retaining Clip 129 SP-551 #I0032 x 1/4" Rd. Hd. Sct. curved Platen 130 SBS-53 131 SBS-52 Flat Platen 132 LBS-261 Insert 129 ( 2 ) ~ ~ CAT. NO. 28-810 SANDING ATTACHMENT -