Leica Captivate Technical Reference Manual

The symbols used in this manual have the following meanings: Type Description ☞ Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. To use the product in a permitted manner, please refer to the detailed safety directions in the available User Manuals. The CS35 is a Windows based tablet with a Leica Image installed and Leica Captivate field software running. Changing settings in the image respectively in the operating system of the CS35, other than changes recommended by Leica Geosystems, is the responsibility of the user. The proper operation of Leica Captivate cannot be guaranteed anymore after such changes. Any support by Leica Geosystems after such changes is limited and lies rather in the responsibility of the user or the user’s IT department. Changes allowed Changes that might cause issues • Installing software • Loading another, non Leica image • Installing non Leica provided drivers • Loading software which is also using the CLM license management but working on a different version ☞ Bringing the CS35 into an IT infrastructure might change network set- tings automatically and can result in issues of the Leica network set- tings. • Windows is a registered trademark of Microsoft Corporation in the United States and other countries • Bluetooth® is a registered trademark of Bluetooth SIG, Inc. • SD Logo is a trademark of SD-3C, LLC. All other trademarks are the property of their respective owners. • This manual applies to the Leica Captivate software. • This manual covers all instruments using Leica Captivate software. Video tutorials are available on: http://www.leica-geosystems.com/captivate-howto Purchase Symbols ☞ Trademarks Validity of this man- ual 2

headquarters. For a list of regional contacts, please visit http://leica-geosystems.com/contact‑us/sales_support. Name Description/Format CS20 User Manual All instructions required to operate the product to a basic level are con- tained in the User Manual. Provides an overview of the product together with technical data and safety direc- tions. - ü GS10/GS15 User Manual GS14/GS16 User Manual GS18 User Manual GS25 User Manual TS16 User Manual MS60/TS60 User Manual CS20 Quick Guide Provides an overview of the product together with technical data and safety directions. Intended as a quick reference guide. ü ü GS10/GS15 Quick Guide GS14/GS16 Quick Guide GS18 Quick Guide GS25 Quick Guide TS16 Quick Guide MS60/TS60 Quick Guide Name Description/Format Leica Captivate Tech- nical Reference Man- ual Overall comprehensive guide to the product and apps. Included are detailed descriptions of special soft- ware/hardware settings and soft- ware/hardware functions intended for technical specialists. - ü Licence Activation for CS35 Guide to activate the preinstalled licence on the CS35. ü ü Refer to the following resources for all documentation/software: • the Leica USB documentation card • https://myworld.leica-geosystems.com Leica Geosystems Address Book Available documenta- tion 3

*Please read this License Agreement thoroughly before using the Software* PLEASE READ THE FOLLOWING TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT (THE “LICENSE AGREEMENT”) CAREFULLY BEFORE USING THIS PRODUCT (AS DEFINED IN SECTION 1). THE PRODUCT INCLUDES SOFTWARE, WHICH LEICA GEOSYSTEMS WILL LICENSE TO YOU FOR USE ONLY IN THE MAN- NER DETAILED BELOW. YOU MUST NOT INSTALL OR USE THE SOFTWARE UNLESS YOU HAVE READ AND ACCEPTED THE TERMS AND CONDITIONS HEREIN; BY PRO- CEEDING WITH THE INSTALLATION OR THE USE OF THE SOFTWARE OR ANY PART THEREOF, YOU SHALL BE DEEMED TO HAVE AGREED TO ALL THE TERMS AND CONDITIONS OF THE LICENSE, THE WARRANTY, THE LIMITATION OF LIABILITY AND THE OTHER PROVISIONS OF THIS LICENSE AGREEMENT. IN THE EVENT THAT YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT, YOU SHALL NOT BE PERMITTED TO USE THE SOFT- WARE, AND YOU MUST RETURN THE UNUSED SOFTWARE TOGETHER WITH ITS ACCOMPANYING DOCUMENTATION AND THE PURCHASE RECEIPT TO THE DEALER FROM WHOM YOU PURCHASED THE PRODUCT WITHIN TEN (10) DAYS OF PUR- CHASE TO OBTAIN A FULL REFUND OF THE PURCHASE PRICE. THIS SOFTWARE MAY INCLUDE PRODUCT ACTIVATION AND OTHER TECHNOLOGY DESIGNED TO PREVENT UNAUTHORISED USE AND COPYING OR TO PROVIDE TECHNICAL OR SUPPORT SERVICES REMOTELY BY LEICA GEOSYSTEMS OR ITS AUTHORIZED RESELLER. THIS TECHNOLOGY MAY CAUSE YOUR COMPUTER OR DEVICE TO AUTOMATICALLY CONNECT TO THE INTERNET. ADDITIONALLY, ONCE CONNECTED, THE SOFTWARE MAY TRANSMIT YOUR SERIAL NUMBER/LICENSE NUMBER TO LEICA GEOSYSTEMS AND IN DOING SO MAY PREVENT USES OF THE SOFTWARE WHICH ARE NOT PERMITTED; ALSO, THE SOFTWARE MAY TRANSMIT OTHER SUPPORT-RELATED INFORMATION, SUCH AS CONFIGURATIONS, USAGE STATISTICS, OR ALLOW OR PUSH DOWNLOADS OF UPDATES TO PRODUCT SOFT- WARE. 1 Definitions “Patches” shall mean the fixing of a programming error (bug) or a wrong behaviour of the software or the related software code. “Product” shall mean (a) the Leica Geosystems instrument you have pur- chased for use with the Software, if any, or (b) the Software itself, if you have purchased the Software on a stand-alone basis. “Purchase Agreement” shall mean the purchase order, agreement or other document pursuant to which you purchased the Product. “Software” shall, depending on the case, mean the Leica Geosystems soft- ware and the related documentation (in electronic or in paper form) (a) that is supplied to you on a data carrier medium, or (b) that is pre-installed on the Product (if the Product is not the Software itself), or (c) that can be downloa- ded by you online pursuant to prior authorization from Leica Geosystems. “Specifications” shall mean the functionality of the Software as described in the Product description and the help functions, if any, provided in electronic or in paper form by Leica Geosystems in conjunction with the Software. 4 Leica Geosystems Software Licence Agreement

ment defined in the Product description that is required for the proper func- tioning of the Software. “Updates” shall mean software that correct faults in the Software or that, pur- suant to no obligation hereunder, enhances the functionality of the Software by providing additional functions or any other increases in performance. 2 Scope of the License Leica Geosystems AG, Heinrich-Wild-Strasse, CH-9435 Heerbrugg, Switzer- land (alternatively, the "Licensor" or “Leica Geosystems”) hereby grants to you (the "Licensee") subject to payment of the applicable license fee and to contin- uous compliance with all the provisions hereinafter, the non-exclusive, non- transferable, non-sublicenseable and non-assignable right, to use in the manner set forth herein the Software on one (1) application, unless other- wise agreed upon in the Purchase Agreement. The use of the Software for a purpose other than as licensed herein shall not be permitted. The foregoing license is limited as follows: (a) the Software will only be used on such permitted number of applications and in a mechanically readable form; (b) the Software will as a whole or in part be installed, saved and run only on the Specified Computer Facility in accordance with the installation instructions of Licensor; and (c) one (1) copy of the Software may be made exclusively for security and archiving purposes, provided that such copy carries a comprehen- sive copyright notice together with all additional references to the rights of Licensor to the Software and the designation of the original version. In the event that the Software is an update or an additional module for an already licensed system, instrument or facility, Licensee may make only as many copies as previously authorized by Licensor. Certain Software supplied by Licensor may contain a special program that regulates and monitors the number of simulta- neous users of the Software in a network environment together with the num- ber of the licensed copies of the Software, excluding back-up copies (the “Special Program”). Licensee hereby consents to the inclusion and operation of such Special Program and to the use of other security devices in connection with the Software and Licensee shall be prohibited from circumventing, reverse-engineering or copying such Special Program or any other security devices. Licensee will only use the Software in the manner permitted under the forego- ing license and will not (a) alter the Software or any part thereof in any man- ner (including, without limitation, through modifications, adaptations, transla- tions, or second-hand versions.), (b) decompile the Software or any part thereof, (c) reverse-engineer or disassemble the Software or any part thereof or manipulate the Software in any other way into a form that persons can read, (d) transfer the Software or any part thereof to another operating sys- tem, (e) pass on the Software or any part thereof to a third party or make it available to a third party in any other manner (including, without limitation, for testing or by gift, lease, loan or sublicense, or via a service bureau) without the prior written consent of Licensor, (f) use the Software or any part thereof on a computer facility other than the Specified Computer Facility, or on more than one work station, on networks, on a client server system or on mobile addi- tional instruments without the prior written consent of Licensor, (g) remove, alter, or obscure any proprietary notices, labels, or marks from the Software, (h) use any equipment, device, software, or other means designed to circum- vent or remove any form of copy protection used by Leica Geosystems in con- nection with the Software, or use the Software together with any authorization code, serial number, or other copy-protection device not supplied by Leica Geo- Leica Geosystems Software Licence Agreement 5

device, software, or other means designed to circumvent or remove any usage restrictions, or to enable functionality disabled by Leica Geosystems. Installation, access, and continued use of the Software may require an entitle- ment number. Registration may be required for certain features or before an entitlement number is issued by Leica Geosystems. Licensee agrees that Leica Geosystems may use data and information provided by Licensee, an authorized reseller, or any other third party acting on behalf of Licensee in connection with the purchase of the software license to register the Software. Licensee agrees to provide Leica Geosystems, an authorized reseller, or any other third party acting on Licensee’s behalf with accurate and current registration infor- mation, and Licensee further agrees to maintain and update this registration information through customer data registration processes that may be provi- ded by Leica Geosystems. By installing and using the Software, Licensee con- sents to Leica Geosystems using any personal information provided at registra- tion, or updated thereafter, to issue entitlement numbers, to manage Leica Geosystems’s relationship with Licensee (including automating the issuance of entitlement numbers for future purchases), and to otherwise use any such per- sonal information in conformance with its privacy policy –if applicable-, which is available on request. The activation security mechanisms may disable the Software if Licensee attempts without Leica Geosystems’ consent or authorisation to transfer it to another computer or device, if the date-setting mechanisms on the computer or devise is tampered with, if Licensee uses the Software past an applicable evaluation period or limited term, or if Licensee undertakes certain other actions that may offset the security mode. This Software may cause the Specified Computer Facility to automatically con- nect to the Internet and to communicate with Leica Geosystems and or with third parties connected with the development and/or the validation of the Software. This Software license does not cover or include the use of third party soft- ware. Licensee’s right to use any such software shall be governed by the provi- sions set forth by such third party. This Software license shall also apply to Open Source Software (OSS). In case of conflict with the terms of this Software License Agreement, the terms of the respective OSS license agreement shall govern. 3 Warranty Express Warranty. Licensor warrants to the original Licensee that (a) the data carrier medium on which the Software is stored shall be free from defects in workmanship and material at the time of delivery to Licensee, and (b) for the warranty period specified in the relevant Purchase Order, the Soft- ware (but not Updates) shall function in material accordance with the Specifi- cations, provided the Software is used in the manner permitted in the forego- ing license, on the Specified Computer Facility and in accordance with the con- ditions of installation, use and operation set forth in the Product description. Licensor does not warrant that the Software will be free of defects, run without interruption, meet the expectations of Licensee, or function in combi- nation with the hardware or software products of third parties, or that all pro- gram errors will be corrected. In addition to the foregoing, in order for a defect in the Software to be sufficiently material so as to violate the warranty set forth in letter (b) above of this paragraph, the defect must cause the Software - while being used in the manner permitted in the foregoing license - to func- 6 Leica Geosystems Software Licence Agreement

purpose described in the Product description. Furthermore, if the required functionality can be achieved by the Licensee indirectly (through a so called “work-around”), then the applicable impairment shall not constitute a defect giving rise to duties under the foregoing warranty. Licensor’s sole obligation under the foregoing warranty shall be, at Licensor’s sole option and expense, to either (a) replace the data carrier and/or the Software, so as to materially conform with the Specifications (including, without limitation, replacement with a more recent version or equivalent software); or (b) repair the Software by providing, correction codes, work-around solutions and/or Updates, includ- ing updated documentation and other documents; or (c) terminate this License Agreement and refund all license fees received following the return of the Software in accordance with Section 7 below. The foregoing warranty will apply to any replaced data carriers and Software until expiry of the original warranty period. The costs and risk of any delivery of Software to the service point nominated by Licensor shall be borne by Licensee. Obtaining warranty service. If Licensee detects a defect in the Software that may give rise to a duty under the foregoing warranty, it will cease using the Software immediately and notify Licensor or its local sales partner in writing of the defect and provide sufficient supporting documentation within the period for notifying defects. Such period for notifying defects is ninety (90) days from the date of delivery of the data carrier medium (for a defect in the data carrier medium) and one (1) year from the date of delivery of the Software (for a defect in the Software). The written supporting documentation relating to the defect will be sufficient if it permits the defect detected by Licensee to be capable of reproduction by Licensor. Licensee will annex the relevant purchase receipt so that Licensor can determine compliance with the periods for notify- ing defects. Licensee will not carry out modifications or repairs itself or permit such modifications or repairs to be carried out by unauthorized third parties. If requested by Licensor, Licensee will support Licensor in the analysis of the cau- ses and conditions giving rise to the defect, as well as in the development and testing of correction codes or a work-around solution. Warranty exclusive. Licensee’s sole remedy for Software defects is set forth in the foregoing express warranty. The Software is licensed with its current fea- tures “as is” and with no warranty or guarantee of whatever nature, other than the foregoing express warranty. Such express warranty is in lieu of all other warranties, express or implied, either in fact or by operation of law, statutory or otherwise, including warranties, terms or conditions of merchantability, fit- ness for a particular purpose, satisfactory quality and non-infringement, all of which are expressly disclaimed. Licensee acknowledges that Licensor’s sales partner or dealers are not allowed to provide any warranty, guarantee or assur- ance with regard to the use, suitability, or results of use of the Software, or with regard to the precision, accuracy or reliability thereof, and any such war- ranty, guarantee or assurance is of no effect. It shall be the responsibility of Licensee to select the Software that fulfils its requirements. Licensee shall bear the full risk for the performance of and results achieved by the Software and for its suitability for the use that Licensee has planned for it, even when Licen- sor has been informed of the planned use of the Software. Licensor shall be relieved of its obligations under the foregoing express warranty to the extent that any defect is caused by circumstances for which it is not responsible, including, without limitation, (a) non-compliance with the conditions of use and operation contained in the Product description or the documentation; (b) non-compliance with the provisions of this License Agree- ment; (c) unauthorized modifications to or interference with the Software by Licensee or third parties; (d) errors in the operation of the Software by Licen- Leica Geosystems Software Licence Agreement 7

not been supplied by Licensor; or (f) use on a computer facility other than the Specified Computer Facility. In the event that Licensor is not responsible for a defect pursuant to these warranty provisions or that Licensor incurs additional expenditure as a result of the failure of Licensee to comply fully with its obligations under this Section 3 (including, without limitation, its obligation to support and provide documenta- tion to Licensor), Licensor shall have the right to charge Licensee for the costs that it incurs for the analysis and rectification of the defect according to the time and materials required and in accordance with the applicable rates charged by Licensor at the time. 4 Intellectual Property Rights Licensee shall only hold those rights to the Software that are expressly descri- bed in Section 2 of this License Agreement. Any other rights with regard to the Software, including without limitation, ownership rights and patent, copy- right, trademark, trade secret and other intellectual property rights, shall remain the sole property of Licensor. Licensee will not remove from the Software any references to copyrights, trademarks or other ownership rights, or cover up or alter any such references. Licensee will take all reasonable steps to prevent any unauthorized use, reproduction, sale, or publication of the Soft- ware or the unauthorized provision of access thereto. Licensee will indemnify and hold harmless Licensor from any losses, damages, claims and expenses (including, without limitation, reasonable legal expenses) relating to any infringement of the rights of Licensor caused by Licensee, Licensee’s breach of this License Agreement or Licensee’s use of the Software in a manner not authorized under this license agreement. In the event that Licensee faces legal proceedings based on the allegation that Licensee’s use of a valid, unmodified version of the Software in accord- ance with the terms and conditions of this License Agreement infringes an existing intellectual property right in Switzerland, the European Union, Japan, the USA or in any other countries where Licensor sells the Software, or that such use constitutes unfair competition, Licensor shall defend any such pro- ceedings at its own expense, provided that Licensee has informed Licensor immediately in writing of the proceedings raised, has granted Licensor a Power of Attorney authorizing it to conduct and settle the legal proceedings, and, if requested by Licensor, has provided Licensor with reasonable support in the defence of such proceedings. In the event that, in the sole opinion of Licensor, the valid, unmodified ver- sion of the Software could infringe the intellectual property rights of third parties, it shall at its own exclusive discretion (a) either obtain authori- zation from such third party for the continued use of the Software by Licensee, (b) replace the Software, (c) modify it in such a manner that there is no longer any infringement of intellectual property rights, or (d) if the foregoing meas- ures are not within the bounds of what is reasonably possible, terminate this Agreement effective immediately and refund to Licensee a portion of the license fees paid (after deduction of an appropriate payment for the use already made of the Software by Licensee). Notwithstanding the foregoing, Licensor shall be relieved of its obligations under the prior two paragraphs of this Section 4 if the infringement claim is based on the allegation or fact that the Software (a) has been modified by Licensee, or (b) is being used with other programs or data and such combina- tion has led to an infringement of a third party right, (c) has been used on a computer facility other than the Specified Computer Facility, or (d) has been 8 Leica Geosystems Software Licence Agreement

description. 5 Limitation of Liability To the extent permitted under applicable law, Licensor shall not be liable for any direct, indirect or consequential loss or damage, including, without limita- tion, loss of income, loss of business profits or loss of contracts, unrealized cost reductions, loss of data, business interruption, or increased costs on the part of Licensee or any other financial losses, that result from or in connection with the purchase, license, use, breakdown or interruption of operation of the Software. The foregoing limitation of liability shall also apply in the event that Licensor has been notified of the possibility of such losses being incurred. Licensor shall only be liable for loss or damage caused by Licensor’s gross neg- ligence or wilful misconduct. This limitation of liability shall apply to all claims for loss and damage irrespective of their legal grounds, including, without limi- tation, claims based on tort, contract, pre- contract or quasi-contract. This limi- tation of liability shall also apply to any officers, directors or employees of Licensor, or any representatives or agents of Licensor that are involved in the development, marketing or supply of the Software. It shall be the exclusive duty of Licensee to ensure that it and its staff pos- sesses the required knowledge to properly install and use the Software. Licen- sor shall not be liable for problems and defects that arise from insufficient knowledge on the part of the users of the Software. 6 Exclusion of other Assurances Licensee hereby agrees that no verbal or written assurances, declarations, statements, recommendations or advertising messages have been made by Licensor, its employees, sales partners, agents, dealers or downstream distrib- utors that could give rise to an amendment or extension of the foregoing war- ranties and limitation of liability. Licensee is hereby given notice that none of the forenamed persons is authorized by Licensor to make any such amend- ments or to provide any such assurances. 7 Duration and Termination This License Agreement shall come into force on the agreement of Licensee to the provisions hereof and shall remain in force for the term indicated in the Purchase Order. In addition to any other right of termination provided in this License Agree- ment, each party shall be entitled to terminate this License Agreement at any time with immediate effect: a) in the event of a material violation of a contractual duty by the other party, including, without limitation, default in payment of the license fee, if the party in breach does not remedy such violation within forty-five (45) days after being served with a notice in writing; b) is unable to pay its debts, or becomes insolvent, or is subject to an order or a resolution for its liquidation, administration, winding-up or dissolution (otherwise than for the purposes of a solvent amalgamation or reconstruc- tion), or has an administrative or other receiver, manager, trustee, liquida- tor, administrator or similar officer appointed over all or any substantial part of its assets, or enters into or proposes any composition or arrange- ment with its creditors generally, or is subject to any analogous event or proceeding in any applicable jurisdiction. Leica Geosystems Software Licence Agreement 9

held by Licensee shall expire. Within thirty (30) days from the date of termina- tion of the License Agreement Licensee will return to Licensor or destroy (and confirm such destruction in writing to Licensor) the Software and all copies or partial copies thereof that have been made, as well as all modified parts of the Software or interfacing parts linking to other programs or data systems, and to the extent available, all security devices. 8 Import, Export and Use of the Software Licensee shall be exclusively responsible for ensuring compliance with the rele- vant legislation relating to its rights to import, export or use the Software. 9 General Provisions If any term or provision of this agreement shall be or shall become invalid or unenforceable for any reason, such term or provision shall be ineffective to the extent of such invalidity or unenforceability without invalidating the remaining terms and provisions hereof, provided, however, that the parties shall replace any such invalid or unenforceable provision by a valid and enforceable provision as comes nearest to the original provision in economic impact and intent. This agreement may only be modified in writing, signed by an authorized officer of Leica Geosystems. This is the entire agreement between Leica Geosystems and Licensee regarding the Software and it supersedes any prior representation, discussions, undertakings, communications or advertising relating to the Soft- ware. 10 Third Party Beneficiary The parties expressly agree that subsidiaries of Leica Geosystems, including the entity from whom the Customer purchased the Product, is a third party beneficiary of this Software License Agreement, and, without limiting the fore- going, such subsidiaries shall have all defences available to Leica Geosystems under this Software License Agreement. 11 Governing Law and Place of Jurisdiction This Agreement shall be governed by the laws of Switzerland, excluding all con- flicts of laws principles and excluding the United Nations Convention on Con- tracts for the International Sale of Goods. The ordinary courts at the headquar- ters of Leica Geosystems AG in Balgach, Switzerland shall have jurisdiction. Licensor shall, in its sole discretion, also have the right to invoke the courts of law having jurisdiction at the domicile or place of business of Licensee. Leica Geosystems AG Heinrich-Wild-Strasse 201 CH - 9435 Heerbrugg (Switzerland) Heerbrugg, 25 March 2013 10 Leica Geosystems Software Licence Agreement

with supplied stylus. The workflow is the same for keyboard and touch screen entry, the only difference lies in the way information is selected and entered. Operation by keyboard Information is selected and entered using the keys. Operation by touch screen Information is selected and entered on the screen using the supplied stylus. Operation Description To select an item Tap on the item. To start the edit mode in editable fields Tap on the editable field. To highlight an item or parts of it for editing Drag the supplied stylus from the left to the right. To accept data entered into an edita- ble field and exit the edit mode Tap on the screen outside of the editable field. To open a context-sensitive menu Tap on the item and hold for 2 s. Searching is possible in panels with and without pages. 1. Open a panel or page with listed items. 2. Type in any letter or number key to start the search. ☞ On the TS, the setting for Data input method in Screen, Audio & Text Input defines how characters can be typed. Refer to "28.2 Screen, audio & text input". A search field appears below the icons in the top right area of the panel. The field shows the characters typed in. ☞ The job search is not case sensitive. 3. The item with the name closest to the letters typed in is highlighted. Keyboard and Touch Screen Searching Operating Principles 11

Home menu Key Function Function keys F1-F6 Press Esc first to leave the job search. Correspond to six softkeys that appear on the bottom of the screen when the screen is activa- ted. Function keys F7-F12 Press Esc first to leave the job search. User definable keys to execute chosen com- mands or access chosen screens. Alphanumeric keys To type letters and numbers. Esc Leaves the job search. Fn Press Esc first to leave the job search. Switches between the first and second level of function keys. Enter Leaves the job search. ON/OFF Turns to Power Options menu when held for 2 s. Favourites Without function. The search field remains in edit mode. Home Leaves the job search. OK Leaves the job search. Functions of icons when job search is active in the Leica Captivate - Home menu Icon Function Magnifying glass Leaves the job search. Functions in job and apps carousel when job search is active in the Leica Captivate - Home menu Action Function Tapping on any job that is not in the centre of the job carousel Leaves the job search. Moves the tapped job to the centre of the carou- sel. 12 Operating Principles

is in the centre of the job carousel Leaves the job search. Opens the job menu for that job. Tapping on any app in apps carousel Leaves the job search. ☞ Tap again on the app icon to start the app. 2.2 Configurable Keys 2.2.1 Hot Keys Two levels of hot keys exist: • The first level is the keys F7 to F12 and F13, the key on the side of the instrument. • The second level is the combination of Fn and F7 to F12. Hot keys provide a shortcut for quickly and directly carrying out functions assigned to the keys. The assignment of functions to hot keys is user configu- rable. • The first level is accessed by pressing F7 ... F12 or F13 directly. • The second level is accessed by pressing Fn first followed by F7 ... F12. • Hot keys can be pressed at any time. It is possible that a function assigned to a hot key cannot be used in certain situations. This step-by-step description shows how to assign the Regional panel to the F7 key. 1. Select Leica Captivate - Home: Settings\Customisation\Hot keys & favourites. 2. Hot Keys & Favourites Select F7: User - Regional settings on the TS hot keys page. 3. OK 4. OK 5. Press F7 to access Regional. The key on the side of the instrument is located next to the right-hand fine drives. It enables fast and comfortable recording of measurements. Being equipped with a soft touch key located on the instrument’s turning axis allows highest precision measurements. All functions that can be assigned to the hot keys can be assigned to this key including . 2.2.2 Favourites Key For GS: • The key opens the My GS Favourites menu. For TS: • The key opens the My TS Favourites menu. Description Functionality Use Define hot key step- by-step Key on the side of the instrument Description Operating Principles 13

contain the most used functions. The favourites menu cannot be accessed while in a settings panel. Selecting an option in the menu carries out the function assigned to the option. The following panel is an example of what a My GS Favourites or My TS Favourites menu can look like. The functions which are assigned to the indi- vidual places in the menu can differ depending on the settings. Tap on a pop-up bubble menu item to use a function. Defining the favourites menu is the same process as for defining the hot keys. Refer to "2.2.1 Hot Keys". Functionality of the favourites menu My favourites menu Define favourites menu step-by-step 14 Operating Principles

Jobs To access the Job Management panel. Refer to "3.3 Job Management". Fn Instru- ment To switch between GS and TS mode. Fn New job To create a new job. Fn Exit To close software. Icon Description Displayed in the bottom right corner of the job tile. When the icon is displayed, then the job is stored to the SD card. When no icon is displayed, then the job is stored to the internal memory. Software maintenance is close to due date or has expired. The reminder message has previously been confirmed with OK. The icon will disappear when licence keys are entered manually or uploaded from a file. Refer to "29.3 Load licence keys". Displayed in the bottom right corner of the Settings tile. When the icon is displayed, a new Leica Captivate version is available in myWorld. For an automatic check, the instrument must be connected to the Internet. When no icon is displayed, there is no new version or the instrument is not connected to the Internet. Description of the functions Function Description Icon bar • For status information and frequently used functionality. Leica Captivate - Home Home 15

• Tap to select an existing job. • Typing one or several letters of a job name moves the job with the most similar name to the centre of the car- ousel. If no job name starts with the typed letters, the active job stays active. • Select the left or right most tile in the carousel: Press Fn. Then press Home or End. • Tap to create a job. Job carousel • To manage jobs and data, import and export data, send data and delete jobs. • Job menu items are shown on the second level of each job. Click a job to see the menu items. • To delete a job, move the job in the centre of the job carousel. Press the key on the keyboard. Apps carou- sel Settings • To access settings regarding the instrument, instrument connections, the software and the display as well as other useful tools. Apps • Contains all loaded apps. To select and start an app. • Selecting an option in the menu starts the app. Settings and measurements that can be performed depend on the app. 3.2 Job Menu The job menu is available when operating an RTK rover or a TS. It is used to: • View and edit job properties. • Export and copy data. • Create, view and edit data. • Start Leica Exchange. • Import data. • Delete a job. Next step View & edit job properties Refer to chapter "6 Job Menu - Jobs". View & edit data Refer to chapter "7 Job Menu - View & edit data". Description Job menu 16 Home

Import data". Export data Refer to chapter "11 Job Menu - Export data". Send data To start an online service that allows the data exchange between two users of the service. Delete To delete the current job. ☞ To delete a job, move the job in the centre of the job carousel. Press the key on the key- board. 3.3 Job Management Listed are the existing jobs on the data storage devices. Key Description OK To accept the settings and to return to the previous panel. New To create a new job. Edit To edit the highlighted job. Delete To delete the highlighted job. Data To view, edit and delete points, lines, images and scans stored with the job. Points, lines, images and scans are shown on separate pages. Selected sort and filter settings apply. All To set all jobs in the job carousel visible or invisible. Description of symbols The symbols match the setting for Display in job carousel in Job properties, General page. Refer to "6.4 Editing a Job". Symbol Description The job is visible in the job carousel. Job Management Home 17

3.4 Settings Settings is used to: • Configure parameters related to the interfaces. • Configure parameters related to the instrument. • Configure user favourite settings for the survey and the instrument. • Configure parameters which are not directly related to surveying data, such as loading firmware or licence keys and format data storage devices. Key Description OK To select the highlighted option and to continue with the subsequent panel. Fn Instru- ment To switch between GS and TS mode. Next step Connections Refer to chapter "18 Connections - All other connections". TS instrument Refer to chapter "22 Settings - TS instrument". GS Sensor Refer to chapter "23 Settings - GS Sensor". Point storage Refer to chapter "25 Settings - Point storage". Customisation Refer to chapter "26 Settings - Cus- tomisation". System Refer to "28 Settings - System". Tools Refer to chapter "29 Settings - Tools". About Leica Captivate Refer to "30 Settings -About Leica Captivate". Description Settings 18 Home

The icons provide information related to basic instrument functions. The icons that appear depend upon which instrument is used and the current instrument configuration. 008291_002 a b c d e f g h a Aim & Search b Measure & Target c Instrument d Current horizontal angle of instrument, tap to see the target height e Current vertical angle of instrument, tap to see the slope distance f Connections g Battery h Time 008292_001 a b c d e f g h a GS Position b Satellite Tracking c RTK Data Link d 2D position quality, tap to see the antenna height e 1D position quality, tap to see the 3D position quality f Connections g Battery h Time Displays the current automatic aiming or PowerSearch settings. Icon Description The instrument is in auto aiming mode using automatic aiming. The instrument is in manual aiming mode The instrument is in target lock mode, however not currently fol- lowing a prism. Lock Status: Unlocked. Description ☞ Icon bar - TS Mode Icon bar - GNSS Mode Aim & Search Icons 19

prism. Lock Status: Locked. The instrument is in prediction or locking on the fly is activated. The instrument locks toward a prism coming into the field of view and follows this prism. Searching for the prism using Auto aiming. Searching for the prism using PowerSearch. Caution. Connection between CS and TS is not established. Displays the selected measurement mode. Displays the selected prism. The laser icon is displayed when the red laser is active. Icon Description Measure distance: Once Measure distance: Once & fast Measure distance: Continuously Measure & Target 20 Icons

Measure distance: Greater than 4km Measure distance: >4km & average Measure distance: Highest precision on TS60 Leica round prism Leica 360° prism Leica mini prism Leica mini 0 Icons 21

Leica Machine Automation power prism MPR122 Leica reflective tape or HDS target. Any surface User-defined prism Distance measurement active Red laser is turned on Red laser is turned off 22 Icons

or II icon. Icon Description Compensator is turned off. Compensator is turned on, but is out of range. The current face of the instrument is shown, if the compensator and the horizontal correction are turned on. Displays the status of the current position. As soon as this icon becomes visi- ble the instrument is in a stage where practical operation can commence. Icon Description Navigation position available Navigation position available Tilt compensation active ☞ When the tilt pole initialisation is lost, move the pole naturally for a new initialisation. Code solution available Code solution available Tilt compensation active ☞ When the tilt pole initialisation is lost, move the pole naturally for a new initialisation. Fixed position available Fixed position available Tilt compensation active ☞ When the tilt pole initialisation is lost, move the pole naturally for a new initialisation. Level status GS Position Icons 23

xRTK fixed position available Tilt compensation active ☞ When the tilt pole initialisation is lost, move the pole naturally for a new initialisation. The checks indicate that an ambiguity check is being made. Displays the number of theoretically visible satellites above the configured cut- off angle according to the current almanac. Icon Description The number of visible satellites. Displays the status of the real-time device configured to be used. Icon Description An arrow pointing down indicates a real-time rover. The arrow flashes when real-time messages are received. An arrow pointing up indicates a real-time base. The arrow flashes when real-time messages are sent. Sending/receiving data Signal strength Displayed if the device being used for the RTK rover interface is the internal CS20 modem. RTK using Internet Phone Radio RS232 Satellite Tracking RTK Data Link 24 Icons

Internet not connected. Logged in to Leica Exchange. Data upload in progress. Data download in progress. Exchanging new data. Data transfer problem. Active Assist is active. Leica technical support can gain remote access to the instrument. Displays the battery level. Icon Description Sufficient power available. Connections Battery Icons 25

Power level is getting very low. Battery empty. Instrument turns off immediately. 26 Icons

5.1 Access Status information helps using the instrument by showing the state of many instrument functions. All fields are display only fields. Unavailable information is indicated by -----. Frequently used functionality can be accessed and changed quickly. The change is applied immediately. The workflow is not interrupted. Changes are stored in the active working style. Tap an icon in the icon area. An icon pop-up bubble opens. An icon pop-up bubble shows: • Status information • Functionality related to the icon which was tapped Tap a bubble icon to use the functionality. To close an icon pop-up bubble: • Press any key on the keypad. • Touch the panel anywhere outside of the icon pop-up bubble. 009331_001_en a b c a Icon in icon area b Status information c Bubble icon Refer to the individual chapters for more information. Aim & Search Status Information Functionality • Current target aiming • PowerSearch filter • Switch between manual/auto- matic aiming • Turn target lock on/off • Locks onto a prism by searching or by waiting for a prism to come into the field of view • Switch between PowerSearch left/right Description Access Description of the icon pop-up bubbles Icon Pop-up Bubbles 27

Status Information Functionality • Current target with defined con- stants • Type of distance measurement • Switch between measurements to any surface or to prisms • Set continuous or non-continu- ous measurement mode • Select targets • Turn the red laser of the reflec- torless EDM on/off Instrument Status Information Functionality • Current setup ID, instrument height and level status • Change the face of the telescope • Turn the telescope to a certain direction • Electronic level bubble and com- pensator settings • Turn the instrument using key- board arrow keys • Information related to the cur- rent setup on the instrument Hz and V Status Information Functionality • Current horizontal and vertical angle • Tap to see pole height • Current horizontal and vertical angle • Tap to see pole height and slope distance - GS Position Status Information Functionality • Current GNSS position • Information related to the cur- rent antenna position and the speed of the antenna. Satellite Tracking Status Information Functionality • Number of satellites available and satellites used per satellite systemG (GPS), R (GLONASS), E (Galileo) or B (BeiDou) • Satellites ordered by the eleva- tion angle, satellite information in a graphical way, used almanac • Information related to logging of raw observations. 28 Icon Pop-up Bubbles

Status Information Functionality • Seconds since last RTK message was sent/received • Percentage of real-time data received from the base compared with data received from the antenna within the last minute • Load an existing RTK profile using the RTK rover wizard. • Information related to real-time data, for example the data link and the device used to transfer real-time data • Status Internet connection • Force a new initialisation • Change the radio channel 2D and 1D Status Information Functionality • Current 2D coordinate quality of computed position - • Current height coordinate quality of computed position • Tap to see pole height • Tap to see 3D position quality Connections Status Information Functionality • Internet online or not • Status Bluetooth connection • Start Leica Exchange • Start Start Active Assist Battery and time Status Information Functionality • Date and time • Remaining power capacity for the battery • Active memory • Select instruments to use • Return to Leica Captivate - Home menu • Start online help • Usage and status of battery and memory • Begin the camera function • Create a sketch on a virtual piece of paper 5.2 Icon Pop-Up Bubble: Aim & Search 5.2.1 Bubble Icons Icon Description Auto aiming Sets Aim at target: Automatic. Manual aiming Sets Aim at target: Manually. Available for Aim at target: With lock. For robotic instruments and the remote operation with CS20. Bubble icons Icon Pop-up Bubbles 29

Searches for a prism to lock on. Wait & lock Locks to a prism as soon as it enters the field of view of automatic aiming. When previously locked to a prism and target lock was lost. Works on all prisms and tape targets. ☞ A PowerSearch helps to lock to shaking prisms. Target lock off Stops the lock. Target lock on Sets Aim at target: With lock. Target lock off Sets Aim at target to the previous non-lock setting. Filter learn Starts a PowerSearch scan by doing three times a 360° scan with different vertical positions of the telescope. The PowerSearch scan finds prisms and other reflec- tive spots in the surrounding of the instrument. Around each found prism or reflective spot, an exclu- sion area is defined. The exclusion area has the dimension of Hz = ± 1 gon, V = ± 50 gon and d = ± 12 m is defined. Filter on Available when Filter learn was used before. Turns on the PowerSearch filter and excludes the learned prisms from a PowerSearch. Filter off Available when Filter learn was used before. Turns off the PowerSearch filter and includes all prisms in a PowerSearch. PowerSearch Prisms are searched for with PowerSearch in the PowerSearch window when this icon is used. ☞ If this icon is selected and Meas any sur- face is still set, then this setting is changed to Measure prism. 5.3 Icon Pop-Up Bubble: Measure & Target Icon Description Meas any surface To measure to any surface (reflectorless). Automati- cally sets Aim at target: Manually. Measure prism To measure to prisms. Meas continuous To set the distance measurements to continuous. Meas single shot To set the distance measurements to the previous non-continuous mode. Targets To select a prism. Red laser on To turn the red laser of the reflectorless EDM on. Red laser off To turn the red laser of the reflectorless EDM off. Bubble icons 30 Icon Pop-up Bubbles

5.4.1 Bubble Icons Icon Description Current setup Information related to the current setup on the instrument. Refer to "5.4.2 Current setup". Turn to Hz/V To turn the instrument to a specific entered position. Refer to "5.4.3 Turn to Hz/V". Arrow keys To turn the instrument using the arrow keys. Refer to "5.4.4 Arrow keys". 5.4.2 Current setup Key Description OK To exit the panel. ppm/Scale fctr To switch between displaying the setup scale factor and the setup ppm. Description of fields Field Description Current setup ID The current setup. Instrument height Instrument height of the current setup. Setup method The setup method used for the current setup. Easting Easting value of the instrument position. Northing Northing value of the instrument position. Local ellipsoid height or Height For a selected coordinate system, ellipsoidal height and elevation can be displayed. Temperature Temperature set on the instrument. Pressure Pressure set on the instrument. Atmospheric ppm Atmospheric ppm set on the instrument. Setup ppm Ppm of the current setup. Setup scale Scale factor of the current setup. Bubble icons TS Current Setup Info Icon Pop-up Bubbles 31

This panel is used when the instrument is controlled remotely and when the telescope must be turned to a certain direction. Key Description OK To return to Leica Captivate - Home menu. The instrument turns to the prism. Page To change to another page on this panel. Description of fields Field Option Description Azimuth Editable field Oriented horizontal direction for the instru- ment to turn to. Angle right Editable field Horizontal angle from the backsight point for the instrument to turn to. Available when Hz angle display: North azimuth is set in Regional, Angle page. V angle Editable field Vertical direction for the instrument to turn to. Next step Page changes to the Relative page. The values are added to the current telescope position to calculate the new direction for the telescope to turn to. Description of fields Field Option Description Difference in Hz angle Editable field Angular difference for the horizontal angle to turn to. Difference in V angle Editable field Angular difference for the vertical angle to turn to. Next step Press OK. The instrument turns to the prism. Description Turn Instrument to Hz/V, Absolute page Turn Instrument to Hz/V, Relative page 32 Icon Pop-up Bubbles

formed. If no prism was found, the instrument turns to the position typed in. For Aim at target: With lock the instrument locks on the prism. The icon is displayed. If no prism was found, the instrument turns to the position typed in. 5.4.4 Arrow keys The instrument can be turned using the keyboard arrow keys on the instru- ment or field controller, or the arrow keys displayed on the touch screen. When this panel is accessed, the EGL is turned on automatically. When you exit the panel, the EGL is turned off. Use the arrow keys to start the telescope movement. Press an arrow key again to speed up the movement. Press any of the other arrow keys while the instrument turns to stop the movement. Press OK to stop the instrument movement. Key Description OK To return to Leica Captivate - Home menu. Description of fields Field Option Description Speed -----, Very slow, Slow, Medium and Fast Displays the rotational speed of the instru- ment. Press the same arrow key to change the speed. 5.5 Icon Pop-Up Bubble: GS Position 5.5.1 Current position This panel shows information related to the current antenna position and the speed of the antenna. For real-time rover settings, the baseline vector is also shown. 3D viewer shows the current position in a graphical format. Description Turn Using Arrow Keys Description Icon Pop-up Bubbles 33

Page To change to another page on this panel. Fn Coord To see other coordinate types. Local coordinates are available when a local coordinate system is active. Fn Height To see height as elevation. Available when local grid coordinates are displayed. Fn Ell Ht To see height as ellipsoidal height. Available when local grid coordinates are displayed. Description of fields Field Description Position latency The latency of the computed position. Latency is mostly due to time required for data transfer and computation of position. Depends on the use of the prediction mode. Position quality and Height quality Available for phase fixed and code only solutions. The 2D coordinate and height quality of the compu- ted position. HDOP and VDOP Available for navigated solutions. Next step IF THEN the instrument is a real-time rover Page changes to the Baseline page. the instrument is not configured for real-time Page changes to the Speed page. the instrument is a real-time base OK exits Current GS position. Information on the baseline vector is displayed. Next step Page changes to the Speed page. Current GS position, Position page Current GS position, Baseline page 34 Icon Pop-up Bubbles

Field Description Horizontal speed The speed over ground in the horizontal direction. On bearing Available for local coordinate systems. The bearing for the horizontal direction related to the North direction of the active coordinate system. Vertical speed The vertical component of the current velocity. Next step IF THEN the instrument is a GS18 and the tilt compensation is active Page changes to the Tilt page. the instrument is not a GS18 or the tilt compensation on a GS18 is inac- tive OK exits Current GS position. Available for GS18 with Use tilt compensation checked in Tilt Compensa- tion. The fields are updated according to the setting for GS position update rate in Screen, Audio & Text Input. 0014298_002 b a α Direction of tilt β Tilt Current GS position, Speed page Current GS position, Tilt page Icon Pop-up Bubbles 35

Field Description Local time The current local time. Overall tilt quality The current 3D coordinate quality of the computed position. Tilt The angle between the vertical and the tilted pole of the antenna. This angle is calculated by the GS18. Tilt quality The accuracy of the tilt angle of the antenna. Direction of tilt The azimuth of the tilted antenna pole. Direction of tilt quality The accuracy of the azimuth angle of the tilted antenna pole. GS heading The direction in which the keyboard of the GS18 faces. GS heading quality The accuracy of the direction in which the keyboard of the GS18 faces. Next step OK exits Current GS position. 36 Icon Pop-up Bubbles

5.6.1 Bubble Icons Icon Description Satellite tracking Information related to the tracked satellites. Refer to "5.6.2 Satellite tracking". Data logging Information related to the logging of raw observa- tions. Refer to "5.6.3 Data logging". 5.6.2 Satellite tracking This panel shows information related to the tracked satellites ordered by the elevation angle. Key Description OK To return to the Leica Captivate - Home menu. Base / Rover To change between the SNR values of rover and base. Health To view the numbers of satellites categorised in good, bad and unavailable. More To display information about the SNR values for sat- ellites. Page To change to another page on this panel. The Gali- leo page is unavailable with GS08plus. Description of metadata Metadata Description - The Pseudo Random Noise number (GPS), the Slot number (GLONASS), the Space Vehicle number (Gali- leo, BeiDou) or the name (Terrastar) of the satellites. Elev The elevation angle in degrees. The arrows indicate if the satellite is rising or falling. Azimuth The azimuth of the satellite. Bubble icons Description Rover Satellite Track- ing, GPS/Glonass/Galileo/ BeiDou/Augmentation page Icon Pop-up Bubbles 37

L5, S/N E5b and S/N AltBOC The SNR on L1, L2 and L5 for GPS, on L1 and L2 for GLONASS, on E1, E5a, E5b and AltBOC for Galileo and on B1 and B2 for BeiDou. If the signal is not being used in the position calculations, the number is shown in brackets. Next step Page changes to another page on this panel. Shows all currently tracked satellites. Satellites below the Cut-off angle configured in Satellite Tracking are marked grey. The part of the skyplot between the 0° elevation and the cut-off angle is marked grey. Key Description OK To return to the Leica Captivate - Home menu. GPS off / GPS on To hide or show the GPS satellites (shown by the prefix G). GLO off / GLO on To hide or show the GLONASS satellites (shown by the prefix R). Available when Glonass is activated in Satellite Tracking. GAL off / GAL on To hide or show the Galileo satellites (shown by the prefix E). Available when Galileo is activated in Satellite Tracking. BDS off / BDS on To hide or show the BeiDou satellites (shown by the prefix C). Available when BeiDou is activated in Satellite Tracking. Page To change to another page on this panel. Rover Satellite Track- ing, Skyplot page 38 Icon Pop-up Bubbles

Symbol Description Satellites above the Cut-off angle configured in Satellite Tracking. Satellites below the Cut-off angle configured in Satellite Tracking. Next step Page changes to the Almanac page. The Almanac page shows • the date of the used almanacs, for each GNSS constellation configured • as shown on the skyplot, the number of satellites tracked and the number of satellites available above the cut-off elevation mask. Key Description OK To return to the Leica Captivate - Home menu. Page To change to another page on this panel. Next step OK exits the panel. The satellite tracking information shown for the base is identical with the infor- mation shown for the rover. 5.6.3 Data logging This panel shows information related to logging of raw observations. Rover Satellite Track- ing, Almanac page Base Satellite Track- ing Description Icon Pop-up Bubbles 39

Page To change to another page on this panel. Description of fields Field Description Data format Shows if raw data is saved and if so in which format. Data stored on Shows where the data is saved. Current dynamics Indicates if the instrument is static or moving. Obs logged in cur- rent interval The number of observations logged in the current interval. Static observations logged The number of static epochs recorded in the current job. Kinematic observa- tions logged The number of moving epochs recorded in the cur- rent job. DBX points logged The number of points stored to the database. Next step Page changes to the Point occupation page. Description of fields Field Description Current dynamics Shows if the instrument is moving or not. GDOP Current GDOP. Logging rate Rate at which raw observations are being recorded. Number of moving observations The number of logged moving raw observations. Reset as soon a new moving interval starts. Logging data from more than 5 sats since The time for how long five or more satellites are tracked on L1 and L2 without interruption. If fewer than five satellites were tracked, the counter is reset. The counter is not reset after Measure, Stop or Store. GNSS Data Logging Status, Logging information page GNSS Data Logging Status, Point occupation page 40 Icon Pop-up Bubbles

cessful processing. It is a conservative estimate based on a 10 ‑ 15 km baseline. The criteria used to display this value depend on the settings for Auto- matically stop point measurement in Leica Capti- vate - Home: Settings\Point storage\GS quality control. Time to go The estimated time in hours, minutes and seconds until the configured stop criteria is reached. The cri- teria used to display this value depend on the set- tings for Automatically stop point measurement in Leica Captivate - Home: Settings\Point stor- age\GS quality control. Next step Page changes to the RTK base page. As shown below, the name of the page changes depending on the type of base used. Name of page Description RTK base page Base is a real base station. Base (Nearest) page Base is the closest to the rover determined by for example SmartNet. Base (i-MAX) page Base information is individualised Master- Auxiliary corrections determined and sent by for example SmartNet. Base (MAX) page Base information is Master-Auxiliary correc- tions determined and sent by for example SmartNet. Base (VRS) page Base is a virtual base station. Base (FKP) page Base information is area correction parame- ters. Description of fields Field Option Description Logging rate A time in sec The logging rate at the base. This informa- tion is shown if the real-time message for- mat supports this information and raw observations are being logged at the base. ----- Raw observations are not being logged, or status information is not supported by RTK format. Next step OK exits GNSS Data Logging Status. GNSS Data Logging Status, RTK base page Icon Pop-up Bubbles 41

5.7.1 Bubble Icons Icon Description RTK data link stat Available when RTK is configured. Opens the status panel RTK Data Link Status or RTK1 Data Link Status/RTK2 Data Link Status. Refer to "16 RTK rover wizard". Shows also information related to the incoming data from active devices. Initialize RTK Refer to "5.7.3 Initialize RTK". Auto coord on Available for RTK data format: RTCM v3 or Leica 4G. To set an RTCM coordinate system received by a reference network as active coordinate system. Change channel To open the settings panel Radio Settings. Refer to "19.3 Radios for GPS Real-Time". Start RTK stream To start streaming RTK data. Stop RTK stream To stop streaming RTK data. 5.7.2 RTK data link stat This panel shows information related to real-time data, for example the data link and the device used to transfer real-time data. Key Description OK To exit the panel. Data To view the data being received. Depending on the RTK data format, the shown data differ. Page To change to another page on this panel. Description of fields Field Description RTK data format The received real-time data format message type. GPS used L1/L2/L5 The number of satellites on L1, L2 and L5 being used in the current position solution. Bubble icons Description RTK Data Link Status, General page 42 Icon Pop-up Bubbles

Available if Glonass is activated in Satellite Track- ing. The number of satellites on L1 and L2 being used in the current position solution. GAL used E1/E5a Available if Galileo is activated in Satellite Tracking. The number of satellites on E1 and E5a being used in the current position solution. GAL used E5b/ ABOC Available if Galileo is activated in Satellite Tracking. The number of satellites on E5b and AltBOC being used in the current position solution. BDS used B1/B2 Available if BeiDou is activated in Satellite Track- ing. The number of satellites on B1 and B2 being used in the current position solution. Last data sent Available for RTK base. Seconds since the last mes- sage from the base was sent. Last data received Available for Rover Satellite Tracking. Seconds since the last message from the base was received. In last minute Available for Rover Satellite Tracking. The percentage of real-time data received from the base compared with the data received from the antenna within the last minute. This percentage indicates how well the data link is working. RTK network Available for an Rover Satellite Tracking. The type of base network in use. Next step Page changes to the Device page. The content of this page differs for each type of device in use. Key Description OK To exit the panel. Page To change to another page on this panel. RTK Data Link Status, Device page Icon Pop-up Bubbles 43

For all devices available Field Description Name The name of the device. For RS232 Field Description Type The type of device. Port The port to which the device is connected. Bluetooth Available if device is connected using Bluetooth. Indi- cates the state of the connection. For digital cellular phones and modems Field Description Type The type of device. Port The port to which the device is connected. Firmware The software version of the attached digital cellular phone. Operator The name of the network operator in which the digi- tal cellular phone is operating. Network type The type of reference network selected in RTK Rover Settings. Refer to "RTK Rover Settings,RTK network page". Status The current mode of the digital cellular phone. The options are Unknown, Detection and Registered. Bluetooth Available if device is connected using Bluetooth. Indi- cates the state of the connection. Unavailable for CS modem. Signal Indication of received signal strength of the digital cellular phone network. For radios The available fields depend on the radio type. Field Description Type The type of device. Port The port to which the device is connected. Channel The radio channel. Frequency The current set frequency of the radio. Channel spacing Channel spacing assigned to the channel in kHz. The frequency spacing between channels depends on the radio used. Firmware The software version of the attached radio. 44 Icon Pop-up Bubbles

Field Description TCP/IP port TCP/IP port number in use. IP address IP address of the connected client. Duration The time length since when the instrument is con- nected to the Internet. KBytes received The amount of data received from the Internet in kil- obyte. KBytes sent The amount of data sent to the Internet in kilobyte. For Internet on the base Field Description TCP/IP port TCP/IP port number in use. Clients connected The number of connected clients and the number of allowed client connections as configured in Internet Port Connection. Next step Page changes to the RTK base page. As shown below, the name of the page changes depending on the type of base being used. Name of page Description RTK base page Base is a real base station. Base (Nearest) page Base is the closest to the rover determined by for example SmartNet. Base (i-MAX) page Base information is individualised Master-Auxiliary corrections determined and sent by for example SmartNet. Base (MAX) page Base information is Master-Auxiliary corrections determined and sent by for example SmartNet. Base (VRS) page Base is a virtual base station. Base (FKP) page Base information is area correction parameters. Description of fields Field Description Point ID The name of the reference. RTK base ID An identification for a base station. The ID can be converted into a compact format to be sent out with real-time data in all real-time data formats. It is dif- ferent from the point ID of the base station. RTK Data Link Status, RTK basepage Icon Pop-up Bubbles 45

antenna reference point • For RTK data format: Leica, RTK data format: Leica 4G, RTK data format: RTCM v3 or RTK data format: RTCM 9,2 v2/RTCM 1,2 v2 with RTCM version: 2.3: The antenna height at the base from the marker to the MRP. • For RTK data format: CMR/CMR+ and RTK data format: RTCM 18,19 v2 or RTK data for- mat: RTCM 18,19 v2 with RTCM version: 2.2: The antenna height at the base from the marker to the phase centre. • For all other RTK data format-----: is displayed because the data format does not include infor- mation about the antenna height. Coordinates of The coordinates for the base station which are trans- ferred depend on the active real-time data format. • For real-time messages which include antenna height and antenna type: Marker. • For real-time messages which do not include antenna information: Phase Centre of L1. Number of aux ref The number of active auxiliary base stations from which data is received. Availability depends on selec- ted network. Antenna at base The antenna used at the base. Sensor type at base The instrument type used at the base. Next step IF THEN other coordinate types must be viewed Fn Coord. Local coordinates are available when a local coordinate system is active. another page must be accessed Page. this panel must be quit OK exits the panel. This panel shows the status real-time connectivity as dynamic troubleshooting panel. It shows the success of each of the steps in the connectivity to receive real-time corrections. If one step fails or is skipped, the check box is unchecked. As each step is successfully completed, the check box is activated. The page shows the status of the DynDNS connection. This page is available, if DynDNS is activated. Refer to "18.2 CS internet / GS internet / TS Internet". ☞ Unavailable for CS35. Use the status panel in Windows. RTK Data Link Status, Connectivity page RTK Data Link Status, DynDNS page 46 Icon Pop-up Bubbles

Error DynDNS is active but the IP address could not be updated at the DynDNS service. Active DynDNS is active and has updated the IP address. Off DynDNS is inactive. Last update Display only Available on base. The time and the date of when the IP address was last updated at the DynDNS service by the GS. Current reg- istered IP Display only Available on base. The last IP address that has been updated for the GS. The following provides additional information on the satellite data received using real-time message. Information of those satellites is displayed, which are used on both base and rover. Access Data on RTK Data Link Status, General page. Key Description OK To return to RTK Data Link Status. Next sat To display information on the satellite with the next higher number. Prev sat To display information on the satellite with the next lower number. Available when Next sat was pressed before. Description of fields The data being received from the satellites and the layout of the panel depend on the active real-time data format. Real-Time Input Data Icon Pop-up Bubbles 47

or the Space Vehicle number (Galileo, BeiDou) of the satellites shown with the prefix G (GPS), R (GLO- NASS), E (Galileo) or C (BeiDou). Sat Time The GPS time of the satellite. Phase L1, Phase L2, Phase L5 The number of phase cycles from the antenna to the GPS satellite on L1, L2 and L5. Phase L1, Phase L2 The number of phase cycles from the antenna to the GLONASS satellite on L1 and L2. GAL used E1/E5a, GAL used E1/E5a The number of phase cycles from the antenna to the Galileo satellite on E1, E5a, E5b and Alt-BOC. Phase B1, Phase B2 The number of phase cycles from the antenna to the BeiDou satellite on B1 and B2. Msg 18 L1, Msg 18 L2 The uncorrected carrier phases for L1 and L2. Msg 20 L1, Msg 20 L2 The carrier phase corrections for L1 and L2. Code L1, Code L2, Code L5 The pseudorange from the antenna to the GPS satel- lite for L1, L2 and L5. Code L1, Code L2 The pseudorange from the antenna to the GLONASS satellite on L1 and L2. GAL used E1/E5a, GAL used E1/E5a The pseudorange from the antenna to the Galileo satellite on E1, E5a, E5b and Alt-BOC. Code B1, Code B2 The pseudorange from the antenna to the BeiDou satellite on B1 and B2. Msg 19 L1, Msg 19 L2 The uncorrected pseudoranges for L1 and L2. Msg 21 L1, Msg 21 L2 The pseudorange corrections for L1 and L2. 5.7.3 Initialize RTK The active working style is a real-time rover setting. If the instrument currently has a fixed solution, the initialisation starts auto- matically. The current ambiguity solution is discarded and a new initialisation is gained when the ambiguities are solved. 5.8 Icon Pop-Up Bubble: Connections 5.8.1 Bubble Icons Icon Description Bluetooth To define Bluetooth connections. Requirements Initialize RTK Bubble icons 48 Icon Pop-up Bubbles

online service that allows the data exchange between two users of the service. Refer to "29.7 Leica Exchange". Start Active Assist To connect to the Active Assist service. Refer to "5.8.2 Active Assist". End Active Assist To disconnect from the Active Assist service. 5.8.2 Active Assist Active Assist is an online support tool that allows Leica technical support to gain remote access to your instrument or field controller. Valid CCP and Active Assist licences are required to use Active Assist. 1. Establish a connection to the Internet. 2. Call your local technical support. 3. Select Start Active Assist to connect to the Active Assist service. 4. Quote the equipment number shown on the panel to your supporter. ☞ Leica technical support has now remote access to your TS instrument or field controller. 5. Select End Active Assist to disconnect from the Active Assist service once the session has finished. 5.9 Icon Pop-Up Bubble: Battery and Time 5.9.1 Bubble Icons Icon Description Change TS/GS To switch between GS and TS mode. Home To return to the Leica Captivate - Home menu. Help To start the online help. Battery / memory Information related to usage and status of battery and memory. Refer to "5.9.2 Battery / memory". Camera To capture an image with the integrated camera. Available when the cameras are activated in Leica Captivate - Home: Settings\TS instrument\Cam- eras. Refer to "5.9.3 Camera". Sketch pad To create a sketch on a virtual piece of paper. Refer to "5.9.4 Sketch pad". Description ☞ Using Active Assist step-by-step Bubble icons Icon Pop-up Bubbles 49

Key Description Page To change to another page on this panel. Description of fields Field Description Battery, Battery 1 or Battery 2 The percentage of remaining power capacity for the internal battery is displayed numerically. If no infor- mation for a field is available, for example no battery is inserted, then ----- is displayed. ☞ On the MS60/TS60, if the battery gets charged, (charging) is stated behind the percentage of the battery power level. ☞ When the battery is getting low on the TS, a warning message is displayed on the CS. TS external power, GS external power or CS external power Shows if an external power supply is connected. If an external battery is connected, the percentage of remaining power capacity is displayed numerically. Applies also to wall plugs. Internal memory, SD card or USB stick The total/free memory for data storage on the data storage device. If no information for a field is availa- ble, for example no data storage device is inserted, then ----- is displayed. ☞ The CS35 has two USB ports. The USB stick, that was inserted first, is used. 5.9.3 Camera 1. Aim the camera to the desired target. 2. Check the view at the display. 3. Click Capture to take the picture. ☞ Capture changes to Store. 4. Click Store. ☞ The image is stored in the DBX\JOB\IMAGES folder of the data storage device. Battery & Memory Taking a picture step- by-step 50 Icon Pop-up Bubbles

image. 5.9.4 Sketch pad The field sketch functionality is used to create a sketch on virtual paper. Sketching is possible on predefined or on user-defined templates. User-defined templates can, for example, include a company logo or check boxes for tasks that must be done. The sketch is stored as image in jpg format. The jpg file is stored in the DBX \JOB\IMAGES folder of the data storage device. The predefined templates are optimised for A4 printout. User-defined tem- plates can be optimised for any format. A screenshot cannot be made from the field sketch. Key Description OK To create a copy of the selected sketch template and to start sketching. Description of fields Field Option Description Sketch tem- plate Plain paper, Lined paper- narrow, Lined paper- wide, Grid paper (small grid) or Grid paper (large grid) The predefined sketch templates. Description Choose Sketch Tem- plate Icon Pop-up Bubbles 51

with a maximum of five megapixels. The tem- plates are stored in the CONFIG\SKETCH_TEM- PLATES folder of the data storage device. To make a user-defined template selectable in the list, transfer the template to the internal memory in Leica Captivate - Home: Set- tings\Tools\Transfer user objects. Refer to "29.1 Transfer user objects". Next step Select a template. OK to access Sketch Pad. Refer to "Tools" for information on the toolbar. Key Description Store To store and link the field sketch. Sketch Pad 52 Icon Pop-up Bubbles

6.1 Overview Jobs • structure surveying projects. • contain all points, lines, images and scans that are measured/recorded and stored. • can be downloaded to Infinity for post-processing or for data transfer to a further program. • can be uploaded from Infinity, for example, for stake out operations. • can be stored on the data storage device or the internal memory. • Data jobs. Explained in this chapter. • DTM files. Refer to "51.6 Staking Out a DTM or Points & DTM". • Road alignment files. A default job is available on the instrument after formatting the data storage device, inserting a previously formatted data storage device or deleting all jobs. Data is stored to a job. After formatting the data storage device, the default job is used until a user-defined job is created and selected. The properties of the job determine some system properties, such as the codelist, coordinate system and TS scale factor. When a job becomes the job, then the sort and filter settings of this job are saved in the System RAM. If the data storage device is formatted then these last used sort and filter settings are used for the default job. 6.2 Creating a New Job Select Leica Captivate - Home: Tap here to create new job. OR In Leica Captivate - Home press Fn New job. Key Description Store To store the settings. Page To change to another page on this panel. Description Type of jobs Default job Job Access New Job, General page Job Menu - Jobs 53

Field Option Description Name Editable field A unique name for the new job. The name can be up to 16 characters long and include spaces. Input required. Description Editable field Two lines for a detailed description of the job, for example, work to be performed or the classes contained in the job. Input optional. Creator Editable field The name of the person who is creating the job. Input optional. Job stored to Selectable list The device on which the new job is stored. Depending on the instrument options, this field may be a display only field. ☞ For CS35: Jobs must be created on the internal memory. The creation of jobs on the USB stick is not sup- ported. ☞ For jobs stored on the SD card, the icon is shown on the job tile in the Leica Captivate - Home menu. Display in job carousel Check box When this box is checked, the job is visible in the job carousel. When this box is not checked, the job is invisible in the job carousel. Exclude jobs from the job carousel to reduce the scrolling effort. After stor- ing job, cap- ture an image to display in the Home screen Check box When this box is checked: After pressing Store, the camera on the current instrument will start. A picture can then be captured. The picture is automatically added to the job image in Leica Captivate - Home. Next step Page changes to the Coordinate system page. Description of fields Field Option Description Coordinate system Selectable list Choosing a coordinate system attaches it to the job. A coordinate system is necessary to transform GNSS coordinates to a local grid format. All other fields on this panel are display only fields. They depend on the transformation type of the selected coordinate system. New Job, Coordinate system page 54 Job Menu - Jobs

Description of fields Field Option Description Codelist Selectable list Choosing a codelist copies the codes to the job. Codes are editable. Refer to "6.5 Managing Job Codes". Next step Page changes to the Linked jobs page. Multiple jobs can be linked to a working job. The advantage is, that the list of design points and lines available to be used in some applications can be read from these multiple linked jobs, instead of one single control job. Linked jobs will overwrite the points and lines from the global design job selec- ted in Design Data. The source for a control job must be a job from Leica Captivate. A external format, such as ASCII, XML or DXF must be converted into DBX for- mat first. Key Description Store To store the settings. Add To link a control job to the job. Accesses Choose Linked Jobs. Refer to " Choose Linked Jobs". Remove To delete the highlighted control job from the list of linked jobs. The corresponding points and lines will be removed from the data set. Dataset To list all points and lines contained in the available and visi- ble linked jobs. The list is updated with the data from the selected jobs to link. Refer to " Dataset". Page To change to another page on this panel. Fn Main job To make a linked job the main job where created points and lines are stored to. Fn Log To view, edit and delete points and lines stored with the job. Points and lines are sorted by time in one list. Fn State To change between the options in the metadata for State. To show or hide the linked job data within the data set. Description of metadata Metadata Description - The name of the job. New Job, Codelist page New Job, Linked jobs page Job Menu - Jobs 55

• Visible: The data of the linked job are included in the data set. • Hidden: The data of the linked job are excluded from the data set. • Not available:The source job of the data is not available on any of the data storage devices. Main Job Created control data such as points and lines are stored in the main job. To make a job the main job, highlight the job and press Fn Main job. As long as there is at least one available linked job, there must be a main job where the created points and lines are stored if created. If no linked job is available, for example all are deleted, or all are on an SD card which is not inserted, then there is no main job. If the main job is deleted, then the role of main job jumps to another linked job. If the main job is set as Hidden, the role of main job stays in that job. Source The data storage device where the job is stored. If the working job and/or linked jobs are moved to another device, the link between both is remembered. Source: ----- indicates that the source job of the data is not available in the expected data storage device. ☞ If the data storage device containing one or more control jobs is taken out off the instrument, the jobs will NOT be available in the data set anymore. ☞ Every time an app is started, the availability of control jobs is checked. The check ensures the cor- respondency between the list of linked jobs and the data set. Date cre- ated The date of when the job was created. Next step Page changes to the CAD files page. If a CAD file is checked, the file is attached to the job when Store is pressed. The CAD file can be in the \DATA folder of any data storage device. The new job and the CAD file do not have to be on the same data storage device. CAD heights are supported. Key Description Store To store the settings. Selected CAD files are available in the job as background maps. Add To add another CAD file to the job. Remove To delete a CAD file. New Job, CAD files page 56 Job Menu - Jobs

Page To change to another page on this panel. Fn Settings To define CAD import settings. The settings are applied when importing the CAD data from within the 3D viewer. Fn Layers To turn CAD layers on or off. Fn Log To view logged data. Description of metadata Metadata Description - The name of the CAD files available in the \DATA directory of any data storage device. Format The format of the CAD file: dxf, shp or Leica for CAD files that are already attached to other jobs and converted to Leica format. Size (MB) The size of the CAD file in megabytes. Source The data storage device where the CAD file is stored. Unit The units used for the CAD file. Next step Page changes to the Linked design data page. ☞ The design data selected in this panel, are local design data. In the 3D viewer and when using the apps. the global design data will be overwritten by linked design data from the working job. Key Description Store To store the settings. Page To change to another page on this panel. Fn Log To view logged data. Description of fields Field Option Description Use a DTM Check box When this box is checked, a DTM job can be selected. A DTM job holds DTM (Digital Ter- rain Model) or TIN (Triangular Irregular Net- work) data. The files are stored in the \DBX folder or a subfolder of \DBX. DTM Selectable list Holds DTM (Digital Terrain Model) data or TIN (Triangular Irregular Network) data. The DTM job to be used must be stored in the \DBX directory on the active data storage device. The DTM job is a read-only source of infor- mation and cannot be selected as a job. New Job, Linked design data page Job Menu - Jobs 57

the 3D viewer. Layer Display only or selectable list A DTM job can consist of multiple DTM layers or surfaces. These DTM layers can cover dif- ferent locations, be on top of each other or intersect each other. If there is only one layer in the DTM job, the layer name is displayed as an output. If there are multiple layers, the layer to display in 3D viewer can be selected. Date cre- ated Display only The date of when the job was created. Use a road design Check box When this box is checked, a road design can be selected. Contains all the information about the road design. For example, the geometry of the line, the formation layer of the road or the information related to the construction of cuttings and embankments. Road design Selectable list The files are stored in the \DBX folder or a subfolder of \DBX. The data is either typed in manually in the Alignment editor app or converted from a road design package. The road job is a read-only source of infor- mation and cannot be selected as a job. The selected Road design is visible in 3D viewer. Use a rail design Check box When this box is checked, a rail job can be selected. Rail design Selectable list Contains all the information about the rail design including the geometry of the centre- line and the rail definition (superelevation). The files are stored in the \DBX folder or a subfolder of \DBX. The rail job is a read-only source of informa- tion and cannot be selected as a job. The selected Rail design is visible in 3D viewer. Use a tun- nel design Check box When this box is checked, a tunnel job can be selected. Tunnel design Selectable list Contains all the information about the tunnel design including the geometry of the centre- line and the tunnel profile. The files are stored in the \DBX folder or a subfolder of \DBX. The tunnel job is a read-only source of infor- mation. The selected Tunnel design is visible in 3D viewer. 58 Job Menu - Jobs

The geometric distance correction (geometric ppm) is derived from the map projection distortion (map projection ppm), the height above reference datum correction (height ppm) and an individual correction (individual ppm). The calculation of the map projection ppm follows the formula for the Trans- versal Mercator Projection. The individual factors are: the scale factor of the line of projection central meridian, Gauss-Krüger = 1.0, UTM = 0.9996, and so on, and the offset from the line of projection. The calculation of the height ppm is derived from the height of the instrument setup above the reference datum. Normally this is the height above mean sea- level MSL. Key Description Store To store the settings. Page To change to another page on this panel. Fn ppm=0 To set Geometric ppm: 0.0. Description of fields Field Option Description Scale TS measure- ments Check box When this box is unchecked, the scale factor is automatically set to 1. When this box is checked, the scale factor can be computed based on various options. Compute scale from User entered scale fac- tor To enter only the scale factor. User entered ppm To enter only the geometric ppm value. Current setup To calculate the ppm/scale factor automatically from the coordinate system and setup position. Projec- tion & height info To enter all values for determining the geometric ppm. New Job, TS scale page Job Menu - Jobs 59

Compute scale from: User entered scale fac- tor. PPM Editable field The individual ppm value. Available for Compute scale from: Projection & height info and Compute scale from: User entered ppm. Map pro- jection ppm Display only The map projection ppm value. If this value cannot be calculated, then ----- is displayed and is also ignored in the calculation of the geometric ppm value. Available for Compute scale from: Projection & height info and Compute scale from: Current setup. Height ppm Display only The height ppm value calculated from the height coordinates of the current setup stored in the internal memory. If this value cannot be calcula- ted, then ----- is displayed and is also ignored in the calculation of the geometric ppm value. Available for Compute scale from: Projection & height info and Compute scale from: Current setup. Geomet- ric ppm Display only For Projection & height info: Geometric ppm = Map projection ppm + PPM + height ppm value calculated fromGround height. For Current setup: Geometric ppm = Map projection ppm + Height ppm. Scale at CM Editable field The scale at the central meridian. Available for Compute scale from: Projection & height info. Offset to CM Editable field The offset to the central meridian. Available for Compute scale from: Projection & height info. Ground height Editable field The height of the instrument setup above the ref- erence datum. Available for Compute scale from: Projection & height info. Additional calculation method for the geometric ppm value The geometric ppm value can also be calculated by a resection calculation. The scale factor from the resection is used for PPM. Individual ppm=(s-1)*106.s=1+ppm*10-6. The Geometric ppm value is calcu- lated with the following: • Scale at CM: 1, • Offset to CM: 0, • Map projection ppm: 0 and • Ground height: 0. 60 Job Menu - Jobs

When Compute scale from: Current setup: • the ppm values for Map projection ppm, Height ppm and Geometric ppm are automatically calculated. The coordinates of the current instru- ment setup stored in the internal memory are used, which are based on the currently active coordinate system. • each time an app is accessed, the geometric ppm value is automatically calculated. The coordinates of the current instrument setup stored in the internal memory are used (these coordinates may have been updated), which are based on the currently active coordinate system (this coordinate system may have changed). This way, the user is always working with the correct geometric ppm value. • when the None coordinate system is chosen, then the geometric ppm value cannot be automatically calculated. A message appears, allowing the user to either manually enter the ppm values or accept ppm values of 0. All jobs on the available data storage devices are listed. Select the jobs you want to link. Check a box if you want to link the control job to the job. Key Description OK To return to New Job, Linked jobs page. Check box behaviour Description Checks or unchecks the check box of the highlighted job. The behaviour depends on the current status of the check box. Checks or unchecks the check box of the highlighted job. The behaviour depends on the current status of the check box. Move the focus on the screen upwards. Move the focus on the screen downwards. Tapping the check box Checks or unchecks the check box depending on the current status of the check box. Highlights the line. Space bar Starts the job search. Description of metadata Metadata Description - The name of the job. Choose Linked Jobs Job Menu - Jobs 61

Date cre- ated The date of when the job was created. The panel is similar to the panel that opens when View & edit data was selected from the job menu. Refer to "7.2 Accessing Data Management" for a description of the panel. The differences are: • All changes done in the data set are applied to the original jobs. • For the key New: To create a point/line. New points/lines are stored in the main job and then displayed in the data set. • For the metadata, Source is displayed. The linked job to which the point belongs. • On the 3D viewer page, the points and lines from the linked jobs are dis- played. Selected filters for the data set points are applied. The Dataset panel can also be accesses by a hot key or a favourites keys. 6.3 Choosing a Job Select Leica Captivate - Home:Tap here to choose design data. The pages that are always shown are: Points & lines and DTM. The pages, Road, Rail and Tunnel are only shown if the appropriate app is loaded. ☞ The design data selected in this panel, are global design data. In the 3D viewer and when using the apps. the global design data will be overwritten by linked design data from the working job. Key Description OK To accept the selected job. Page To change to another page on this panel. Fn Settings To activate or deactivate job selection at the beginning of an app. Dataset Access Design Data 62 Job Menu - Jobs

Field Option Description Use points & lines data Check box When this box is checked, a separate design job can be selected. Target points can be selected from the design job. Individual lines and/or points of a separate design job can be staked out. The selected design job is visible in 3D viewer. Name Selectable list Control points or lines are stored in the design job. The design job holds all control point information needed in the field, for example, control points, points with known coordinates used for a TS setup. Lines of the design job can be used for Stake to line or Measure to line. A CAD file attached to a design job can be used to view and import the CAD lines for working with. Description Display only The detailed description of the job. Date cre- ated Display only The date of when the job was created. Last used Display only The date of when the job was last accessed. Use a DTM Check box When this box is checked, a DTM job can be selected. A DTM job holds DTM (Digital Ter- rain Model) or TIN (Triangular Irregular Net- work) data. The files are stored in the \DBX folder or a subfolder of \DBX. DTM Selectable list Holds DTM (Digital Terrain Model) data or TIN (Triangular Irregular Network) data. The DTM job to be used must be stored in the \DBX directory on the active data storage device. The DTM job is a read-only source of infor- mation and cannot be selected as a job. ☞ The selected DTM job is visible in the 3D viewer. Layer Display only or selectable list A DTM job can consist of multiple DTM layers or surfaces. These DTM layers can cover dif- ferent locations, be on top of each other or intersect each other. If there is only one layer in the DTM job, the layer name is displayed as an output. If there are multiple layers, the layer to display in 3D viewer can be selected. Job Menu - Jobs 63

design Check box When this box is checked, a road design can be selected. Contains all the information about the road design. For example, the geometry of the line, the formation layer of the road or the information related to the construction of cuttings and embankments. Road design Selectable list The files are stored in the \DBX folder or a subfolder of \DBX. The data is either typed in manually in the Alignment editor app or converted from a road design package. The road job is a read-only source of infor- mation and cannot be selected as a job. The selected Road design is visible in 3D viewer. Use a rail design Check box When this box is checked, a rail job can be selected. Rail design Selectable list Contains all the information about the rail design including the geometry of the centre- line and the rail definition (superelevation). The files are stored in the \DBX folder or a subfolder of \DBX. The rail job is a read-only source of informa- tion and cannot be selected as a job. The selected Rail design is visible in 3D viewer. Use a tun- nel design Check box When this box is checked, a tunnel job can be selected. Tunnel design Selectable list Contains all the information about the tunnel design including the geometry of the centre- line and the tunnel profile. The files are stored in the \DBX folder or a subfolder of \DBX. The tunnel job is a read-only source of infor- mation. The selected Tunnel design is visible in 3D viewer. Next step Open the selectable list for jobs to view job metadata, data, create, edit or delete jobs. 64 Job Menu - Jobs

depending on the device. Key Description OK To select the highlighted job and to return to the panel from where this panel was accessed. New Available for design jobs. To create a job. Refer to "6.2 Creat- ing a New Job". Edit Available for design, Road, Rail and Tunnel jobs. To edit the highlighted job. Refer to "6.4 Editing a Job". Delete To delete the highlighted job, including all map files from attached CAD files. Data Available for design, Road, Rail and Tunnel jobs. To view, edit and delete points, lines, images and scans stored with the job. Points, lines, images and scans are shown on separate pages. Selected sort and filter settings apply. ☞ For Road, Rail or Tunnel jobs, review of the align- ment design data, and edit the start chainage or centreline. A review of all design elements as well as a 3D viewer is available. 6.4 Editing a Job In the Job Properties:, the settings for a job can be viewed and changed. From the job menu, select View & edit job properties. The fields on this page are identical with the fields in New Job, General. Refer to "6.2 Creating a New Job". Choose Design Data, DTM, Road Design, Rail Design, Tunnel Design Description Access Job properties, General page Job Menu - Jobs 65

Data To view, edit and delete points and lines stored with the job. Points and lines are shown on separate pages. Selected sort and filter settings apply. Page To change to another page on this panel. Fn Log To view, edit and delete points and lines stored with the job. Points and lines are sorted by time in one list. Next step Page changes to the CAD files page. Refer to "New Job,Codelist page" for information on the Coordinate system page. Key Description Store To store the settings. Import To add extra codes from a new codelist to the job. The name of this codelist is copied to the job. Codes To view codes currently stored in the job. Refer to "6.5 Man- aging Job Codes". Data To view, edit and delete points and lines stored with the job. Points and lines are shown on separate pages. Selected sort and filter settings apply. Page To change to another page on this panel. Fn Export To copy codes from the job to an existing or new codelist. Fn Log To view, edit and delete points and lines stored with the job. Points and lines are sorted by time in one list. Description of fields Field Option Description Codelist No codes are stored in the job. This default setting can be changed. Choose a codelist to copy the codes to the job. Job properties, Codelist page 66 Job Menu - Jobs

If codes had been copied from a codelist in the internal memory, the name of the codel- ist is displayed. If codes have been typed in, then the name of the job is displayed. Next step Page changes to the Linked jobs page. Multiple jobs can be linked to a working job. The advantage is, that the list of design points and lines available to be used in some applications can be read from these multiple linked jobs, instead of one single control job. The source for a control job can be: The source for a control job must be a job from Leica Captivate. A external format, such as ASCII, XML or DXF must be converted into DBX for- mat first. Key Description Store To store the settings. Add To link a control job to the job. Accesses Choose Linked Jobs. Refer to " Choose Linked Jobs". Remove To delete the highlighted control job from the list of linked jobs. The corresponding points and lines will be removed from the data set. Dataset To list all points and lines contained in the available and visi- ble linked jobs. The list is updated with the data from the selected jobs to link. Refer to " Dataset". Page To change to another page on this panel. Fn Main job To make a linked job the main job where created points and lines are stored to. Fn Log To view, edit and delete points and lines stored with the job. Points and lines are sorted by time in one list. Fn State To change between the options in the metadata for State. To show or hide the linked job data within the data set. Description of metadata Metadata Description - The name of the job. State The state of the job: • Visible: The data of the linked job are included in the data set. • Hidden: The data of the linked job are excluded from the data set. • Not available:The source job of the data is not available on any of the data storage devices. Job properties, Linked jobs page Job Menu - Jobs 67

the main job. To make a job the main job, highlight the job and press Fn Main job. As long as there is at least one available linked job, there must be a main job where the created points and lines are stored if created. If no linked job is available, for example all are deleted, or all are on an SD card which is not inserted, then there is no main job. If the main job is deleted, then the role of main job jumps to another linked job. if the main job is set as Hidden, the role of main job stays in that job. Source The data storage device where the job is stored. If the working job and/or linked jobs are moved to another device, the link between both is remembered. Source: ----- indicates that the source job of the data is not available in the expected data storage device. ☞ If the data storage device containing one or more control jobs is taken out off the instrument, the jobs will NOT be available in the data set anymore. ☞ Every time an app is started, the availability of control jobs is checked. The check ensures the cor- respondency between the list of linked jobs and the data set. Date cre- ated The date of when the job was created. Next step Page changes to the CAD files page. Key Description Store To store the settings. Add To select a CAD file to be added to the job properties. The panel that opens is similar to New Job, CAD files page. Refer to "6.2 Creating a New Job" for a description of the panel. Job properties, CAD files page 68 Job Menu - Jobs

displayed in the CAD Files panel. The files listed are all dxf, shp files and mpl files from the \Data directory on a data storage device or in the internal memory. If an mpl file is selected, then this file, including all related files, is copied to the appropriate job folder. Remove To delete the highlighted Map file from the job. ☞ If deleted accidentally, the file must be attached again. State To show or hide the CAD data. Page To change to another page on this panel. Fn Settings To configure the CAD file import parameters. Refer to "CAD Import". Fn Layers To change to the CAD layers panel. On this panel, it is possi- ble to make layers from the CAD file visible or hidden for 3D viewer. Fn Log To view, edit and delete points and lines stored with the job. Points and lines are sorted by time in one list. Description of metadata Metadata Description - The name of the CAD files that can be used. The files displayed are the converted Leica Map files (*.mpl) within the job. The original file extension is added to the file name with an underscore, for example example_dxf. State If set to Visible, the CAD file is visible as background map in 3D viewer. Next step Press Page to change to the Linked design data page. OR Press Fn Layers to access CAD Layer Management. OR Press Fn Settings to access CAD Import. ☞ The design data selected in this panel, are local design data. In the 3D viewer and when using the apps. the global design data will be overwritten by linked design data from the working job. Key Description Store To store the settings. Page To change to another page on this panel. Fn Log To view logged data. Job properties, Linked design data page Job Menu - Jobs 69

Field Option Description Use a DTM Check box When this box is checked, a DTM job can be selected. A DTM job holds DTM (Digital Ter- rain Model) or TIN (Triangular Irregular Net- work) data. The files are stored in the \DBX folder or a subfolder of \DBX. DTM Selectable list Holds DTM (Digital Terrain Model) data or TIN (Triangular Irregular Network) data. The DTM job to be used must be stored in the \DBX directory on the active data storage device. The DTM job is a read-only source of infor- mation and cannot be selected as a job. ☞ The selected DTM job is visible in the 3D viewer. Layer Display only or selectable list A DTM job can consist of multiple DTM layers or surfaces. These DTM layers can cover dif- ferent locations, be on top of each other or intersect each other. If there is only one layer in the DTM job, the layer name is displayed as an output. If there are multiple layers, the layer to display in 3D viewer can be selected. Date cre- ated Display only The date of when the job was created. Use a road design Check box When this box is checked, a road design can be selected. Contains all the information about the road design. For example, the geometry of the line, the formation layer of the road or the information related to the construction of cuttings and embankments. Road design Selectable list The files are stored in the \DBX folder or a subfolder of \DBX. The data is either typed in manually in the Alignment editor app or converted from a road design package. The road job is a read-only source of infor- mation and cannot be selected as a job. The selected Road design is visible in 3D viewer. Use a rail design Check box When this box is checked, a rail job can be selected. Rail design Selectable list Contains all the information about the rail design including the geometry of the centre- line and the rail definition (superelevation). The files are stored in the \DBX folder or a subfolder of \DBX. 70 Job Menu - Jobs

tion and cannot be selected as a job. The selected Rail design is visible in 3D viewer. Use a tun- nel design Check box When this box is checked, a tunnel job can be selected. Tunnel design Selectable list Contains all the information about the tunnel design including the geometry of the centre- line and the tunnel profile. The files are stored in the \DBX folder or a subfolder of \DBX. The tunnel job is a read-only source of infor- mation. The selected Tunnel design is visible in 3D viewer. Key Description Store To store the settings. State To change between the options in the metadata for State. All To make all layers have the same state as the currently high- lighted layer. Description of metadata Metadata Description - The name of the layer. For dxf files, all layers are listed, no matter if the layer is fil- led or empty. CAD Layer Manage- ment Job Menu - Jobs 71

• Hidden These layers are not shown on the 3D viewer page and their positions are not used when zooming to extents. Nothing in these layers can be selected. • Visible These layers are shown on the 3D viewer page and their positions are used when zooming to extents. Nothing in these layers can be selected. Empty dxf layers can be set to visible. • Selectable These layers are shown on the 3D viewer page and their positions are used when zooming to extents. Objects on these layers are available to be selected. Description of fields Field Option Description Prefix to use for points, Pre- fix to use for lines or Prefix to use for closed lines Editable field The identifier with up to four characters is added in front of the ID of the imported CAD points, lines or areas. Objects to create when importing entities Vertices and lines • Imports the CAD lines into the job. • Creates points at the starting and the ending coordinates of the imported line/arc/polyline elements. Only at ver- tices Creates points at the starting and the ending coordinates of the line/arc/polyline elements. The elements are not imported. Only lines Imports only the CAD lines into the job. No points are created. Ignore data at height Editable field Height values inside the DXF file are consid- ered invalid and are not converted. Apply a height to 2D data Check box When this box is checked, a height can be defined which is then applied to all imported 2D CAD points. Height to apply Editable field Available when Apply a height to 2D data is checked. The height to apply to 2D CAD points. CAD Import 72 Job Menu - Jobs

Check box When this box is checked then the values for the extents defined in the dxf file will be ignored. This may be necessary if these val- ues are very large meaning that the data will not be displayed in the 3D viewer after importing or attaching the file. When this box is not checked then the val- ues in the dxf file for the extents are used. All jobs on the available data storage devices are listed. Select the jobs you want to link. Check a box if you want to link the control job to the job. Key Description OK To return to New Job, Linked jobs page. Check box behaviour Description Checks or unchecks the check box of the highlighted job. The behaviour depends on the current status of the check box. Checks or unchecks the check box of the highlighted job. The behaviour depends on the current status of the check box. Move the focus on the screen upwards. Move the focus on the screen downwards. Tapping the check box Checks or unchecks the check box depending on the current status of the check box. Highlights the line. Space bar Starts the job search. Description of metadata Metadata Description - The name of the job. Source The data storage device where the job is stored. Date cre- ated The date of when the job was created. Choose Linked Jobs Job Menu - Jobs 73

selected from the job menu. Refer to "7.2 Accessing Data Management" for a description of the panel. The differences are: • All changes done in the data set are applied to the original jobs. • For the key New: To create a point/line. New points/lines are stored in the main job and then displayed in the data set. • For the metadata, Source is displayed. The linked job to which the point belongs. • On the 3D viewer page, the points and lines from the linked jobs are dis- played. Selected filters for the data set points are applied. The Dataset panel can also be accesses by a hot key or a favourites keys. 6.5 Managing Job Codes To view, edit, group and sort all codes currently stored in the job. 1. Select View & edit job properties from the job menu in Leica Captivate - Home. 2. Page until the Codelist page is active. 3. When creating a job: Open the selectable list for Codelist. 4. When editing a job: Edit 5. Codes to access Job Codes. Key Description OK To return to the previous panel. New To create a code. Refer to "8.4.2 Creating/Editing a Code". Edit To edit the highlighted code. Accesses Edit Code where new attributes can be added to a code and line styles can be changed. Fn Group To access Code Groups. To view, create, activate and deacti- vate code groups. Refer to "8.5 Managing Code Groups". Fn Sort To access Sort Codes. To sort codes by code name, code description, quick code or last used. Dataset Description Access step-by-step Job Codes 74 Job Menu - Jobs

Key Description Store To store the code including any newly created attributes. New attrb To add an attribute to a code. The behaviour of this panel varies with the type of code to be edited. When creating a job, more code metadata are editable. When editing a job, less code metadata are editable. The differences are explained in the table. Type of code Description Point codes • New attributes can be added with New attrb. • For new jobs: The line style, line colour and string num- ber can be changed. This selections are stored to the code. Free codes New attributes can be added with New attrb. For attributes for which an attribute name can be typed in: Tap on the field of the attribute name or the field for the attribute value. The name of the attribute can be edited and an attribute value can be typed in. Edit Code Job Menu - Jobs 75

7.1 Overview Data management is the administration of data stored in the job, including • viewing data and related information. • editing data. • creating new data. • deleting existing data. • filtering existing data. 7.2 Accessing Data Management Select View & edit data from the job menu. The objects listed on the pages belong to the edited job. The objects listed and their order depend on the active sort and filter settings. Refer to "7.6 Point Sorting and Filters" for information about sort and filter settings. Check one or multiple points for editing. Use Fn All to select all points at once. Key Description OK To close the panel and return to the panel from where this panel was accessed. New To create a point. Edit To edit the highlighted point. In case of multiple point selection, editing the target height for all selected points is possible. ☞ Editing the target height for multiple points is pos- sible for TS points of class Measured, Adjusted and None. Delete To delete the highlighted point. In case of multiple point selection, all selected points are deleted. More To display information about the codes and code information if stored with any point, the 3D coordinate quality, the class, Easting, Northing and Elevation, the time and the date of when the point was stored. Description Access ☞ Job name, Points page 76 Job Menu - View & edit data

umns are shown depends on the Grid format configured to be used in Regional, Coordinates page. ☞ The Easting, Northing and Elevation values are shown in the unit configured in Regional, Dis- tance page. Page To change to another page on this panel. FnLog To view points, lines and free codes stored with the job sor- ted by time. Refer to "7.5 Data Log". Fn Filter To define sort and filter settings. Refer to "7.6 Point Sorting and Filters". Fn All or Fn None To select or deselect all points at once. Check box behaviour Action Description Checks or unchecks the check box of the highlighted point. The behaviour depends on the current status of the check box. Checks or unchecks the check box of the highlighted point. The behaviour depends on the current status of the check box. Move the focus on the screen upwards. Move the focus on the screen downwards. Tapping the check box Checks or unchecks the check box depending on the current status of the check box. Highlights the line. Tapping the image linked to the point Enlarges the images. Highlights the line. Space bar Starts the point search. Description of symbols The symbols match the symbols in the 3D viewer. Job Menu - View & edit data 77

Point of class Adjusted (Adj) or Average (Avge) Point of class Reference (Ref) Point of class Measured (Meas) Single Point Position uploaded from Infinity Point of class Navigated (Nav) or Estimated (Est) Point measured within a Stake app Next step Page changes to the Lines page. Key Description OK To close the panel and return to the panel from where this panel was accessed. New To create a line. After storing the new line, all existing lines which are open are closed. Refer to "7.4.2 Creating a New Line". Edit To edit the highlighted line. Delete To delete the highlighted line. Job name, Lines page 78 Job Menu - View & edit data

line, the start time, the end time of when the last point was added to the line, the length of the line, the perimeter and the area. Page To change to another page on this panel. Fn Filter To define sort and filter settings. Refer to "7.6 Point Sorting and Filters". Description of metadata Metadata Description - The listed lines already stored in the job. Closed The status of a line. If a line is closed, it means that it is physically closed onto itself, effectively becoming an area. Next step Page until the 3D viewer page is active. For information on camera and images refer to "32.4 Image Management". Check one or multiple scans for a perspective display of the 3D point clouds in the 3D viewer. Use Fn All to select all scans at once. Key Description OK To close the panel and return to the panel from where this panel was accessed. Page To change to another page on this panel. Fn Delete To delete the highlighted scan. Fn All or Fn None To select or deselect all scans at once. Description of metadata Information about the date, the time, the status and the number points. 7.3 Point Management 7.3.1 Creating a New Point In Job name, Points page, press New. ☞ Job name, Scans page Access Job Menu - View & edit data 79

tion. North or South Available for local geodetic or WGS 1984 geodetic coordi- nates when WGS84 latitude is highlighted. Changes between North and South latitude. East or West Available for local geodetic or WGS 1984 geodetic coordi- nates when WGS84 longitude is highlighted. Changes between East and West longitude. Next To store the point and to remain in the panel. The point ID increments according to point ID template. Page To change to another page on this panel. Fn Coord To view other coordinate properties. Fn Tools For an individual name independent of the ID template or to change back to the next ID from the configured ID template. Description of fields Field Option Description Point ID Editable field The name of the new point. The configured point ID template is used. The ID can be changed in the following ways: • To start a new sequence of point IDs, type over the point ID. • For an individual name independent of the ID template Fn Tools and then Indi- vidual point ID. Fn Tools and then Sequential point ID changes back to the next ID from the configured ID tem- plate. Coordinate fields Editable field Negative geodetic coordinates are interpre- ted as being of the opposite hemisphere or other side of the central meridian. For exam- ple, entering -25 °N is stored as 25 °S, enter- ing -33 °E is stored as 33 °W. Next step Page changes to the Code page. New Point, Coordinates page 80 Job Menu - View & edit data

\Customisation\Coding determine the availability of the subsequent fields and softkeys. Key Description Store To store the new point entered and all associated informa- tion. New attrb To create more attributes for this point code. Last To recall the last used attribute values which were stored with this point code. Default To recall the default attribute values for the selected code. Page To change to another page on this panel. Description of fields Field Option Description Point code Selectable list The codes from the job codelist are used. All point codes of the job codelist can be selected.The description of the code is shown as a display only field. The attributes are shown as display only, editable fields or selectable lists depending on their definition. Editable field Codes for points can be typed in. A check is performed to see if a point code of this name exists in the job. If so, an infor- mation message is displayed. If Suggested attribute values: Last used in Coding, the attributes are also shown. Attribute Editable field Up to 20 attribute values are available. Next step Store stores the new point entered and all associated information. The properties stored with the point are: • Class: Control • Sub class: Fixed (Pos & Ht) • Source: User entered • Instrument source: GS New Point, Code page Job Menu - View & edit data 81

codes and/or attribute values of the new and the existing point do not match, a panel opens where they can be corrected. 7.3.2 Editing a Point In Job name, Points page, press Edit. ☞ If multiple points are selected when Edit is pressed, only the target height is editable. Editing the target height for multiple points is pos- sible for TS points of class Measured, Adjusted and None. The visible pages on this panel depend on the properties of the point being edited. It is possible to edit the point ID and for points of Class: Control and Class: Estimated also the coordinates. Other point-related data is shown in display only fields. ☞ Changing the point ID of a point, applies this new point ID to all other points with the same original name, regardless of their class. ☞ Points of Class: Reference cannot be renamed. ☞ Changing coordinates of a point which has been previously used in other apps, for example COGO, or hidden point measurements does not update the app results. ☞ An edited point retains the creation value for Time. Key Description Store To store the changes. Previous To display the previous point in the list of points displayed in Job name, Points page. Available unless the beginning of the list is reached. Next To display the next point in the list of points displayed in Job name, Points page. Available unless the end of the list is reached. More To display information about class, sub class, 3D coordinate quality, time and date of when point was stored, instru- ment source, source and the flag for Linework if available. Page To change to another page on this panel. Fn Coord To view other coordinate properties. ☞ Access Point ID, Coordinates page 82 Job Menu - View & edit data

Fn Height Available for local coordinates. Changes between the ellip- soidal and the orthometric height. Changing the height type does not edit the point. Next step Page changes to the next page. On this page, the stakeout results are displayed. ☞ When changing Target height on the Obs page, the Measured height value is updated. The offset values used for staking the point will not be editable on the Offset page. Key Description Store To store the changes. Page To change to another page on this panel. Description of fields Field Option Description Design point ID Display only The name of the design point that was staked. Difference in easting Display only The difference between the Design easting and the Measured easting. Difference in northing Display only The difference between the Design north- ing and the Measured northing. Cut/Fill Display only The height difference between the Design height and the Measured height. 2D distance Display only Displays the horizontal difference between the design point and the staked point. 3D distance Display only Displays the spatial difference between the design point and the staked point. Design east- ing Display only The entered design Easting. Design northing Display only The entered design Northing. Design height Display only The entered design elevation. Measured easting Display only The Easting measured at the stored point. Measured northing Display only The Northing measured at the stored point. Measured height Display only The height measured at the stored point. Point ID, Stake results page Job Menu - View & edit data 83

Available when the edited point is Class: Measured. For GS points The name of the real-time base station from where the GNSS point was meas- ured, the name of antenna used to measure the point and the baseline values, are shown in display only/observations fields. For TS point It is possible to edit the reflector height. The name of the setup from where the point was measured is shown in a display only field. ☞ Changing the reflector height recalculates the point height. The values for Cut and Fill in Stake results page are also updated. The distance variables Difference in Hz angle, Difference in V angle, Dif- ference in slope distance are shown in a display only field, whenever a measurement has been taken in both faces. More displays the horizontal angle or the azimuth from the point to the instru- ment. For TS points measured with Measure Foresight Listed are the setup ID, the backsight point, the set number and the average measurement values. ☞ Press Sets to include or exclude measured sets in the calculation of a foresight point. Next step Page changes to the next page. Available when the edited point was measured with offsets using TS. Check and change, if required, the entered offset values. When an offset values has been changed, the coordinates for the stored point will be updated. Key Description Store To store the changes. Page To change to another page on this panel. Description of fields Field Option Description Offset left/ right The cross offset of the target point, perpen- dicular to the line of sight. Display only For staked points. Point ID, Obs page Point ID, Offset page 84 Job Menu - View & edit data

Offset in/out The length offset of the target point, in the direction of the line of sight. Display only For staked points. Editable field For measured points. Offset height The height offset of target point. Display only For staked points. Editable field For measured points. Easting Display only The Easting measured at the stored point. Offset applied. Updated, if offset has been edited. Northing Display only The Northing measured at the stored point. Offset applied. Updated, if offset has been edited. Height Display only The height measured at the stored point. Offset applied. Updated, if offset has been edited. Next step Page changes to the next page. Available for GNSS points which were recorded in real-time mode, however not for average or mean points. All fields are display only fields and cannot be edited. The information is obtained from Settings and data coming across with the real-time information and the Ntrip connection. Description of fields Field Option Description Network solution type Single base- line Displayed when Use RTK network is not checked in RTK Rover Settings, RTK net- work page. Point ID, RTK info page Job Menu - View & edit data 85

checked in RTK Rover Settings, RTK net- work page. Network type FKP, VRS, MAX, i-MAX The type of reference network selected in RTK Rover Settings. Refer to "RTK Rover Settings,RTK network page". Nearest If Network type: Nearest is selected in RTK Rover Settings, a singlebase solution is cal- culated and the number of base stations equals 1. RTK data format Display only Refer to "RTK Rover Settings,General page". Number of reference stations in solution Display only • For single-baseline solutions, this num- ber is always 1. • For VRS and i-MAX, this number is always 1 since it is not possible to derive the number of base stations contributing to the VRS or i-MAX corrections from the data format. • For network solutions, this information is derived from the content of the data for- mat. Only RTCM v3 and Leica 4G are able to provide this number. Mountpoint Display only The name of the correction data stream that was selected from the source table received in the TCP/IP port. Available for network RTK with Ntrip. The information is available for all Ntrip con- nections independent from the Network type used. The information is derived from the Connection Settings, either manually defined or selected from the NTRIP Source Table. Point meas- ured inside network Display only Available for network RTK with Ntrip and MAX and data format RTCM v3 or Leica 4G. User ID Display only Available for single baseline RTK, network RTK with/without Ntrip. Next step Page changes to the next page. On this page, multiple elevations which have been stored with a staked point can be edited. Additional multiple elevations can be entered. Refer to "Stake Results,Elevations page" for more information on multiple ele- vations. Point ID, Elevations page 86 Job Menu - View & edit data

Page To change to another page on this panel. Description of fields Field Option Description Elevation Editable field The entered elevation is stored with the point and used to calculate the cut and fill values. Cut/Fill Display only Height of the point being stored – Entered elevation ----------------------------------------- = Cut or fill value (always positive) Examples For cut: Height of the point being stored – Entered elevation ----------------------------------------- Result > 0 598.5672 m – 596.4856 m = 2.0816 m = cut The displayed value is 2.0816 m. For fill: Height of the point being stored – Entered elevation ----------------------------------------- Result < 0 598.5672 m – 599.7826 m = -1.2154 m = fill The displayed value is 1.2154 m. Information Editable field Additional information that must be stored with the elevation. Only the entered Information which also has an entered elevation is stored to the point being stored. Next step Page changes to the next page. Available when the edited point is Class: Measured. The point code and code information can be edited. All point codes in the job can be selected. The description of the code is shown as a display only field. The attributes are shown as display only, editable fields or selectable lists depending on their definition. The attribute values shown depend on the setting in Coding. Suggested attribute values: Last used shows the last used attribute values which are Point ID, Code page Job Menu - View & edit data 87

Default shows the default attribute values for this point code if existing. ☞ It may happen that a point with the same point ID exists in the job. If the codes and/or attribute values of the new and the existing point do not match, a panel opens where they can be corrected. Next step Page changes to the next page. Available when the edited point is Class: Navigated or Class: Measured and no offset point. The comments to be stored with the point can be edited. Next step Page changes to the next page. Available when the edited point is Class: Average. Refer to "7.3.3 Mean Page" for a detailed description. 7.3.3 Mean Page In order to check measurements, the same point can be measured more than once. These measured points are assigned the class Measured. The various meas- ured coordinate triplets for one point can be recorded using the same point ID. If the Duplicate points mode is activated, an average is calculated when more than one measured coordinate triplet is available for the same point ID. The averaged point is given the class Average. It is checked if the deviations of each single point are within the limits configured in Duplicate Points. After averaging, the Mean page becomes available when editing the point and accessible from the Measure app. Available functionality on the Mean page depends on the selected Duplicate points mode. Defining the mode and configuring the limits The mode and the limits are configured in Duplicate Points. Description of modes Mode Description Check the average When more than one measured coordinate triplet is recorded for the same point, the average for the position and the height is computed. Depending on the selected method, the average is computed weighted or arithmetic (no weighting). The class Average is assigned to the averaged point. Point ID, Annots page Point ID, Mean page Description Averaging 88 Job Menu - View & edit data

ured points to the average are computed and dis- played on the Mean page. A check is performed that the differences in position and height, between the averaged point and the point being stored, do not exceed the defined limits. Check the abs diff What is described for Don't check also applies for Absolute differences. Additionally, the absolute difference between two points selected from a list of measured points with the same point ID, is checked to be within the defined limits. Don't check Averaging functionality is turned off. With more than one measured coordinate triplet recorded for the same point, no average for the position and the height is computed. Averaging with position only or height only points Position only points, height only points and points with full coordinate triplets are handled in the averaging. The Mean page can be accessed if When a point is stored with same point ID as existing point: Check the average or When a point is stored with same point ID as existing point: Check the abs diff is configured in Duplicate Points. AND more than one measured coordinate triplet is recorded for the same point using the same point ID. 1. In Job name, Points page, highlight a point to be edited. 2. Edit to access Job name, Mean page. All measured coordinate triplets recorded using the same point ID are shown. Key Description Store To store the changes. Use To change between the options in Use metadata for the highlighted coordinate triplet. To include or exclude this trip- let in or from the calculation of the average. Access step-by-step Point ID, Mean page Job Menu - View & edit data 89

It is possible to edit the point ID and the antenna height without impact on all other classes of the point with the same original name. The coordinates are updated. A change in codes must be an overall change for the average point. Example: One of the measured coordinate triplets has a wrong point ID and should not be included in the average. By editing the point ID, the point is renamed and no longer con- tributes to the average. Delete To delete the highlighted coordinate triplet. The average is recomputed. More To change between time and date of when the point was stored and the 3D coordinate quality. Page To change to another page on this panel. Fn Diffs Available for When a point is stored with same point ID as existing point: Check the abs diff and Yes for the Use metadata for exactly two measurements. To display the absolute coordinate differences when a local coordinate sys- tem is active. Differences exceeding the defined limit are indicated by !. Description of metadata Metadata Description Use The use of a measured coordinate triplet in the averaging. • Auto The coordinate triplet is included in the averaging compu- tation if within the averaging limit defined. • Yes The coordinate triplet is always included in the averaging computation even if it would fall outside the averaging limit defined. • No The coordinate triplet is never included in the averaging computation. • ----- The coordinate triplet cannot be included in the averaging computation. Automatically set by the system. Use changes between the options. Time The time the measured coordinate triplet was stored. Date The date the measured coordinate triplet was stored. The format is as defined in Regional, Time page. dPos The horizontal distance from the measured coordinate triplet to the average. dPos: ----- indicates unavailable information, for example for a height only point. dHt The height distance from the measured coordinate triplet to the average. dHt: ----- indicates unavailable information, for example for a position only point. 90 Job Menu - View & edit data

Available for measured coordinate triplets with Auto or Yes in the Use metadata if When a point is stored with same point ID as existing point: Check the average. Indicates an exceeding of the limits. Next step Store stores the changes. 7.4 Line Management 7.4.1 Overview A line consists of points and can be created/edited. The individual points are measured within any app. All points can be used except auxiliary points. Points can be simultaneously assigned to one or more lines. 7.4.2 Creating a New Line In Job name, Lines page, press New. Key Description Store To store the new line entered and all associated information. Page To change to another page on this panel. Fn Indiv ID or Fn Run For an individual name independent of the ID template or to change back to the next ID from the configured ID template. Description of fields Field Option Description Line ID Editable field The name of the new line. The configured ID template for lines is used. The ID can be changed in the following ways: • To start a new sequence of line IDs, type over the line ID. • For an individual name independent of the ID template Fn Indiv ID. Fn Run changes back to the next ID from the configured ID template. Description Access New Line, General page Job Menu - View & edit data 91

in 3D viewer and Infinity. Colour Selectable list A colour in which the line is displayed. Next step Page changes to the Geometry page. Images are displayed as thumbnail images in a list, together with the image name. Attach one or more images to the line. Key Description Store To store the changes and update the line. New To take an image. Page To change to another page on this panel. Description of metadata Information about the image size and the time and the date of when the image was stored. Next step Page changes to another page on this panel. To create lines with certain codes use quick coding. The job codelist must con- tain quick codes for lines. By typing the quick code a new line is created and immediately stored with that line code and attributes. For the line ID, the line ID template as defined in ID Templates is used. 7.4.3 Editing a Line In Job name, Lines page, press Edit. Key Description Store To store the changes. More To display End time and End date. Page To change to another page on this panel. New Line, Images page Creating lines most efficiently Access Line ID, General page 92 Job Menu - View & edit data

Field Option Description Line ID Editable field The name of the line can be edited. ☞ A line cannot be renamed to an existing line ID. Style Editable field The line style in which lines are represented in 3D viewer and Infinity. Colour Editable field A colour in which the line is displayed. Number of points Display only The number of points contained within the line. Length Display only The sum of the distances between the points in the sequential order in which they are stored for the line. This length can be a horizontal grid distance or a geodetic dis- tance on the WGS 1984 ellipsoid. Start date and Start time Display only The time/date when the line was created. ☞ An edited line retains the creation value for Start time. End date and End time Display only The time/date when the last point was added to the line. This can be different to the time the point was created. The values do not change after deleting the last added point or after editing unless an extra point is added to the line. Next step Page changes to the Geometry page. Listed is the geometry of the nodes that make up the line object. The order corresponds the position of the nodes along the line. Key Description Store To store the changes and update the line. Add To add a node below the highlighted node. Edit To edit the highlighted node, including the linework opera- tion. Delete To remove the highlighted node. Line ID, Geometry page Job Menu - View & edit data 93

Page To change to another page on this panel. Next step IF THEN Allow lines to be coded independ- ently of points is checked in Cod- ing, Code & attributes page Page changes to the Code page. Allow lines to be coded independ- ently of points is not checked in Coding, Code & attributes page Page changes to the Images page. Available when Allow lines to be coded independently of points is checked in Coding, Code & attributes page. Key Description Store To store the changes and update the line. New attrb To add an attribute of type normal and of value type text. Up to twenty attributes can be added. Attributes of type manda- tory or fixed and of value type real or integer must be cre- ated in Infinity. Last Available if a code has been previously used in the job. To select from a list of last used codes. The codes are sorted by time with the most recently used code at the top of the list. Default To recall the default attribute values for the selected code. Page To change to another page on this panel. Description of fields Field Option Description Line ID Editable field The name of the line can be edited. ☞ A line cannot be renamed to an existing line ID. Line code Selectable list or editable field The line code to be stored with the point. Depending on the setting for Allow new codes to be created in Coding, Code & attributes page, the field is a simple list or a selectable list and an editable field at the same time. Code description Display only A description of the code. Next step Page changes to the Images page. Line ID, Code page 94 Job Menu - View & edit data

and an image name. Key Description Store To store the changes and update the line. Sketch To sketch over an image taken with a camera. Delete To delete the highlighted image. Page To change to another page on this panel. Fn Unlink To remove the link from the image to the line. Next step Page changes to another page on this panel. 7.5 Data Log A list of all objects and free codes in the job is displayed in order of time. Access within data management In Job name, Points page, press Fn Log. Access within job management In Job name, General page, press Fn Log. All points, lines and free codes stored within the job are displayed. They are always sorted by time with the most recent record at the top. For lines, the value for Start time is relevant. Key Description OK To close the panel. New To insert a free code below/before the currently highlighted object or record. The functionality of inserting a free code is identical to the functionality of entering a free code during a survey. Edit To edit the highlighted object or free code. The functionality of editing a free code is identical to the functionality of entering a free code during a survey. Refer to "27.4 Free Coding". Delete To delete the highlighted object or free code. Line ID, Images page Description Access step-by-step Data log Job Menu - View & edit data 95

Information about the type of data recorded, the time and the date of when it was stored or for lines when they were created and the codes if stored with any object. 7.6 Point Sorting and Filters 7.6.1 Sorting and Filters for Points and Lines The sort settings define the order of the objects in the job. The filter settings define the objects to be viewed. Two types of filters are available: Type Description Point filter: An active point filter shows selected points in Job name, Points page. Line filter: An active line filter shows selected lines in Job name, Lines page. For information on camera and images refer to "32.4 Image Management". The sort and filter settings are stored in the job. They are remembered after turning off the instrument. When a job becomes active, then the sort and filter settings of this job are saved in the internal memory. If the data storage device is formatted then these last used sort and filter settings are used for the default job. When a new job is created, the sort and filter settings from what was the job are copied to the new job. Changing the job influences the sort and filter settings for the objects. The set- tings are changed to those of the selected job. On the Points or Lines, press Fn Filter to access Sort & Filter. The available fields on this panel depend on the selected setting for Filter to show. Description ☞ ☞ ☞ Access Sort & Filter, Points page 96 Job Menu - View & edit data

panel was accessed. The selected sort and filter settings are applied. Codes Available for Filter to show: Points with certain codes. To define the code filters. Refer to "7.6.2 Point Code Filter". Stake To filter points for the Stake app. Refer to "7.6.3 Stakeout Filter". Page To change to another page on this panel. Description of fields Field Option Description Sort by Point ID - ascending, Point ID - descending, Date - old- est first or Date - new- est first Always available. The method points are sor- ted by. Filter to show Always available. The method the points are filtered by. All Shows all points. Highest point class only Shows points of highest class. Range of point IDs Shows points with point IDs between the entered start and end ID. The points are left aligned and sorted by the first digit. Pt IDs matching wildcard Shows points with point IDs matching the wildcard. Time Shows points which were recorded within a defined time window. Certain point classes only Shows points of the selected class. Pts created by instru- ment Shows points originating from the selected instrument or software program type. Points with certain codes Shows points with selected codes attached. Multiple point ID ranges Available when the Sort & Filter panel was accessed from the Dataset panel. Shows points with point IDs between several entered start and end ID. Start ID Editable field Available for Filter to show: Range of point IDs. The first point to be displayed. Job Menu - View & edit data 97

point IDs. The last point to be displayed. Wildcard Editable field Available for Filter to show: Pt IDs match- ing wildcard. * and ? are supported. * indi- cates an undefined number of unknown characters. ? indicates a single unknown character. Start date Editable field Available for Filter to show: Time. The date of the first point to be displayed. Start time Editable field Available for Filter to show: Time. The time of the first point to be displayed. End date Editable field Available for Filter to show: Time. The date of the last point to be displayed. End time Editable field Available for Filter to show: Time. The time of the last point to be displayed. Control (Ctrl), Adjusted (Adj), Reference (Ref), Measured (Meas), Navigated (Nav), Estimated (Est), None Show or Hide Available for Filter to show: Certain point classes only. Defined classes are shown or hidden. View Available for Filter to show: Certain point classes only. Highest triplet The coordinate triplets of the highest class are shown. All triplets All classes for one coordinate triplet are shown. Instrument All, TS, GS, Office, Level, Con- troller, Third party SW or Unknown Available for Filter to show: Pts created by instrument. Points originating from this instrument type are shown. List of ranges Editable field Available for Filter to show: Multiple point ID ranges. Enter the first and the last point of a range to be displayed. Single point entry is valid. • ,: Separates the ranges. • -: Separates the first and the last point of a range Example: 1-20,25,30-40 98 Job Menu - View & edit data

Key Description OK To close the panel and return to the panel from where this panel was accessed. The selected sort and filter settings are applied. Page To change to another page on this panel. Description of fields Field Option Description Sort by Line ID - ascending, Line ID - descending, Start point - oldest first, Start point - newest first, End point - old- est first, End point - newest first Always available. The method the lines are sorted by. Next step OK closes the panel. 7.6.2 Point Code Filter 1. In Sort & Filter select Filter to show: Points with certain codes. 2. Codes to access Point Code Filter. Sort & Filter, Lines page Access step-by-step Job Menu - View & edit data 99

ter. Point codes are sorted according to the settings in Sort Codes. Key Description OK To close the panel and return to the panel from where this panel was accessed. Group To activate and deactivate code groups. Accesses Code Groups. Any code group that has been previously deactiva- ted are displayed as deactivated here. Codes belonging to a deactivated code group are not displayed in Point Code Fil- ter. Use To activate and deactivate the filter for the highlighted code. None or All To deactivate or activate all point codes. Fn Sort To define the order of the codes. Accesses Sort Codes. 7.6.3 Stakeout Filter The settings on this panel define a filter for the Stake app. The Stake filter can be applied to show points which are already staked or points that are still to be staked. The stakeout filter acts in addition to any other filter set in Sort & Filter. For example, points still to be staked out with a particular code can be filtered. In Sort & Filter, Points page, press Stake to access Stakeout Filter. Point Code Filter Description ☞ Access Stakeout Filter 100 Job Menu - View & edit data