Lockly DEADBOLT EDITION PGD1128 Installation Manual

Avoid touching with bare hands. For best practices, (1) ground yourself by (a) touching a metal surface to discharge any ESD you might have; (b) changing clothes if you are sparky; and (2) avoid touching the internal pins. C A U T I O N

INSTALLATION OVERVIEW AND PARTS LIST A B S U T C D G I H 2x J K 4x L N P Q E E F 2x Parts List Labeled As Description A Keys B Exterior Assembly C Exterior D Mounting Plate E Adhesive F PM5×60mm Screw G Interior Assembly H PM4*12MM Screw I Battery Cover J Deadbolt K KA4*20MM Screw L Strike Plate N Dust Box P Wired Sensor Q R S T Sensor Magnet Vision Connect LAN Cable Power Plug U TF Card V Activation Card R Adhesive TAPE Adhesive TAPE V SCAN & SAVE LOCK SERIAL ACTIVATION CODE PGDXXXXXXXXX XXXXXXXX

1.1: To complete installation, you would need the following: 1.2: Prepare door and remove existing lock. If necessary, use provided Installation Template to prepare door. Phillips Screwdriver Flathead Screwdriver Ruler 1-⅜" (35mm) to 2" (50mm) 1" (25mm) 2-⅜" (60mm) or 2-¾" (70mm) 2-⅛" (54mm)

adjust as shown below: 2.1.1 Wear gloves during adjustment to prevent pinching your hands II. Hold the metal plate (c) and twist the deadbolt body (d) clockwise till it snaps to 2-3/8" III. To return to default status, while the deadbolt (b) is extended, hold the metal plate (c) and twist the dead- bolt body (d) counter-clock- wise till it snaps to 2-3/4" (b) (a) （c） （d） （c） （d） I. Push the crank (a) to extend the deadbolt (b) Deadbolt at 2-3/4" (70mm) (default shipping status) STEP 2. ADJUST DEADBOLT AND INSTALL

flat head screwdriver on the slit hole or by pushing the crank towards the metal face plate. 2.3 Insert the Deadbolt to the edge door hole, make sure that its right side up and the slit hole is in vertical position, then secure with 2 screws (K) K(2X) STEP 2. ADJUST DEADBOLT AND INSTALL 1 2

3.1: Check the Exterior Assembly alignment to your door hole and deadbolt, before you peel off the cover of the adhesive strip. 3.3: Place the exterior assembly on the door by inserting the torque blade on a vertical position to the deadbolt slit hole and guide the cable under the deadbolt. Secure with the adhesive strips. 3.2: Before placing the exterior assembly on the door, make sure the torque blade is in vertical position and the deadbolt is extended. EXTERIOR VIEW (1) Vertical When installing the exterior assembly, make sure the deadbolt is fully extended and the slit hole is vertically positioned on the bottom, the torque blade should be inserted in a vertical position.

4.1: Check the mounting plate alignment to your door hole before you peel of the cover off the adhesive strip. 4.3: Without using any tools, insert 2 screws (F) on the side of the torque blade. By using hand carefully, turn the screws clockwise to catch the thread, then counter clockwise to make sure they are not cross threaded and turns smoothly. Make five turns before using a screw driver to tighten the screws until the mounting plate is securely placed to the door. 4.4: After securing the mounting plate, use the physical key and try to unlock/lock to check if the deadbolt is moving and not stuck. Do not forget to take out the key before proceeding to next steps. 4.2: Place the mounting plate on the interior side of the door. Guide the cable to the opening ear on the side of mounting plate and make sure the torque blade is at the center of the mounting plate. F(2X)

Make sure you install the Door Sensors indoors on a clean and dry surface. Gently wipe the surface of your door and door frame before installing. Part P - Wired Sensor Part Q - Sensor Magnet * The Door Sensors provide the ability to verify if door is securely closed. It also sends push notifications to your phone whenever your door opens. If you intend to use Amazon Alexa or Google Assistant, ensure the door sensors are properly installed to acknowledge your voice commands and to have the correct responses. IMPORTANT: Gap must be less than 3/4” when installed. When installed on your door, the distance between the wired sensor and sensor magnet must be less than 3/4” in order for the sensor to work. When door frame is higher than the door panel, add included foam pads at the bottom of the wired sensor to reduce its distance from the sensor magnet at the bottom of the wired door sensor. STEP 5. PREPARING DOOR SENSORS FOR INSTALLATION > Do not install the door sensors yet. You will install the sensors on STEP 8

sure the arrow of the wired sensor (P) is placed next to the arrow of the sensor magnet (Q) as close as possible. If needed add Foam Pads to level P & Q as much as possible. 2-3/4" (70mm) 2-3/8" (60mm) < 3/4" (< 20mm) EVA STEP 5. PREPARING DOOR SENSORS FOR INSTALLATION P Q

pre-installed wired door sensor for right swing doors with 2 ¾" (70mm) backset*. Discard the excess part (e) for doors with 2 ⅜" (60mm) backset as shown below: 5.2 For left swing doors, re-route the door sensor wire through the side channel. Pull the foam pad (f) then re-insert to secure the wire. Discard the excess part (e) for doors with 2 ⅜" (60mm) backset as shown below: *Backset - measure the distance of the door edge to the center of the door hole. DO NOT INSTALL THE SENSORS YET > Pull Insert P P f STEP 5. PREPARING DOOR SENSORS FOR INSTALLATION 3 2 1 e

cable, make sure to press the snap to release the plug before carefully pulling it out. Do not force to pull the plug as this may result to lose connection and damaged the lock. 6.1 From the cable coming from the external assembly (PART B), plug the small cable con- nector x to y and screw tightly as shown: STEP 6. INSTALLING THE INTERIOR ASSEMBLY (G) 6.2 Plug the larger cable that is coming through the door into the Interior (PART G) lock. Match the red side of the plug with the red on the socket. Ensure it is inserted tightly. Tuck the cable under the hook and route it to the right as shown. (x) (y) Connect and Screw Do not touch the pins inside * Call our Customer Service Hotline (669) 500-8835, if the pins are not centered or bent.

6.3 Before placing the interior assembly to the mounting plate, ensure the thumb turn is vertical. 6.4 Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft. 6.5 Secure the interior assembly with 2 screws (H) Torque Blade Thumb turn shaft Push the thumb turn shaft into the torque blade. MAKE SURE IT IS IN THE VERTICAL POSITION

extended, place the ribbon inside the compartment and insert only 3 batteries at the bottom layer with correct polarities. Ensure the bolt is FULLY EXTENDED 7.2 Press and hold the program button before inserting the 4th battery. The lock will automatically do a self-check. RELEASE the program button. The lock information will be shown on the touchscreen. The self-check process is very important to ensure the installation is done properly. After the lock finished the self-check, do the 2-steps below to ensure your lock is properly installed: STEP 7. INSTALLING BATTERIES 1. Manually lock and unlock your door by using the thumb turn and the key to make sure the deadbolt moves smoothly. If you feel that there is a tight tension while you are turning, it means that the lock may have not been installed straight. Go back to Step 2 and re-install the lock. IMPORTANT: If your lock is not properly installed, it will open and close repeatedly at times and/ or it will reduce battery life. 7.3: After you checked that the lock manually lock and unlock properly and deadbolt moves smoothly, continue to install the last 4 batteries on the top layer of the battery compartment. 2. Swipe your hand across the touchscreen keypad, the lock will close. If the deadbolt bounces and unlocks automatically, it means that your lock was installed incorrectly. Go back Step 2 to make sure your lock was installed with the (a) deadbolt extended and (b) the torque blade was inserted vertically while the deadbolt was extended. 7.4: Install the Battery Cover (I) and secure with screw. PRESS & HOLD 1 2 3 4 5 6 7 8 5 6 7 8

adjust the position of the sensor magnet using provided foam pads to ensure the LOCKLY® logo blinks red when door opens or closes. 2-3/4" 70mm 2-3/8" 60mm STEP 8. INSTALLING THE DOORS SENSOR 8.1 Peel off the paper layer of the adhesives from the back of the wired sensor (P). 8.2 Position the wired sensor (P) to the edge of the door. Attach and secure with the adhesives. 8.3 Retract the deadbolt by turning the thumb turn, then close the door. Before you peel off the paper layer of the adhesives from the sensor magnet (Q), align the arrow with the wired sensor (P). Install Q on to door frame. Make sure you have prepared the door sensors for installation according to Step 5

Install the door strike to your door frame and proceed to the last step of installation of your new lock. You may use our supplied door strike or use your existing door strike as long as the deadbolt moves smoothly in and out of the door strike. As there are many types of doors, you may need to make slight adjustments so the deadbolt moves smoothly. If anything is rubbing against the deadbolt when locking and unlocking, you may experience a warning sound (rapid beeping) indicating that the lock is experiencing misalignment or something is blocking the deadbolt. L K(2X) N STEP 9: INSTALLING THE DOOR STRIKE

To enable video doorbell, add Live Monitoring and voice control with Google Assistant or Amazon Alexa, you will need to setup the Vision Connect included in the box. STEP 10. VISION CONNECT SETUP IMPORTANT: Vision Connect contains important video recording on the TF card, ensure your selected location is discreet or a secured area to protect the privacy of your video recording . LAN LED INDICATOR Power Plug TF Card RESET

router to directly plug the LAN cable that comes with Lockly Vision™ The selected location is suggested to be less than <50 feet away from Lockly Vision™ NOTE: Distance between Lockly® to Vision Connect may vary according to your home. If you're having issues with the setup, we are here to help. Call our customer care team: (669) 500 8835 or visit http://lockly.com/help for suggested troubleshooting. STEP 10. VISION CONNECT HUB SETUP 50 Feet (15 meters) Distance Between Lockly Vision™ You Vision Connect Wi-Fi Router Using an iOS or Android™ Device with Bluetooth & Wi-Fi enabled >3 feet (1 meter) above the ground IMPORTANT: Lockly Vision™ is a 2.4Ghz device. To optimize your video streaming connect your other Wi-Fi devices to the 5.8Ghz network.

with Vision Connect is properly inserted. TF card is included 10.3： Ensure to plug the LAN cable to the nearest Wi-Fi router to Lockly Vision™. 1ft cable (S) Included 10.4： Plug the USB adapter to a wall socket. STEP 10. VISION CONNECT HUB SETUP 10.5： After connecting to power, wait for 2 minutes for Vision Connect to self calibrate. Once the LEDs turned RED and blinking yellow, Vision is ready to connect. IMPORTANT: Refer to Vision Connect Troubleshooting Guide if the LEDs do not meet the described conditions.

Solid Red ON During Setup Power ON/ Successfully paired Network Connected Pairing | Network NOT yet Connected Pairing Unsuccessful Router or LAN cable issue NO Network Connection Resetting Yellow Slow Blinking Red Slow Blinking Red Fast Blinking Yellow OFF Blinking from Red to Blue , Then OFF Blue Slow Blinking Update in Progress* Update Successful Update Failed Blue ON Blinking from Red to Blue After you plug in the LAN cable and Power adapter, and wait for 2mins for Vision Connect to self calibrate. During Firmware Update Vision Connect Troubleshooting Guide LED INDICATOR STATUS * Power interruption during firmware update may damage the Vision Connect hub. Do not interrupt or turn the power off while firmware update is in progress.

11.2： After you have you successfully registered an account, you can proceed to Add New Device and follow the step by step on screen instructions. 11.3： When prompted, make sure you scan the small QR code located on the side or bottom of the Vision Connect to pair hub with lock. Scan or visit Lockly.com/app You have completed the Lockly Vision™ and Vision Connect installation and setup. Now you’re ready to pair your lock. 11.1：Download the Lockly® App and register an account. IMPORTANT REMINDERS: 1.. Remember to register for warrant 2.. Allow your mobile phone to receive push notification 3.. Send in-app feedback if you encountered any issu while using the App. 4.. Ensure your Lockly® App has the most updat firmware. For more info, visit: http://www.support.lockly.com/faq/firmware-update/ Scan QR code located on hub

status or remotely lock and unlock your door with your voice using Amazon Alexa or Google Assistant. Google, Android and Google Play are trademarks of Google LLC. For a full list of commands, help videos or to troubleshoot your Secure Link Wi-Fi Hub visit us at https://lockly.com/help To setup your lock to work with either voice assistant, download the Amazon Alexa or Google Home App and add a new skill with Amazon Alexa or the Action for Google Assistant. Add the “Lockly® ” Skill for Alexa or the Action for Google Assistant then follow on screen instructions to finish setup.

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement Vision Connect complies with FCC radiation exposure limits set forth for an uncontrolled environ- ment. It should be installed and operated with minimum distance 20cm between the radiator & your body. IC WARNING This device contains license-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de lanorme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps. WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Wamings.ca.gov.