Telkom EasiTouch 200 Manual 

2. Maintenance ...................................................... 3. Installation precautions ...................................... 4. Caution .............................................................. 5. User controls ...................................................... 6. Setting up ........................................................... 6.1 Important information ......................................... 6.2 Contents of package .......................................... 6.3 Connecting the handset and line cord ............... 6.4 Mounting the phone ........................................... 7. Telephone Operations ....................................... 7.1 Dialing a number ................................................ 7.2 Receiving incoming calls ................................... 7.3 Handset receiver volume control ....................... 7.4 Setting the ringer melody and melody volume .. 7.5 Using Redial ...................................................... 7.6 Recall ................................................................. 7.7 Using Mute ......................................................... 7.8 Using Pause ...................................................... 8. Storing a number ............................................... 8.1 M1-M2 and VIP memory buttons ....................... 8.2 Quickdial memory buttons ................................. 9. Batteries ............................................................. 10. Troubleshooting ................................................. 11. Service Enquiries ............................................... 2 2 2 2 3 4 4 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 10 11 Contents 1

Read the instruction manual carefully before connecting and operating your telephone. The telephone has no user serviceable components and service should therefore be referred to authorized service centers only. 2. Maintenance · Only use a damp cloth to clean the cabinet. A mild soap will help to remove grease or oil. Never use polish, solvents, abrasives or strong detergents since these can damage the telephone. · Your phone should be situated away from heat sources such as radiators, heaters, stoves or any other appliance that produces heat. 3. Installation precautions · Never install telephone wiring during a lightning storm. · Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Caution To reduce the risk of fire or injury read and follow this instruction: · Never push objects of any kind into this telephone as they can touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. 2

3. M1/M2 one-touch buttons 4. Receiver volume button 5. Handset hook 6. Hook switch 7. Mute indicator 8. In use indicator 9. VIP one-touch button 10. Recall button 11. Pause button 12. Redial button 13. Store / Mute button 14. Line jack 5. User controls 3

instructions at the beginning of this manual. 6.2 Contents of package The package contains: Telephone, one handset with handset cord, one telephone line cord, one desktop bracket and this instruction manual. 6.3 Connecting the handset and line cord 1. Plug one end of the telephone line cord into the socket at the back of the telephone. Plug the other end of the telephone line cord into the wall outlet. 2. Plug one end of the coil cord into the socket on the left side of the telephone. Plug the other end of the coil cord into the handset socket. 6.4 Mounting the phone You can mount your telephone directly against a wall, or place it on a shelf, desk or table. The unit can be mounted to any wall surface using two self- tapping screws (not supplied). 1. Drill two holes in the wall 67mm horizontally apart. 4

1. Lift the handset and wait for dial tone. The “In Use” LED lights. 2. Press the keypad for the telephone number you wish to dial. 3. When you complete your call, replace the handset. 7.2 Receiving incoming calls When you receive a call, the phone rings. To answer the call, proceed as follows: 1. Lift the handset. 2. To end the call, replace the handset. 2. Insert wall plugs into each hole. 3. Then thread a screw into each hole, letting the heads extend about 5mm from the wall. Position the telephone over the two screw heads and push downward. 4. Slide out the handset hook on the telephone, rotate it 180 and replace it. The handset will rest on the hook when wall mounted. ° 5

In the off-hook state, you can adjust the speaker volume by using the VOL button. You can select between two volume levels (HI or LOW). 7.4 Setting the ringer melody and melody volume You can select between 3 different ring melodies and 3 different volume levels for each melody. See table below for details. 1. Lift the handset. 2. Press the button. 3. Press the # key. 4. Press the numeric key 0 to 9 to set the ringer type and volume. (see table below) 5. Replace the handset. If setting 0 is selected, the ring signal will be turned off until the handset is lifted again. After that, the ring signal reverts to the previous setting. 6 Melody 2 Melody 3 7 4 1 2 5 8 9 6 3 Low Mid High Melody 1 / 7.5 Using Redial To redial the last number dialed, proceed as follows: 1. Lift the handset. 2. Press the RD button.

subscribe to this service you can use this feature to put a call on hold and answer another call on the same line by pressing the R button. NOTICE: If you do not have CallWaiting, pressing the R button might disconnect the current call. NOTICE: A subscription is required to use the CallWaiting services. Please call 10219 to subscribe to this service. 7.7 Using Mute press the To talk to someone on your end of the phone without the caller hearing your conversation, button and the “Mute” indicator will flash. Press the button again to resume your conversation. 7.8 Using Pause In some telephone systems, you must dial an access code (9, for example) and wait for a second dial tone before dialing an outside number. When you store a number in memory, you can have your telephone pause anywhere during the dialing sequence. Simply press the P button at the desired location to insert a 3.6 second pause. / /

You can store up to 13 numbers in your phone’s memory for quick and easy dialing. You can store 3 numbers in the one- touch memory and 10 numbers in the quickdial memory. The maximum stored number length is 32 digits. 8.1 M1-M2 and VIP memory buttons 1. Lift the handset and press the button. 2. Press the desired memory location (M1, M2 or VIP) 3. Enter the desired number from the keypad. Press the button to store the number in the one-touch memory. Replace the handset. 4. The number will automatically be stored. To dial a number from the one-touch memory, proceed as follows: 1. Lift the handset. 2. Press the relevant one-touch button (M1, M2 or VIP). 3. The number will then automatically be dialed. 8.2 Quickdial memory buttons 1. Lift the handset and press the button. 2. Press the AUTO button. Press the desired memory location (0-9) / / /

button to store the number in the quickdial memory. Replace the handset. 4. The number will automatically be stored. To dial a number from the quickdial memory, proceed as follows: 1. Lift the handset. 2. Press the AUTO button followed by the relevant location (0-9). 3. The number will then automatically be dialed. / 9. Batteries This product is powered by the telephone line and does not need or require batteries.