Nyrius NY-GS10 Manual 

NY-GS10 NYRIUS.COM/RESOURCES IR Remote Output (for Infrared Extender) Power Switch Channel Selector IR Frequency Selector (A - 38KHz, B - 56KHz) Power Input RCA Inputs RCA Outputs 1. 2. 3. 4. 5. 6. 7. 4 3 2 1 REMOTE CH A B IR TRANSMITTER VIDEO IN AUDIO IN LEFT RIGHT DC 12V 4 3 2 1 RECEIVER VIDEO OUT AUDIO OUT LEFT RIGHT DC 12V WHAT’S INCLUDED BUTTONS & CONNECTIONS FIRST TIME SETUP Transmitter Receiver RCA Cables IR Extender Power Adapters Connect power to Receiver. Connect Receiver to RCA inputs on TV with RCA cable. Some TVs may have Component Inputs that also function as RCA inputs. Check your TV’s manual for more information on connecting an RCA cable. RECEIVER all-guide s.com

Connect power to Transmitter. Connect Transmitter to RCA output on source device with RCA cable. Examples of a source device include Cable Boxes, Satellite Receivers, DVD Players, and VCRs. 2 TRANSMITTER DEVICE Set the Channel Selection switch on both the Transmitter and the Receiver to the same channel. Set the Power Switch on both to the ON position. Note: If signal is not clear or if devices are not connecting change the channel on both the Transmitter and the Receiver. 3 TRANSMITTER Power Channel Selection Connect IR Emitter to Transmitter and place 5-10 cm in front of source device. Test remote control by pointing it at the Receiver, an LED should flash on the Receiver. If there is no response, change the Remote Frequency switch and test again. 4 RECEIVER

NY-GS10 NYRIUS.COM/RESOURCES FIRST TIME SETUP CONTD. Adjust both antennas and ensure they are oriented towards each other. 5 TRANSMITTER RECEIVER TROUBLESHOOTING What If They Don’t Connect? Please ensure that the transmitter and receiver are within 250 feet of each other. Although the signal can pass through walls and floors, line of sight is recommended as obstacles can reduce the transmission distance. Ensure that the underside (4 squares) portion on the antennas are facing each other. Confirm that both power switches are set to the ON position and that the channel selection switches are set to the same number. Test each channel to improve signal strength and avoid interference. All wireless devices may be subject to interference, which may result in a loss of signal, or intermittent signal. To correct interference issues we recommend adjusting the antennas or the position of the transmitter and receiver by moving them away from sources of interference. Sources of interference can be devices such as cordless phones, wireless routers and microwaves. Why Is My Video Black and White? If the image transmits in Black & White, the video cable may be connected to a Component Video input: these are Red, Blue, and Green. Some TVs will have a Yellow RCA connection built into the Green Component connection. It may be necessary to change your TV settings to enable the Video input option. To find information that is specific to your TV, please check your TV’s user manual. How Can I Transmit To Multiple TVs? The NY-GS10 does support multiple receivers. If you wish to transmit to a second TV additional receivers are available www.nyrius.com.

purchase date against defects in workmanship and materials. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equip- ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Keep small parts away from children. IC STATEMENT / DÉCLARATION IC This Class B digital apparatus complies with ICES-003. / Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS 210 standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR 210 d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisa- teur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en comprom- ettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Thank you for your purchase of this Nyrius® product. We hope you enjoy your experience. Questions? Give us a chance to help, we’re just a click away Don’t forget to register your product with us! Nyrius.com/registration Nyrius.com/resources Nyrius.com/support Nyrius.com/videos Nyrius.com/contact