Quoizel HC8407IB Assembly Instruction Sheet

1of2 Assembly Instruction Sheet #IS-HC8407IB_R1 For Style HC8407IB 2016 QuoizelInc. Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. A Crossbar Assembly x 1 Please go to for product cleaning tips. Go to the selection. (1)A21 Medium Base bulb 150W Maximum. 20-30 minutes Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts. www.quoizel.com Care + Maintenance Light Source: EstimatedAssembly Time: Preparation: Fixture can only be mounted in the direction indicated on page 2. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. C Fixture Body x 1 ReleasedDate:2016-12-08 Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com B Alternate Mounting screw x 2 STEP 1 Remove Paper - A. Remove paper inside of the cage and Fixture Body (C). STEP 2 Installing the Crossbar Assembly - A. Pass the supply wires through the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure the Crossbar Assembly (A) with Outlet Box Screws (not included). Tighten until snug Note: Use the Alternate Shorter Mounting Screw (B) if your installation requires a shorter mounting screw. . Supply Wires with Ground Wire Outlet Box Screws (not included) Outlet Box A Figure 2 Mounting Screw or Alternate Short Mounting Screw STEP 3 Test Fit the Backplate to the Crossbar Assembly - A. Remove the mounting balls from the Crossbar Assembly (A). Place the backplate and Fixture Body (C) onto the Crossbar Assembly (A) and secure with mounting balls. Note: The backplate and Fixture Body (C) should be snug against the wall and held tight with the mounting balls. If it is not, adjust the length of the mounting screw or alternate short mounting screw on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws or alternate short mounting screws C Mounting Ball A Backplate Hex Nut and Lock Washer Figure 3 Mounting Screw or Alternate Short Mounting Screw Cage Figure 1 Paper C STEP 4 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. Figure 4 White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box Ground wire from fixture Bare, or Green Ground wire from outlet box OR Ground wire from fixture Green Ground Screw on the Crossbar in or out of the crossbar until the correct length is achieved. Once the backplate and Fixture Body (C) is secure, remove the mounting ball and Fixture Body (C) and proceed to Step 4.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com STEP 5 Install the Fixture Body - A. Position the backplate and Fixture Body (C) onto the Crossbar Assembly (A). Place the holes in the backplate over the mounting screws or alternate short mounting screws. Secure the Fixture Body by using the mounting balls and hand tighten the mounting balls until snug. Figure 6 STEP 6 - Install the Bulb and Apply Silicone Sealer A. Insert the bulb onto socket and screw snugly into place. B. Make sure the exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, caulk over top of backplate and down both sides. Do not caulk the bottom of Socket Bulb (not Supplied) Exterior Grade Caulk Backplate Exterior Grade Caulk the fixture backplate to ensure proper moisture drainage. Your fixture is now assembled and ready to use. Enjoy! HC8407IB FINISH: IMPERIAL BRONZE 7" 7" 10" 7.75” 4.5" NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" Fixture can only be mounted in the direction indicated ReleasedDate:2016-12-08 Figure 5 C Mounting Ball A Backplate Mounting Screw or Alternate Short Mounting Screw