Pyle PUSBMIC43 Operation & User’s Manual

belt pack transmitter with headset MIC and lapel MIC, this UHF wireless USB microphone brings the convenience of wireless to your karaoke and recordings. It's the ideal wireless system for karaoke, podcasting, YouTube performances, voice over projects and much more. The belt pack transmitter together with headset MIC or lapel MIC provides exceptional sound reproduction for spoken word presentations, as well as singing applications and more. It offers over 60' of wireless range (environment dependent), operating in UHF 500-980MHz high frequency band. The wireless receiver is USB powered and features plug- and-play operation with no driver installation required. Simply connect the receiver directly to your computer via USB and start singing and recording. FEATURES • UHF 500-980MHz high band wireless system • Wireless receiver built into a USB stick • Belt pack transmitter with headset MIC and lapel MIC • Transmitter operates on two AA batteries (included) • 60' operating range (environment dependent) • Plug-and-Play operation with no driver installation required

more. • Record wirelessly to your favorite DAW or voice recognition software on your Mac/PC. USING BELT PACK TRANSMITTER 1. Antenna 2. Power ON/OFF Switch 3. MIC in jack 4. Power / low battery Indicator 5. Battery Compartment / Cover 6. Lapel MIC 7. Headset MIC OPERATION 1. Open battery cover. Install the provided 2pcs 1.5V AA batteries and then close the cover. Pay attention to the correct polarity. 2. Push power switch to ON position, power indicator lights green indicating that the transmitter has sufficient power. If the power indicator starts to flash, it indicates that the battery has insufficient power and should be changed. If the power indicator does not light at all

you should change the battery. 3. Now receiver RF indicator should light. (Please confirm the frequency of microphone same as that of receiver before operation). 4. If the microphone is not going to be used for any length of time, push the power switch to OFF position and remove the battery. USING WIRELESS RECEIVER 1. USB connector: Plug into a computer or Mp3 player, USB port or 5V power adapter to get power. 2. Line Out: to connect to external speakers. 3. RF indicator: When the transmitter is powered on, this indicator will light red displaying normal reception. CONNECTION 1 (Computer Karaoke) Plug the USB connector of wireless USB receiver into a USB port of a computer. Connect the external speakers to phone out of the USB

transmitter to start singing a karaoke song! Note: 1. With this connection, please set playing device (audio output device) of your computer to “USB Audio Device”. 2. With this connection, the receiver will receive vocal signals from the transmitter and pass vocal signals directly to LINE OUT to be mixed with music signal from the computer via USB connector. Recording is not allowed in this mode. CONNECTION 2 (Computer Recording) Plug USB connector of wireless USB receiver into USB port on a computer. Turn on the belt pack transmitter and use audio software on your computer to sing and/or record. Note: 1. In Recording Mode please set the recording device (audio input device) of your computer to “USB Audio Device”.

external speaker to line out of USB receiver. If you want to play a recorded file connect headphone or external speaker to your computer phone out. CONNECTION 3 (Working as a Wireless Microphone system) Plug USB connector of wireless USB receiver into USB port of Mp3 player in your active speaker system. Using supplied 3.5/3.5 audio cable connect the line out of the wireless USB receiver to MIC IN or LINE IN of your active speaker. This wireless USB receiver can also be powered by external 5V power adapter (not supplied) to be used as a wireless microphone system.

Frequency Signal System: UHF Wireless Wireless Operating Range: Up to 60’ Ft. Frequency Response: 100Hz-12kHz Dynamic Range: >80dB Receiver Output: >300mV Output Impedance: 1KΩ Battery Operated Belt Pack Transmitter, Requires (2) 'AA' Batteries Belt Pack Size (L x W x H): 2.5’’ x 1.0’’ x 3.4’’ USB Receiver Size (L x W x H): 1.0’’ x 0.5’’ x 2.8’’ Weight: 0.37 lbs.