Comfortex Simplicity Installation & Care Instructions

- Measuring tape - Power drill, drill bits - 1⁄4” Hex head and/or Phillips driver bit - Pencil GETTING STARTED 1 1⁄4” Hex Head Bracket Screw Head rail Extension and Sidemount Bracket (optional) Spacer Block (optional) Additional fasteners other than those sent with your shade may be required depending on the mounting surface. Wallboard and plaster require the use of anchors such as expansion or toggle bolts. Brick, tile or stone need special plugs and drill bits. Remember to always pre-drill holes in wood to avoid splitting. Mounting Bracket Hold Down Bracket (optional) STEP 1: BRACKET INSTALLATION PN: CS5402 PN: 20201012 PN: CS1000 PN: CS2000 Shades are shipped with the required number of brackets for proper installation. End brackets should be located approximately 3” from either end. Depending on the width of the shade, additional brackets may be necessary, evenly spaced between the two end brackets. If mounting the battery wand to the head rail, bracket positions may need to be adjusted to accomodate the battery wand. You must have at least 19” between bracket centerlines to fit the battery wand. Using the installation bracket as a template, measure to the edge of the bracket and mark the hole locations with a pencil for drilling. Brackets must be in line and level. Shim brackets on inside mounts if necessary. The head rail must be level for the shade to operate properly. Shade Width # of Brackets Up to 40” 2 >40” - 72” 3 >72”- 84” 4 >84” and up 5 INSIDE MOUNT The minimum mounting depth for an inside mount is 1”. A minimum of 3 3⁄4” is needed to fully recess the shade. Make sure the brackets are level and aligned. Attach using two screws. Inside Mount Shallow Mount - Minimum 1” surface Flush Mount - Minimum 3 3⁄4” surface 1” Wall Mount Battery Wand Clip head rail Mount Battery Wand Clip Mounting Brackets for Shades without head rail PN: CS5171 PN: CS5492 PN: CS1101 PN: CS5002(W or BLK) CS5008 (W or BLK) CS5529 CS5530 Depends on size of shade SHADES WITH HEAD RAIL 3” 3” 19” min. between bracket center lines to mount battery wand to head rail

Optional extension brackets are used to project the back of the shade up to 2 1⁄2” from the mounting surface. Attach the mounting bracket to the extension bracket with the nut and bolt provided. SIDE MOUNT (OPTIONAL) Measure from window sill up to desired mounting position on each side of the window frame. Mark position. Mount side mount brackets on each side of window frame as shown. Make sure to confirm the head rail will sit perfectly level. Once side mount brackets are installed and properly positioned, attach the mounting brackets using the nuts and bolts provided. Side Mount Minimum 2” surface Outside Mount with Extension Brackets Minimum 2” surface SPACER BLOCKS (OPTIONAL) Each spacer block projects brackets 3⁄8” away from mounting surface. Make sure the brackets are level and aligned. Attach using two screws. Screws should be long enough to secure the bracket to the mounting surface. Outside Mount with Spacer Blocks 2” 2 1⁄2” OUTSIDE MOUNT The minimum mounting height for outside mounted shades is 1”. Make sure the brackets are level and aligned. Attach using two screws. Outside Mount Minimum 1” surface 1” 2”

Foot T-Hook The installation brackets are always mounted so that the inner surfaces face each other. Brackets must be in line and level. Shim brackets on inside mounts if necessary. The head rail must be level for the shade to operate properly. SHADES WITH NO HEAD RAIL STEP 2: BATTERY WAND INSTALLATION (IF TRANSFORMER SKIP TO STEP 3) WALL MOUNT Attach the wand clips in the desired location with the screws provided. Before mounting the wand, make sure that the wand and excess wire will not interfere with the operation of the shade. Extension wires are available if needed. Press the wand into the clips. Please Note: Be sure battery wire will reach motor plug. HEAD RAIL MOUNT Attach the wand clips to the back of the head rail as shown. Important: Position the clip so that the battery wand will be between mounting brackets. Before mounting the wand, make sure that the wand and excess wire will not interfere with the operation of the shade. Extension wires are available if needed. Press the wand into the clip. Please Note: Be sure battery wire will reach motor plug. Inside Mount Minimum 1 1⁄2” surface Outside Mount Minimum 1 1⁄2” surface 1 1⁄2” 1 1⁄2”

Push the rail back until it is fully engaged Center the shade in the window opening and push the head rail into the mounting brackets as shown. Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the fabric. Insert the foot of the motor-side bracket into the slotted center hole of the motor end of the fabric roll. The wire should be positioned so that it goes up on an inside mount or back on an outside mount. This will provide easy access to the setting button. Set the post of the idler end into the V of the support bracket. Rotate the T-hook on the support bracket to lock in the post and secure the fabric roll. Nub Support Bracket Fig.15 Idler Post V slot SHADES WITH HEAD RAIL SHADES WITH NO HEAD RAIL

the wire behind the shade and along the window casing as required. Plug the transformer into an electrical outlet. If the wire is not long enough to reach, optional 48” extension wires are available. BATTERY WAND Plug the battery wand wire into the motor wire. STEP 4: CONNECT POWER SOURCE - BATTERY WAND/TRANSFORMER The factory has set your shade to the channel that was specified at the time of order. If no channel was specified, the shade was set to operate on channel 1 and “all”. Select the desired channel with the CHANNEL buttons. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit the remote will control all 5 channels at once. Tapping the UP or DOWN buttons for less than 2 seconds will move the shade in short steps. Holding the UP or DOWN buttons down for more than 2 seconds before releasing, will operate the shade in the faster standard speed. Press the UP or DOWN buttons to raise or lower the shade. Press the STOP button to stop the shade anywhere along the travel. 1 2 3 4 5 Channel Display Up Stop Down Channel + Channel -

The lower and upper limits have been set at the factory. If you need to make adjustments to the limits, follow the instructions below. Please Note: When clearing the factory set limits, both the upper and lower limits will need to be reset. Use the CHANNEL buttons to select the channel for the shade that needs to be adjusted. Then follow the directions below. If only adjusting one shade on a channel, unplug the other shades. A. Set Lower Limit B. Set Upper Limit 1 2 3 4 5 Channel Display Up Stop Down Channel + Channel - C L Confirm Limit OPERATION RESULT 1 Hold LIMIT button down The motor begins to jog 2 Release the button after jogging stops The motor is ready for limit setting 3 Press DOWN button The motor will go down continuously 4 When the motor is close to the desired lower limit, press STOP button on the remote The motor stops running 5 Press either the UP or DOWN button The motor runs step by step to adjust lower limit accurately 6 Confirm the setting by pressing the CONFIRM button on the remote The motor jogs and the lower setting is completed OPERATION RESULT 1 Press UP button on the remote transmitter The motor will go up continuously 2 When the motor is close to the desired upper limit, press STOP button on the remote The motor stops running 3 Press either the UP or DOWN button The motor runs step by step to adjust upper limit accurately 4 Confirm the setting by pressing the CONFIRM button on the remote The motor jogs and the upper setting is completed

REMOTE 1. Press the SETTING button on the motor until the shade jogs once. Release the button immediately after the first jog - this should be not more than 3 seconds. 2. Repeat this step for all shades that will be controlled by a single channel. 3. Select the channel that you want to program using the CHANNEL selector button. 4. Press and hold the CONFIRM button until the shade(s) jogs once. 5. Repeat steps 1-4 to program the rest of the channels on a multi-channel remote. 6. To set the All function on the multi-channel remote, activate the setting buttons (step 1) on all shades. Press the CHANNEL button until all 5 indicator lights are lit. Then press confirm. ADVANCED PROGRAMMING REMOVE A SHADE FROM A REMOTE OR CHANNEL AND LINK IT TO A DIFFERENT REMOTE OR CHANNEL Unlink the motor from the remote - Note: this step also erases the lower and upper limits. 1. Remove the shade from the window. Press and hold the SETTING until it completes one jog/jog/jog cycle. 2. Release the “Setting” button. The original remote or channels have been unlinked. Link the motor to the new remote or channel 1. Follow the steps for replacing the remote above. 2. Set the lower and upper limits by following the instructions on page 6. P Setting (red button) Setting (red button) C L Confirm Limit 1 2 3 4 5 Up Stop Channel + Channel Indicator Lights Down Channel -

SKEW ADJUSTMENT (IF NECESSARY) If the shade does not raise evenly, first make sure the mounting brackets are mounted level with each other. If the shade is level and it still skews, operate the shade to the full down position. Prepare a strip of masking tape approximately 5” long. On the side of the shade opposite of the skewing direction, and as close to the end of the roller as possible, lift the fabric toward the back of the shade using your fingers and slide the tape with the sticky side facing the roller up as far as possible. The tape is to be running parallel to the roller. Roll the shade up and check for skewing. If the shade is still skewing, add another strip of tape on top of the first one. If the shade is now skewing in the opposite direction, tear off about 1” of tape from the last strip installed. The tape is to be torn from the end closest to the center of the shade. Place tape at this end Optional hold down brackets are mounted with the supplied screws. With the shade at its proper drop, place the pin of each hold down into the hole in each end cap and mark the screw holes. Make sure the pins are level and aligned. Raise the shade, then screw the hold down bracket into the mounting surface.

below. Partially lower the shade and insert a flat head screwdriver as shown. Twist the screwdriver until the head rail disengages from the bracket. As you release the brackets, support the head rail to keep it from falling. CLEANING AND CARE The shade fabric is easy to care for. Regular dusting with a feather duster or vacuum cleaner brush is recommended. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an unobtrusive corner of the shade. If you have any questions, call your dealer for advice. TROUBLE SHOOTING PROBLEM SOLUTION The motor does not work 1. Check that the power source and motor are connected properly 2. If using a battery wand - confirm that the batteries are fresh and are placed in the wand in the correct orientation. The motor continues to run in one direction The limit setting was unsuccessful and needs to be reset The indicator light on the remote does not shine or the remote-controlling range becomes shorter Replace the battery in the remote (CR2430 lithium) The motor stops working or works intermittently If using a battery wand, replace the batteries in the wand with 8 fresh AA alkaline batteries REPLACING THE BATTERY IN THE REMOTE Remove the battery tray from the remote by inserting a fingernail into the indentation on the back of the remote. To avoid the battery falling out of the remote, remove the tray while the remote is face up. Insert the new battery (CR2430 lithium) into the battery tray so that the writing is facing up when the remote is face up. Slide the tray back into the remote. Insert fingernail here LITHIUM BATTERY CR2430 3V