Mohu Beam Premium Manual 

BOX INCLUDES SAFETY PROCEDURES • Make sure there is another person present (on the ground) while installing the antenna. • DO NOT attempt to mount the antenna on a windy, rainy or snowy day. POWER LINE WARNING If you intend to mount the antenna on a rooftop, make sure to mount it at least 20 ft. away from any power lines or utility poles. IMPORTANT! FOLLOW ALL SAFETY PROCEDURES, WARNINGS AND INSTRUCTIONS WHEN INSTALLING YOUR ANTENNA. MOUNT THE ANTENNA AT LEAST 20 FT. FROM ALL POWER LINES OR UTILITY POLES. 20 FT. MINIMUM DANGER Use the included template on the bottom of this page to mark your mounting surface with the correct screw placement. Use the 3/16*32L wood screws for mounting in the holes you have marked with the template. You can also insert the included kickstand in one of the two screw slots to sit the antenna on a flat surface. OPTIONAL: To secure your antenna, install the included safety bracket above the antenna to block the antenna from being raised and removed from the screw slots. When antenna is sitting on a flat surface, use the included 90° coax adapter. 1 2 Antenna OPTIONAL: OR 8 6 7 Run the free end of the coaxial cable from the mounting location to the location of the TV. Connect the coaxial cable to the connector on the power injector. If needed, additional coaxial cable can be added. Excessive cable may cause reception loss. Connect the coaxial cable attached to the power injector to the ANT/IN connector on the back of the TV. NOTE: If using an RF splitter, turn to the next page and follow the RF splitter installation instructions. The power injector must be powered in order to function. Plug the amplifier’s USB cable into an open USB port on the back of the TV. If the TV does not have a USB port, use the included power adapter to power the power injector via any standard 120V wall outlet. Power Injector USB Cable (attached) Coaxial Cable (attached) ANT/IN Back of TV a. TV’s USB Port b. Wall Outlet* POWER OPTIONS: 3 4 5 *Actual USB power adapter may difer in appearance. [email protected] || 1.855.446.6648 || WWW.GOMOHU.COM In the TV’s setup menu, set the tuner mode to “Antenna” or “Air”. Refer to the TV manual for detailed instructions. In the TV’s setup menu, set TV to “scan” for channels. This can sometimes be listed as auto-program, auto-scan, channel search or channel scan. Refer to the TV manual for detailed instructions. Scanning For Channels Channel Search Antenna Tuner Mode 6 7 beam premium ™ INDOOR / OUTDOOR AMPLIFIED HDTV ANTENNA *Actual USB power adapter may difer in appearance. Beam Premium TM Antenna 10 ft. Coaxial Cable 6 ft. Coaxial Cable USB Power Adapter * Power Injector Antenna Mounting Hardware x2 - 16mm Wood Screws x2 - 3/16*32L Wood Screws Safety Bracket Antenna Kickstand 90° Coaxial Adapter Coaxial Coupler Attach end of the 10 ft. coaxial cable to the connector on the antenna. If you wish to extend the cable, use the included coupler and 6 ft. coaxial cable. Coax Cable Coax Cable Optional Coax Coupler

targets to mark your wall through the paper. You will drive screws into these spots and the antenna will mount perfectly. WALL MOUNT TEMPLATE HAVING PROBLEMS? THIS CAN HELP! Get It Up High A general rule of thumb for antenna placement is the higher you can get it, the better reception you will have. Reception can even be improved by placing the antenna in windows that are facing the direction of the towers. Most customers try several locations until they locate the spot where they get the most channels. Please remember that every time you move your antenna you will need to run your channel scan again. Get It Away From Metal Many types of buildings can block reception because of the materials used to construct your home/condo/apartment. Metal acts as a barrier that in essence cages the signals and bounces them around making it almost impossible for the signals to "land" on the antenna. For an antenna to work efectively in this situation it must be moved away from large metal objects, placed in a window facing the direction of the towers, or a roof antenna is needed to get the antenna up and over the blockage. SIGNAL STRENGTH Make Sure the Power Injector is Plugged-In The power injector must be plugged into both the antenna and a power source - either a USB port on your TV or the provided USB power adaptor. If the power injector is not receiving enough power from your TV or another source, it will block the TV signal. Have antenna questions? Contact Mohu Support Monday-Friday 8 a.m. - 5 p.m. ET 1 2 3 1-855-446-6648 [email protected]