Konig Security SEC-TRANS10 Manual 

MANUAL (page 2) WIRELESS OBSERVATION SYSTEM MODE D´EMPLOI (p. 12) SYSTEME D'OBSERVATION SANS FIL GEBRUIKSAANWIJZING (p. 17) DRAADLOOS OBSERVATIESYSTEEM MANUALE (p. 21) SISTEMA DI OSSERVAZIONE WIRELESS MANUAL DE USO (p. 27) SISTEMA DE OBSERVACIÓN INALÁMBRICO HASZNÁLATI ÚTMUTATÓ (p. 32) VEZETÉK NÉLKÜLI MEGFIGYELŐ RENDSZER KÄYTTÖOHJE (p. 37) LANGATON VALVONTAJÄRJESTELMÄ BRUKSANVISINING (p. 42) TRÅDLÖST ÖVERVAKNINGSSYSTEM NÁVOD K POUŽITÍ (str. 47) BEZDRÁTOVÝ SLEDOVACÍ SYSTÉM ANLEITUNG (p. 7) DRAHTLOSES ÜBERWACHUNGSSYSTEM MANUAL DE UTILIZARE (p. 52) SISTEM DE SUPRAVEGHERE WIRELESS

With IR LEDs for night vision. Monitor with screen reverse function and menu for personal settings. Extra AV input for external source and AV output for recording. Also ideal as baby monitor. Description camera: 1. IR LED and lens 2. Fastening/ bracket thread 3. Power Jack 4. Microphone 5. Transmitter antenna 6. Channel switch 7. DC Power 8. Camera bracket Installing outdoor unit: Select a suitable position from which you want to monitor the desired object. This position must not been screened off by (too many) concrete walls, mirrors, metal shelves, etc. There should not be any appliances with strong electric fi eld close to the camera or the TFT/LCD monitor. Any strong electric environment could cause interference and reduce the performance. Connecting the camera: 1. Connect the 7.5 V adaptor cord into the DC Input Jack of the camera. 2. Plug the adaptor into a standard (100V-240V) AC outlet. 3. Be sure to set the same channel to both camera and TFT/LCD monitor. ATTENTION: Wrong adaptor connected to the camera may cause damage to the camera. • Screw the wall bracket with the supplied screws to a suitable wall or a suitable platform use dow- els if relevant. • Guide the tripod thread of the wall bracket into the thread hole of the camera and screw each of them to one another. • Align the camera and screw the T bolt tight. 1 2 3 4 5 7 6 8

b. Increase the value in OSD (On Screen Display) VOL- a. Decrease the volume level b. Decrease the value in OSD (On Screen Display) FUNC (Function key) The system offers a variety of OSD features that allows to adjust manually for best image performance. Under each OSD, it‘s possible to adjust the value by pressing „VOL+“ and „VOL-“ buttons. a. Press once for BRIGHTNESS adjustment b. Press twice for CONTRAST adjustment c. Press three times for SHARPNESS adjustment d. Press four times for COLOR adjustment e. Press fi ve times for SCALE adjustment (16:9, 4:3) f. Press six times for VIDEO (PAL/NTSC) adjustment g. Press seven times for OSD BRIGHTNESS adjustment h. Press eight times for LCD H. AMPLITUDE (scanning line) adjustment i. Press nine times for returning back to display mode REV (Screen reverse) Description monitor: 1 2 3 4 5 7 6 8 9 13 11 12 10 1. Dipole Antenna 2. Channel display LED indicator 3. Volume (+) 4. Volume (-) 5. Function key (OSD control for brightness, contrast control, etc.) 6. Screen reverse 7. Power ON/OFF 8. CH Select / Auto switch 9. Bracket stand 10. A/V output 11. A/V input 12. DC Power 13. DC Power supply Default Mirroring Reverse Reverse & Mirroring Default Screen reverse function. Press the REV button till the desired image is shown.

1. Plug the 12 VDC adapter plug into the DC input jack. 2. Plug the adapter into a standard (100V-240 V) AC outlet. Press the ON/OFF button to turn on LCD monitor. 3. A/V input can be connected with an external audio/video source 4. A/V output on the LCD monitor can be connected to a TV, monitor or DVR/VCR for recording. Bracket Stand at the back of LCD monitor can be pulled out to put the LCD monitor on any solid and fl at surface. ON/OFF Button to switch the monitor ON or OFF. CH (Channel select / Auto switch) Press the button to switch between the 4 channels. The system presets to CH1 by default. Press the bottom once to switch to CH2, press again to switch to CH3, press again to switch to CH4, press again to switch to auto-scan mode. Channel selection on the LCD monitor When one camera is installed, select with the CH button the same channel as chosen on the camera. If two or more cameras (CH2, CH3, etc.) are installed, press CH again to switch to the desired camera. If pressed 4 times on the CH button (all LED indicators will light up), the monitor will switch to auto scan mode and display all installed cameras in a sequence with 5 seconds interval. Press again the CH button to stop the auto scan mode. System Installation: When installing the camera, check the reception of the LCD monitor fi rst before fi nal installation. Select the same channel (Channel 1-4, as indicated on Channel Label) to be used on both the camera and LCD monitor. Channel selection on the camera The camera can be set up in four different optional channels. To set the channel selection switch, use a pointed object, e.g. a ballpoint pen, to select the desired channel (No.1 or No.2 or No.3 or No.4) to position „ON“. Only one channel is activated on one camera. Camera Set to Channel 1 Camera Set to Channel 2 Camera Set to Channel 3 Camera Set to Channel 4

• Current consumption: 300 mA • Transmitting frequency: 2.4-2.4835 GHz • Modulation: FM • Channels: 4 • Light sensitivity: 1-8 Lux • Picture sensor: 1/3“ CMOS, 628 x 582 • IR LED: 11IR/1CDS • Resolution: 330 TV lines, horizontal • Microphone: mono • Picture: colour • Range: indoor ±30 m, open area ±100 m • Operating temperature: -10°C to +50°C • Weight: 140 g (without bracket) • Dimensions: 100 x 38 x 40mm (without aerial) TFT/LCD monitor: • Operating voltage: 12 VDC • Current consumption: 1000 mA • Transmitting frequency: 2.4-2.4835GHz • Channels: 4 • Size: 7“ TFT/LCD • Video output level: 1Vp-p/75 Ohm • Audio output level: 1Vp-p/600 Ohm, mono • Audio/video connector: 3.5mm jack • Light sensitivity: 3 Lux • Range: indoor ±30m, open area ±100m • Operating temperature: -10°C to +50°C • Weight: 680 g • Dimensions: 184 x 52.7 x 127mm (without aerial) Declaration of conformity We, Nedis B.V. De Tweeling 28 5215MC ’s-Hertogenbosch The Netherlands Tel.: 0031 73 599 1055 Email: [email protected] Declare that product: Name: König Security Model: SEC-TRANS10 Description: 2.4GHz wireless observation system Is in conformity with the following standards EN 300 440-1: V.1.3.1, EN 300 440-2: V.1.1.1 EN 301489-1:V1.6.1:2005, EN 301489-3: V1.4.1:2002 EN 60065: 2002 Following the provisions of the 1999/5/EC R&TTE directive.