Avalue Technology ECM-BDWH Operation & User’s Manual

ECM-BDWH Intel® Core ™ Processors 3.5” Micro Module with Intel® QM87 Chipset User’s manual 1st Ed – 16 September 2015

FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. Notice This guide is designed for experienced users to setup the system within the shortest time. For detailed information, please always refer to the electronic user's manual. Copyright Notice Copyright  2015 Avalue Technology Inc., ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer Avalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Avalue Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that

these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. Avalue Technology Inc. makes no representation or warranty that such application will be suitable for the specified use without further testing or modification. Life Support Policy Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. A Message to the Customer Avalue Customer Services Each and every Avalue’s product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Avalue device is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Avalue has come to be known. Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully. Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw/

Product Warranty Avalue warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Avalue, or which have been subject to misuse, abuse, accident or improper installation. Avalue assumes no liability under the terms of this warranty as a consequence of such events. Because of Avalue’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If any of Avalue’s products is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time, and freight. Please consult your dealer for more details. If you think you have a defective product, follow these steps: 1. Collect all the information about the problem encountered. (For example, CPU type and speed, Avalue’s products model name, hardware & BIOS revision number, other hardware and software used, etc.) Note anything abnormal and list any on-screen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information available. 3. If your product is diagnosed as defective, obtain an RMA (return material authorization) number from your dealer. This allows us to process your good return more quickly. 4. Carefully pack the defective product, a complete Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

CONTENT 1. Getting Started.................................................................................................... 8 1.1 Safety Precautions.......................................................................................... 8 1.2 Packing List.................................................................................................... 8 1.3 Document Amendment History ........................................................................ 9 1.4 Manual Objectives ........................................................................................ 10 1.5 System Specifications ................................................................................... 11 1.6 Architecture Overview – Block Diagram.......................................................... 13 2. Hardware Configuration ................................................................................... 14 2.1 Product Overview ......................................................................................... 15 2.2 Installation Procedure ................................................................................... 17 2.2.1 Main Memory ................................................................................................................. 18 2.3 Jumper and Connector List............................................................................ 20 2.4 Setting Jumpers & Connectors ...................................................................... 22 2.4.1 Clear CMOS (JBAT1)...................................................................................................... 22 2.4.2 COM 1 pin 9 signal select (JRI1)...................................................................................... 22 2.4.3 AT/ ATX Input power select (JAT1) .................................................................................. 23 2.4.4 LCD backlight brightness adjustment (JVR1) .................................................................... 23 2.4.5 5VSB connector in ATX (PWR_SB1)................................................................................ 24 2.4.6 Battery connector (BT1) .................................................................................................. 24 2.4.7 CPU fan connector (CPU_FAN1) ..................................................................................... 25 2.4.8 System fan connector (SYS_FAN1) ................................................................................. 25 2.4.9 COM 1 RS-422-485 connector (RS422_1)........................................................................ 26 2.4.10 LCD inverter connector (JBKL1) ...................................................................................... 26 2.4.11 Audio connector (JAUDIO1) .............................................................................................. 27 2.4.11.1 Signal Description – Audio connector (JAUDIO1) ................................................ 27 2.4.12 Low pin count connector (JLPC1) .................................................................................... 28 2.4.13 Serial port 2 connector (COM2) ....................................................................................... 28 2.4.14 General purpose I/O connector (JDIO1) ........................................................................... 29 2.4.15 Miscellaneous setting connector (JFP1) ........................................................................... 29 2.4.16 SPI connector (JSPI1)..................................................................................................... 30 2.4.17 Power connector (PWR1) ................................................................................................ 30 2.4.18 SATA power connector (SATA_PWR1) ............................................................................ 31 2.4.19 EC Debug connector (CN2) ............................................................................................. 31 2.4.20 LVDS connector (JLVDS1) .............................................................................................. 32 2.4.21 On-board box header for USB3.0 (JUSB3/4) .................................................................... 33 2.4.22 On-board box header for USB3.0 (JUSB5/6) .................................................................... 33

2.4.23 On-board box header for USB2.0 (JUSB7/8) .................................................................... 34 2.4.24 PS/2 keyboard & mouse connector (JKB/ MS1) ................................................................ 34 2.5 Audio / USB Daughter Board User’s Guide ..................................................... 35 2.5.1 Jumper and Connector Layout ......................................................................................... 35 2.5.2 Jumper and Connector List.............................................................................................. 35 2.5.3 Setting Jumper and Connector ........................................................................................ 36 3. BIOS Setup ........................................................................................................... 37 3.1 Introduction .................................................................................................. 38 3.2 Starting Setup .............................................................................................. 38 3.3 Using Setup ................................................................................................. 39 3.4 Getting Help ................................................................................................. 40 3.5 In Case of Problems ..................................................................................... 40 3.6 BIOS setup................................................................................................... 41 3.6.1 Main Menu ..................................................................................................................... 41 3.6.1.1 System Language ............................................................................................. 42 3.6.1.2 System Date ..................................................................................................... 42 3.6.1.3 System Time .................................................................................................... 42 3.6.2 Advanced Menu.............................................................................................................. 43 3.6.2.1 CPU Configuration ............................................................................................ 43 3.6.2.2 APCI Settings ................................................................................................... 45 3.6.2.3 Platform Information .......................................................................................... 46 3.6.2.3.1 Intel TXT Information......................................................................................... 46 3.6.2.3.2 Intel RC Drivers Version Detail........................................................................... 47 3.6.2.4 Super IO Configuration ...................................................................................... 47 3.6.2.4.1 Serial Port 1 Configuration ................................................................................. 48 3.6.2.4.2 Serial Port 2 Configuration ................................................................................. 49 3.6.2.5 PCH-FW Configuration ...................................................................................... 50 3.6.2.5.1 Firmware Update Configuration.......................................................................... 50 3.6.2.6 AMT Configuration ............................................................................................ 51 3.6.2.7 H/W Monitor ..................................................................................................... 52 3.6.2.7.1 Smart Fan Mode Configuration .......................................................................... 53 3.6.2.8 S5 RTC Wake Settings...................................................................................... 54 3.6.2.9 Serial Port Console Redirection ......................................................................... 56 3.6.2.10 SATA Configuration .......................................................................................... 56 3.6.2.11 Thermal Configuration ....................................................................................... 57 3.6.2.11.1 Platform Thermal Configuration.......................................................................... 58 3.6.2.12 Network Stack .................................................................................................. 59 3.6.2.13 CSM Configuration............................................................................................ 60 3.6.2.14 USB Configuration ............................................................................................ 61 3.6.3 Chipset......................................................................................................................... 62

3.6.3.1 System Agent (SA) Configuration ..................................................................... 62 3.6.3.1.1 Graphics Configuration .................................................................................... 63 3.6.3.1.1.1 LCD Control .................................................................................................... 64 3.6.3.1.2 Memory Configuration ..................................................................................... 65 3.6.3.2 PCH-IO Configuration ...................................................................................... 66 3.6.3.2.1 PCI Express Configuration ............................................................................... 67 3.6.3.2.1.1 PCI Express Root Port 1 .................................................................................. 67 3.6.3.2.2 USB Configuration........................................................................................... 68 3.6.3.2.3 PCH Azalia Configuration ................................................................................ 69 3.6.3.2.4 BIOS Security Configuration ............................................................................ 69 3.6.4 Security ........................................................................................................................ 70 3.6.4.1 Secure Boot menu........................................................................................... 71 3.6.4.1.1 Key Management ............................................................................................ 71 3.6.4 Boot ............................................................................................................................. 72 3.6.6 Save and Exit ............................................................................................................... 73 3.6.6.1 Save Changes and Reset ................................................................................ 73 3.6.6.2 Discard Changes and Reset............................................................................. 73 3.6.6.3 Restore Defaults ............................................................................................. 73 4. Drivers Installation ............................................................................................... 74 4.1 Install Chipset Driver ..................................................................................... 75 4.2 Install ME Driver ........................................................................................... 76 4.3 Install USB 3.0 Driver .................................................................................... 77 4.4 Install VGA Driver ......................................................................................... 78 4.5 Install Audio Driver (For Realtek ALC892) ...................................................... 79 4.6 Install Ethernet Driver (For Intel I210AT and I217LM) ...................................... 80 5. Mechanical Drawing ............................................................................................. 81

1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. 1.2 Packing List Before you begin installing your single board, please make sure that the following materials have been shipped:  1 x 3.5” ECM-BDWH Micro Module  1 x AUX-056 daughter board  1 x DVD-ROM contains the followings: — User’s Manual (this manual in PDF file) — Ethernet driver and utilities — VGA drivers and utilities — Audio drivers and utilities  1 x cable set contains the followings: — 1 x Audio cable (12pin,2.0 pitch) — 1 x USB 2.0 cable (10P/2.0mm-10P/2.0mm) — 1 x USB 3.0 cable ((20P/2.0mm-20P/2.0mm) — 1 x Serial ATA cable (7-pin, standard) — 1 x Wire SATA power cable (15-pin,4P/2.5mm) — 1 x Flat cable 9P(M)-PHD 10P/2.0mm)  3M foam (VHB-4622 10mm*20mm*1.1mm)

1.3 Document Amendment History Revision Date By Comment 1st September 2015 Avalue Initial Release

1.4 Manual Objectives This manual describes in detail the Avalue Technology ECM-BDWH Single Board. We have tried to include as much information as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the understanding of this board. We strongly recommend that you study this manual carefully before attempting to interface with ECM-BDWH series or change the standard configurations. Whilst all the necessary information is available in this manual we would recommend that unless you are confident, you contact your supplier for guidance. Please be aware that it is possible to create configurations within the NVRAM that make booting impossible. If this should happen, clear the NVRAM settings, (see the description of the Jumper Settings for details). If you have any suggestions or find any errors concerning this manual and want to inform us of these, please contact our Customer Service department with the relevant details.

1.5 System Specifications System CPU Onboard 5th generation Intel® mobile Core™ i7 BGA processors (47W CPU) BIOS AMI uEFI BIOS, 128 Mbit SPI Flash ROM iAMT9.0 supported System Chipset Intel® QM87 I/O Chip EC(IT8518E) System Memory 1 x 204-pin 1.35V DDR3L SODIMM SSD 1 x mSATA (from Mini PCIe slot) Watchdog Timer H/W Reset, 1sec. – 65535sec. H/W Status Monitor CPU & system temperature monitoring Voltages monitoring Expansion 1 x mini-PCIe (mSATA supported) I/O MIO 2 x SATA III,1 x RS232, 1 x RS232/422/485, LPC USB 4 x USB3.0 (Wafer), 2 x USB 2.0 (Wafer), 2 x USB 3.0 (Edge connectors) GPIO 4-bit GPI, 4-bit GPO Display Chipset Intel® QM87 Resolution VGA: 1920x2000@60Hz LVDS: 1920x1080@60Hz HDMI: 3840x2160@24Hz Multiple Display Triple independent display HDMI 1 x HDMI LCD Interface Dual channel 18/24-bit LVDS Audio AC97 Codec Realtek ALC892 Supports 5.1-CH Audio Ethernet LAN Chip 1 x Intel I210AT GbE controller 1 x Intel I217LMGbE PHY Ethernet Interface 10/100/1000 Base-Tx compatible I/O CMOS Battery CR2032 COM 1 x RS232/422/485 Rear I/O USB 2 x USB3.0

LAN 2 x Ethernet HDMI 1 x HDMI LED Front Panel LED Connector (for system use) COM 1 x RS232 Mechanical & Environmental Power Requirement +12V ACPI Single power ATX Support S0, S3, S4, S5 ACPI 3.0 Compliant Power Type AT/ATX Operating Temp. 0°C ~ 60°C Storage Temp. -40°C ~ 75°C Operating Humidity 0%~90% relative humidity, non-condensing Size (L x W) (Please consult product engineers for the production feasibility if the size is larger than 410x360mm or smaller than 80x70mm) 5.7" x 4" (146mm x 101mm) Weight 0.44lbs (0.2kg) Note: Specifications are subject to change without notice.

1.6 Architecture Overview – Block Diagram The following block diagram shows the architecture and main components of ECM-BDWH.

2.2 Installation Procedure This chapter explains you the instructions of how to setup your system. 1. Turn off the power supply. 2. Insert the SODIMM module (be careful with the orientation). 3. Insert all external cables for hard disk, floppy, keyboard, mouse, USB etc. except for flat panel. A CRT monitor must be connected in order to change NVRAM settings to support flat panel. 4. Connect power supply to the board via the ATXPWR. 5. Turn on the power. 6. Enter the BIOS setup by pressing the delete key during boot up. Use the "Save & Exit \ Restore Defaults" feature. 7. If TFT panel display is to be utilized, make sure the panel voltage is correctly set before connecting the display cable and turning on the power. Note: Make sure the heat sink and the CPU top surface are in total contact to avoid CPU overheating problem that would cause the system to hang or unstable

2.2.1 Main Memory ECM-BDWH provides one 204-pin DDR3L SODIMM socket, supports up to 8GB DDR3L 1333/1600 SDRAM. (Rear side) Make sure to unplug the power supply before adding or removing SODIMMs or other system components. Failure to do so may cause severe damage to both the board and the components.  Locate the SODIMM socket on the board.  Hold two edges of the SODIMM module carefully. Keep away of touching its connectors.  Align the notch key on the module with the rib on the slot.  Firmly press the modules into the socket automatically snaps into the mounting notch. Do not force the SODIMM module in with extra force as the SODIMM module only fit in one direction. SODIMM

 To remove the SODIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the SODIMM module. Note: (1) Please do not change any DDR3 SDRAM parameter in BIOS setup to increase your system’s performance without acquiring technical information in advance. (2) Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly.

2.3 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either two pins. The jumper settings are schematically depicted in this manual as follows: A pair of needle-nose pliers may be helpful when working with jumpers. Connectors on the board are linked to external devices such as hard disk drives, a keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to configure your system to suit your application. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. The following tables list the function of each of the board's jumpers and connectors. Jumpers Label Function Note JBAT1 Clear CMOS 3 x 1 header, pitch 2.00 mm JRI1 COM 1 pin 9 signal select 3 x 2 header, pitch 2.00 mm JAT1 AT/ ATX Input power select 3 x 1 header, pitch 2.00 mm JVR1 LCD backlight brightness adjustment 3 x 1 header, pitch 2.00 mm Connectors Label Function Note BT1 Battery connector 2 x 1 wafer, pitch 1.25 mm CPU_FAN1 CPU fan connector 4 x 1 wafer, pitch 2.54 mm HDMI1 HDMI connector RS422_1 COM 1 RS-422-485 connector 3 x 2 wafer, pitch 2.00 mm JAUDIO1 Audio connector 6 x 2 wafer, pitch 2.00 mm

JBKL1 LCD inverter connector 5 x 1 wafer, pitch 2.00 mm COM1 Serial port 1 connector D-sub 9-pin, male COM2 Serial port 2 connector 5 x 2 wafer, pitch 2.00 mm JDIO1 General purpose I/O connector 6 x 2 wafer, pitch 2.00 mm JFP1 Miscellaneous setting connector 5 x 2 wafer, pitch 2.00 mm JLPC1 Low pin count interface 7 x 2 header, pitch 2.00 mm JLVDS1 LVDS connector 20 x 2 header, pitch 1.25 mm JSPI1 SPI connector 4 x 2 header, pitch 2.00 mm USB1/2 On-board connector for USB3.0 JUSB3/4 On-board box header for USB3.0 10 x 2 wafer, pitch 2.00 mm JUSB5/6 On-board box header for USB3.0 10 x 2 wafer, pitch 2.00 mm JUSB7/8 On-board box header for USB2.0 5 x 2 wafer, pitch 2.00 mm CN2 EC Debug connector 2 x 1 header, pitch 2.00 mm LAN1/LAN2 RJ-45 Ethernet connector LED1 LED connector PWR_SB1 5VSB connector in ATX 3 x 1 wafer, pitch 2.54 mm PWR1 Power connector 2 x 2 wafer, pitch 4.20 mm JKB/MS1 PS/2 keyboard & mouse connector 2 x 3 wafer, pitch 2.00 mm SATA_PWR1 SATA power connector 1 x 4 wafer, pitch 2.50 mm SATA1 Serial ATA connector 1 SATA2 Serial ATA connector 2 SYS_FAN1 System fan connector 4 x 1 wafer, pitch 2.54 mm VGA1 VGA connector D-sub 15-pin, female MPCIE2 Mini-PCI connector CN1 DDR3 SODIMM connector

2.4 Setting Jumpers & Connectors 2.4.1 Clear CMOS (JBAT1) * Default Protect* Clear CMOS 2.4.2 COM 1 pin 9 signal select (JRI1) * Default Ring* +5V +12V

2.4.3 AT/ ATX Input power select (JAT1) * Default AT* ATX 2.4.4 LCD backlight brightness adjustment (JVR1) * Default PWM Mode* DC Mode

2.4.5 5VSB connector in ATX (PWR_SB1) Signal PIN PSON_ATX# 1 GND 2 +ATX5VSB 3 2.4.6 Battery connector (BT1) Signal PIN +3.3V 1 GND 2

2.4.7 CPU fan connector (CPU_FAN1) Signal PIN GND 1 +12V 2 Tachometer0 3 FAN_PWM0 4 2.4.8 System fan connector (SYS_FAN1) Signal PIN GND 1 +12V 2 Tachometer1 3 FAN_PWM1 4

2.4.9 COM 1 RS-422-485 connector (RS422_1) Signal PIN PIN Signal 485_422TX1- 2 1 422RX1- 485_422TX1+ 4 3 422RX1+ +5V 6 5 GND Note: This connector is available after modify the mode of COM1 in BIOS setting 2.4.10 LCD inverter connector (JBKL1) Signal PIN +12V 1 GND 2 BKLEN 3 VBRIGHT 4 +5V 5

2.4.11 Audio connector (JAUDIO1) Signal PIN PIN Signal GND 11 12 MIC1-JD LINE1-JD 9 10 FRONT-JD MIC1-L-IN 7 8 MIC1-R-IN LINE1-L-IN 5 6 LINE1-R-IN GND 3 4 GND FRONT-L-OUT 1 2 FRONT-R-OUT 2.4.11.1 Signal Description – Audio connector (JAUDIO1) Signal Signal Description LINE1_JD AUDIO IN (LINE_RIN/LIN)sense pin FRONT_JD AUDIO Out(ROUT/LOUT) sense pin MIC1_JD MIC IN (MIC_RIN/LIN) sense pin

2.4.12 Low pin count connector (JLPC1) Signal PIN PIN Signal LPC_AD0 1 2 +3.3V LPC_AD1 3 4 LPC_RESET# LPC_AD2 5 6 LPC_LFRAME# LPC_AD3 7 8 CLK_PCI_LPC SERIRQ 9 10 GND +V5S 11 12 GND +V5A 13 14 LPC_LDRQ0# 2.4.13 Serial port 2 connector (COM2) Signal PIN PIN Signal NRXDB 2 1 NDCDB# NDTRB# 4 3 NTXDB NDSRB# 6 5 GND NCTSB# 8 7 NRTSB# NC 10 9 NRIB#

2.4.14 General purpose I/O connector (JDIO1) Signal PIN PIN Signal +5V 11 12 GND SMB_DATA_9555 9 10 SMB_CLK_9555 DIO_GP13 7 8 DIO_GP23 DIO_GP12 5 6 DIO_GP22 DIO_GP11 3 4 DIO_GP21 DIO_GP10 1 2 DIO_GP20 2.4.15 Miscellaneous setting connector (JFP1) Signal PIN PWBT 1 2 RST# 3 4 PWR-LED- 5 PWR-LED+ 6 HDD-LED+ 7 HDD-LED- 8 COPEN# 9 10

2.4.16 SPI connector (JSPI1) Signal PIN PIN Signal 7 HOLD# SPI_SI 6 5 SPI_SO SPI_CLK 4 3 SPI_CS0# GND 2 1 +3.3V 2.4.17 Power connector (PWR1) Signal PIN PIN Signal GND 1 2 GND +12V 3 4 +12V

2.4.18 SATA power connector (SATA_PWR1) Signal PIN GND 1 GND 2 +5V 3 +5V 4 2.4.19 EC Debug connector (CN2) Signal PIN EC_SMCLK_DEBUG 1 EC_SMDAT_DEBUG 2

2.4.20 LVDS connector (JLVDS1) Signal PIN PIN Signal +12V 39 40 +12V GND 37 38 GND LVDS_CLK2_N 35 36 LVDS_CLK1_N LVDS_CLK2_P 33 34 LVDS_CLK1_P GND 31 32 GND LVDS_DATA7_N 29 30 LVDS_DATA6_N LVDS_DATA7_P 27 28 LVDS_DATA6_P GND 25 26 GND LVDS_DATA5_N 23 24 LVDS_DATA4_N LVDS_DATA5_P 21 22 LVDS_DATA4_P GND 19 20 GND LVDS_DATA3_N 17 18 LVDS_DATA2_N LVDS_DATA3_P 15 16 LVDS_DATA2_P GND 13 14 GND LVDS_DATA1_N 11 12 LVDS_DATA0_N LVDS_DATA1_P 9 10 LVDS_DATA0_P GND 7 8 GND NC 5 6 NC +3.3V 3 4 +5V +3.3V 1 2 +5V

2.4.21 On-board box header for USB3.0 (JUSB3/4) Signal PIN PIN Signal 1 USBVCC USBVCC 19 2 USB3_RXN3_L USB3_RXN4_L 18 3 USB3_RXP3_L USB3_RXP4_L 17 4 GND GND 16 5 USB3_TXN3_L USB3_TXN4_L 15 6 USB3_TXP3_L USB3_TXP4_L 14 7 GND GND 13 8 USB_PN_Z_4 USB_PN_Z_6 12 9 USB_PP_Z_4 USB_PP_Z_6 11 10 NC 2.4.22 On-board box header for USB3.0 (JUSB5/6) Signal PIN PIN Signal 1 USBVCC USBVCC 19 2 USB3_RXN5_L USB3_RXN6_L 18 3 USB3_RXP5_L USB3_RXP6_L 17 4 GND GND 16 5 USB3_TXN5_L USB3_TXN6_L 15 6 USB3_TXP5_L USB3_TXP6_L 14 7 GND GND 13 8 USB_PN_Z_8 USB_PN_Z_10 12 9 USB_PP_Z_8 USB_PP_Z_10 11 10 NC

2.4.23 On-board box header for USB2.0 (JUSB7/8) Signal PIN PIN Signal USBVCC 2 1 USBVCC USB_PN_Z_13 4 3 USB_PN_Z_12 USB_PP_Z_13 6 5 USB_PP_Z_12 GND 8 7 GND GND 10 9 GND 2.4.24 PS/2 keyboard & mouse connector (JKB/ MS1) Signal PIN PIN Signal KBDT 2 1 KBCK GND 4 3 KBVCC MSDT 6 5 MSCK

2.5 Audio / USB Daughter Board User’s Guide 2.5.1 Jumper and Connector Layout 2.5.2 Jumper and Connector List Connectors Label Function Note AUSB2 USB connector 2.0 AUSB3 USB connector 3.0 MIC1 Mic in connector Phone Jack LINEOUT1 Line out connector Phone Jack LINEIN1 Line in connector Phone Jack AJAUDIO1 Audio connector 6 x 2 header, pitch 2.00mm AJUSB2 2.00mm USB connector 5 x 2 header, pitch 2.00mm AJUSB3 2.00mm USB connector 10 x 2 header, pitch 2.00mm

2.5.3 Setting Jumper and Connector Audio Connector (AJAUDIO1) 2.00mm USB Connector (AJUSB2) Signal PIN PIN Signal AFRONT1-L-OUT 1 2 AFRONT1-R-OUT GND 3 4 GND ALINE1-L-IN 5 6 ALINE1-R-IN AMIC1-L-IN 7 8 AMIC1-R-IN ALINE1-JD 9 10 AFRONT1-JD GND 11 12 AMIC1-JD Signal PIN PIN Signal USB2VCC 1 2 USB2VCC AUSB_PN2 3 4 AUSB_PN1 AUSB_PP2 5 6 AUSB_PP1 GND 7 8 GND GND 9 10 GND 2.00mm USB Connector (AJUSB3) Signal PIN PIN Signal AUSBVCC2 1 AUSB3_RXN1_L 2 19 AUSBVCC3 AUSB3_RXP1_L 3 18 AUSB3_RXN2_L GND 4 17 AUSB3_RXP2_L AUSB3_TXN1_L 5 16 GND AUSB3_TXP1_L 6 15 AUSB3_TXN2_L GND 7 14 AUSB3_TXP2_L AUSB_PN3 8 13 GND AUSB_PP3 9 12 AUSB_PN4 NC 10 11 AUSB_PP4

3.1 Introduction The BIOS setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed. 3.2 Starting Setup The AMI BIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contained in the NVRAM and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways: By pressing or immediately after switching the system on, or By pressing the or key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test). Press or to enter SETUP If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing , , and keys. Remove all storage can also enter the BIOS Setup Utility.

3.3 Using Setup In general, you use the arrow keys to highlight items, press to select, use the PageUp and PageDown keys to change entries, press for help and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Button Description ↑ Move to previous item ↓ Move to next item ← Move to the item in the left hand → Move to the item in the right hand Esc key Main Menu -- Quit and not save changes into NVRAM Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu PGUP/HOME key Go to Top of Screen PGDN/END key Go to Bottom of Screen + key Increase the numeric value or make changes - key Decrease the numeric value or make changes F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 key Previous Values. F3 key Optimized defaults F4 key Save & Exit Setup  Navigating Through The Menu Bar Use the left and right arrow keys to choose the menu you want to be in. Note: Some of the navigation keys differ from one screen to another.  To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press . A “” pointer marks all sub menus.

3.4 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press or key. 3.5 In Case of Problems If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the AMI BIOS supports an override to the NVRAM settings which resets your system to its defaults. The best advice is to only alter settings which you thoroughly understand. To this end, we strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override.

3.6 BIOS setup Once you enter the Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and exit choices. Use the arrow keys to select among the items and press to accept and enter the sub-menu. 3.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock.

3.6.1.1 System Language This option allows choosing the system default language. 3.6.1.2 System Date Use the system time option to set the system time. Manually enter the hours, minutes and seconds. 3.6.1.3 System Time Use the system Date option to set the system date. Manually enter the day, month and year. Note: The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen. Visit the Avalue website (www.avalue.com.tw) to download the latest product and BIOS information.

3.6.2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. 3.6.2.1 CPU Configuration Use the CPU configuration menu to view detailed CPU specification and configure the CPU.

Item Options Description Hyper-threading Disabled Enabled[Default] Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled. Active Processor Cores All[Default] 1/2/3 Number of cores to enable in each processor package EIST Disabled Enabled[Default] Enable/Disable Intel SpeedStep. Turbo Mode Disabled[Default] Enabled Turbo Mode. To Enabled Turbo Mode, please make sure your thermal solution is good enough. Note: In order to maximize the effectiveness of the turbo boost, the system need to have the corresponding thermal design. CPU C states Disabled Enabled[Default] Enable or disable CPU C states. Enhanced C1 state Disabled Enabled[Default] Enhanced C1 state. CPU C3/6 Report Disabled Enabled[Default] Enable/Disable CPU C3/6 report to OS. C6 Latency Short[Default] Long Configure Short/Long latency for C6. Intel TXT(LT) Support Disabled[Default] Enabled Enables or Disables Intel® TXT(LT) support.

3.6.2.2 APCI Settings Item Options Description Enable ACPI Auto Configuration Disabled[Default] Enabled Enable or Disable BIOS ACPI Auto Configuration. Enable Hibernation Disabled Enabled[Default] Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS. APCI Sleep State Suspend Disabled S3 (Suspend to RAM)[Default] Select ACPI sleep state the system will enter when the SUSPEND button is pressed. S3 Video Repost Disabled[Default] Enabled Enable or Disable S3 Video Repost. ErP Function Disabled[Default] Enabled ErP Function (Deep S5). Pwr-On After PWR-Fail Off[Default] On Last State Select the power station after power failure. Wake Up by Ring Disabled[Default] Enabled System wake up by ring (from S3~S5). Watch Dog Disabled[Default] 30 sec 40 sec 50 sec 1 min 2 min 10 min 30 min Select Watch Dog Timer (WDT) Mode.

3.6.2.3.2 Intel RC Drivers Version Detail 3.6.2.4 Super IO Configuration You can use this item to set up or change the IT8518 Super IO configuration. Please refer to 3.6.2.4.1~2 for more information.

3.6.2.4.1 Serial Port 1 Configuration Item Option Description Serial Port Enabled[Default], Disabled Enable or Disable Serial Port (COM) Change Settings Auto[Default] IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Select an optimal setting for Super IO Device. UART 232 422 485 UART 232[Default], UART 422, UART485 Change the Serial Port as RS232/422/485.

3.6.2.4.2 Serial Port 2 Configuration Item Option Description Serial Port Enabled[Default] Disabled Enable or Disable Serial Port (COM) Change Settings Auto[Default] IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Select an optimal setting for super IO Device.

3.6.2.5 PCH-FW Configuration Item Description Firmware Update Configuration Configure Management Engine Technology Parameters. 3.6.2.5.1 Firmware Update Configuration Item Options Description Me FW Image Re-Flash Disabled[Default] Enabled Enable/Disable Me FW Image Re-Flash function.

3.6.2.6 AMT Configuration Intel AMT allows hardware-based remote management, security, power-management, and remote-configuration features. Item Options Description Intel AMT Enabled[Default] Disabled Enable/Disable Intel ® Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device Un-Configure ME Disabled[Default] Enabled OEMFLag Bit 15: Un-Configure ME without password Disable ME Disabled[Default] Enabled Set ME to Soft Temporary Disabled.

3.6.2.7 H/W Monitor Displays system health status Item Description Smart Fan Function Enable or Disable Smart Fan. The following system temperature, fan speed and voltage are monitored. Temperature:

 System Temperature  CPU Thermistor Temperature Fan Speed:  System Fan Speed  CPU Fan speed Voltage:  VCORE  +12V  +5V  +5VSB  AVCC  3VCC  VSB3  VBAT 3.6.2.7.1 Smart Fan Mode Configuration Item Options Description CPU Smart Fan Mode Manual Mode[Default] Mode 01/Mode 02/Mode 03/ Mode 04/Mode 05/Mode 06/ Mode 07/Mode 08/Mode 09/ Mode 10/Mode 11/Mode 10/ Mode 12/Mode 13/Mode 14/ Mode 15/Mode 16/Mode 17/ Mode 18/Mode 19/Mode 20 CPU Smart Fan Mode Select (Manual, Mode 1~ Mode 20). Fan PWM (0-255) 0-255[Default] Fan PWM duty (0-255).

Item Options Description Wake system from S5 Disabled[Default], Fixed Time Dynamic Time Enable or disable System wake on alarm event. Select Fixed Time, system will wake on the hr::min::sec specified. Select Dynamic Times, System will wake on the current time + Increase minute(s). Wake up day of week Disabled[Default], Monday-Friday Monday-Saturday Wake up day of week. (Monday-Friday) or (Monday-Saturday). Wake up hour 0-23 Select 0-23 For example enter 3 for 3am and 15 for 3pm. Wake up minute 0-23 Select 0-23 For example enter 3 for 3am and 15 for 3pm. Wake up second 0-23 Select 0-23 For example enter 3 for 3am and 15 for 3pm. Wake up minute increase 1-5 1-5.

3.6.2.9 Serial Port Console Redirection Item Options Description Console Redirection Enabled Disabled[Default] Console Redirection Enable or Disable. 3.6.2.10 SATA Configuration It allows you to select the operation mode for SATA controller.

Item Options Description SATA Controller(s) Enabled[Default] Disabled Enable or disable SATA Device. SATA Mode Selection IDE AHCI[Default] Determines how SATA controller(s) operate. SATA Controller Speed Default[Default] Gen1 Gen2 Gen3 Indicates the maximum speed the SATA controller can support. Port 0/1/4 Enabled[Default] Disabled Enable or Disable SATA Port. SATA Device Type Hard Disk Drive[Default] Solid State Drive Identify the SATA port is connected to Solid State Drive or Hard Disk Drive. 3.6.2.11 Thermal Configuration

3.6.2.11.1 Platform Thermal Configuration Item Option Description Critical Trip Point POR[Default] 80 C 90 C 100 C 110 C This value controls the temperature of the ACPI Critical Trip Point – the point in which the OS will shut the system off. Note: 100C is the Plan Of Record (POR) for all Intel mobile processors. Passive Trip Point Disabled 80 C 90 C[Default] 100 C 110 C This value controls the temperature of the ACPI Passive Trip Point – the point in which the OS will begin throttling the processor. Passive TC1 Value 1 – 16 1[Default] This value sets the TC1 value for the ACPI Passive Cooling Formula. Range 1 – 16. Passive TC2 Value 1 – 16 5[Default] This value sets the TC1 value for the ACPI Passive Cooling Formula. Range 1 – 16. Passive TSP Value 2 – 32 10[Default] This item sets the TSP value for the ACPI Passive Cooling Formula. It represents in tenths of a second how often the OS will read the temperature when passive cooling is enabled. Range 2 – 32.

3.6.2.12 Network Stack Item Option Description Network stack Enabled Disabled[Default] Enable/Disable UEFI Network Stack. Ipv4/6 PXE Support Enabled[Default] Disabled Enable Ipv4/6 PXE Boot Support. If disabled IPV4/6 PXE boot option will not be created. PXE boot wait time 0 Wait time to press ESC key to abort the PXE boot. Media detect count 1 Number of times presence of media will be checked.

3.6.2.13 CSM Configuration Item Option Description CSM Support Enabled[Default] Disabled Enable/Disable CSM Support. GateA20 Active Upon Request[Default] Always UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Messages Force BIOS Keep Current[Default] Set display mode for Option ROM. Boot option filter UEFI and Legacy[Default] Legacy only UEFI only This option controls Legacy/UEFI ROMs priority. Network Do not launch[Default] UEFI Legacy Controls the execution of UEFI and Legacy PXE OpROM. Storage Do not launch UEFI Legacy[Default] Controls the execution of UEFI and Legacy Storage OpROM. Video Do not launch UEFI Legacy[Default] Controls the execution of UEFI and Legacy Video OpROM. Other PCI devices Do not launch UEFI[Default] Legacy Determines OpROM execution policy for devices other than Network, Storage, or Video.

3.6.2.14 USB Configuration The USB Configuration menu helps read USB information and configures USB settings. Item Options Description Legacy USB Support Enabled[Default] Disabled Auto Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. XHCI Hand-off Enabled[Default] Disabled This is a workaround for OSew without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. EHCI Hand-off Enabled Disabled[Default] This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. USB Mass Storage Driver Support Enabled[Default] Disabled Enable/Disable USB Mass Storage Driver Support. Mass Storage Devices Auto[Default] Floppy Forced FDD Hard Disk CD-ROM Mass storage device emulation type. ‘AUTO’ enumerates devices according to their media format. Optical drives are emulated as ‘CDROM’, drives with no media will be emulated according to a drive type.

3.6.3 Chipset 3.6.3.1 System Agent (SA) Configuration Item Options Description VT-d Enabled[Default] Disabled Check to enable VT-d function on MCH.

3.6.3.1.1 Graphics Configuration Item Options Description Aperture Size [128MB] [256MB] [Default] [512MB] [1024MB] Select the Aperture Size. Note: Above 4GB MMIO BIOS assignment is automatically enabled when selecting 2048 aperture. To use this feature, please disable CSM Support. DVMT Pre-Allocated [32M] [Default] [64M] [96M] [128M] [160M] [192M] [224M] [256M] [288M] [320M] [352M] [384M] [416M] [448M] [480M] [512M] [1024M] Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem [128M] [256M] [Default] [MAX] Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device. Gfx Low Power Mode Enabled[Default] Disabled This option is applicable for SFF only.

3.6.3.1.1.1 LCD Control Item Option Description Primary IGFX Boot Display VBIOS Default[Default] CRT HDMI-1 LVDS DVI HDMI-2 Select the Video Device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. Active LFP No LVDS eDP Port-A[Default] Select the Active LFP Configuration. No LVDS:VBIOS does not enable LVDS. Int-LVDS. Int-LVDS:BIOS enables LVDS driver by Integrated encoder. SDVO LVDS:VBIOS enables LVDS driver by SDVO encoder. eDP Port-A:LFP Driven by Int-DisplayPort encoder from Port-A. eDP Port-D:LFP Driven by Int-DisplayPort encoder from Port-D9through PCH). CH7511 EDID Panel Option 1024x768 24/1[Default] 800x600 18/1 1024x768 18/1 1366x768 18/1 1024x600 18/1 1280x800 18/1 1920x1200 24/2 640x480 18/1 800x480 18/1 1920x1080 18/2 Port-EDP to LVDS (Chrotel7511) Panel EDID Option.

1280x1024 24/2 1440x900 18/2 1600x1200 24/2 1366x768 24/1 1920x1080 24/2 1680x1050 24/2 Backlight brightness (%) 0% 25% 50%[Default] 75% 100% Select LVDS back light PWM duty. LVDS Back Light PWM Frequency 200 Hz[Default] 300 Hz 400 Hz 500 Hz 700 Hz 1 kHz 2 kHz 3 kHz 5 kHz 10 kHz 20 kHz Select LVDS back light PWM Frequency. 3.6.3.1.2 Memory Configuration

Item Options Description Max TOLUD Dynamic[Default] 1 GB 1.25 GB 1.5 GB 1.75 GB 2 GB 2.25 GB 2.5 GB 2.75 GB 3 GB 3.25 GB Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller. 3.6.3.2 PCH-IO Configuration Item Options Description PCH LAN Controller Enabled[Default] Disabled Enable or disable onboard NIC. Mini PCIe WLAN Enable Enabled Disabled[Default] Only effected on Mini PCIe with WLAN adapter.

3.6.3.2.1 PCI Express Configuration 3.6.3.2.1.1 PCI Express Root Port 1 Item Option Description PCI Express Root Port 1 Enabled[Default] Disabled Control the PCI Express Root Port. ASPM Support Disabled Set the ASPM Level: Force L0s – Force

L0s L1 L0sL1 Auto[Default] all links to L0s State AUTO – BIOS auto configure DISABLE – Disables ASPM. PCIe Speed Auto[Default] Gen1 Gen2 Select PCI Express port speed. 3.6.3.2.2 USB Configuration Item Options Description USB Precondition Enabled[Default] Disabled Precondition work on USB host controller and root ports for faster enumeration. XHCI Mode Smart Auto Auto[Default] Enabled Disabled Mode of operation of xHCI controller. USB Ports Per-Port Disable Control Enabled Disabled[Default] Control each of the USB ports (0~13) disabling.

3.6.3.2.3 PCH Azalia Configuration Item Options Description Azalia Disabled Enabled[Default] Auto Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be unconditionally Enabled. Auto = Azalia will be enabled if present, disabled otherwise. 3.6.3.2.4 BIOS Security Configuration

Item Options Description BIOS Lock Disabled[Default] Enabled Enable or disable BIOS lock enable (BLE) bit. 3.6.4 Security  Administrator Password Set setup Administrator Password  User Password Set User Password

3.6.4.1 Secure Boot menu Item Options Description Secure Boot Enabled Disabled[Default] Secure Boot can be enabled if 1.System running in User mode with enrolled Platform Key (PK) 2.CSm function is disabled. Secure Boot Mode Standard Custom[Default] Secure Boot mode selector. ‘Custom’ Mode enables users to change Image Execution policy and manage Secure Boot Keys. 3.6.4.1.1 Key Management

Item Options Description Default Key Provision Disabled[Default] Enabled Install Factory default Secure Boot Keys when System is in Setup Mode. 3.6.4 Boot Item Option Description Setup Prompt Timeout 1~ 65535 Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State On[Default] Off Select the Keyboard NumLock state. Quiet Boot Disabled[Default] Enabled Enables or disables Quiet Boot option. Fast Boot Disabled[Default] Enabled Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options. Boot Option #1/2 Sets the system boot order

3.6.6 Save and Exit 3.6.6.1 Save Changes and Reset Reset the system after saving the changes. 3.6.6.2 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are discarded. The setup program then exits and reboots the controller. 3.6.6.3 Restore Defaults This option restores all BIOS settings to the factory default. This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS setting.

4. Drivers Installation Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen.

4.1 Install Chipset Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Chipset\Intel\ECM-BDWH. Note: The installation procedures and screen shots in this section are based on Windows 8 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step1. Click Next.. Step 4. Click Finish to complete setup. Step 2. Click Accept.

4.2 Install ME Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Utility\ECM-BDWH_ME. Note: The installation procedures and screen shots in this section are based on Windows 8 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Next to proceed setup. Step1. Click Next to start installation. Step 4. Click Finish to complete setup. Step 2. Click Next.

4.3 Install USB 3.0 Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Utility\ECM-BDWH_USB 3.0. Note: The installation procedures and screen shots in this section are based on Windows 7 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Next to continue installation. Step1. Click Next to start installation. . Step 4. Click Next to continue installation. Step 2. Click Yes. Step 5. Click Finish to complete setup.

4.4 Install VGA Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \VGA\ECM-BDWH. Note: The installation procedures and screen shots in this section are based on Windows 8 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Next. Step 2. Click Yes to accept license agreement. Step 5. Click Finish to complete setup. Notice: Owing to the first priority of display is LVDS, it occur two screens (VGA + HDMI Monitor) disappears after install the OS & VGA driver at first time. Please unplug the HDMI Cable and then continue installing Driver, the Monitor can be working normally.

4.5 Install Audio Driver (For Realtek ALC892) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Audio\Realtek\ALC892\ECM-BDWH_Audio. Note: The installation procedures and screen shots in this section are based on Windows 8 operation system. Step 1. Click Next to continue setup. Step 2. Click Finish to complete the setup.

4.6 Install Ethernet Driver (For Intel I210AT and I217LM) Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Gigabit\Intel\I210AT_I217LM\ECM-B DWH_LAN. Note: The installation procedures and screen shots in this section are based on Windows 8 operation system. Step 3. Click Next. Step 1. Click Next. Step 4. Click Install to proceed. Step 2. Click Next to accept license agreement. Step 5. Click Finish to complete the setup.