Briteq VP-P37.5 Preliminary Setup Instructions

Mechanical screen assembly - Put the screen together using the quick lock adapters o Always fix the “VP-P37.5 BRACKET” first: suspended to the ceiling or truss construction.  Make sure that the ceiling/truss construction can support the complete screen!  Each bracket can support a column of up to 10 panels. (screen height = 6m) o Fix the panels in rows: first install 2 rows before you start lock the upper row. This makes it easier to build the screen together. Electrical screen assembly Please refer to the drawing: The drawing shows the screen from the BACKSIDE! This means that you should place yourself on the backside of the screen and follow the instructions below: - Data (video signal) is cabled horizontally: always from left to right, starting from the top row! o The VP-SCANBOX has 8 outputs:  Output 1 is connected to the most left panel of the upper row. (panel1 on the drawing)  Output 2 is connected to the most left panel of the 2nd row. (panel8 on the drawing) o If the screen is too big for 1 scan box, you can easily connect several scan boxes together, using the RJ45 in/out connectors and the (blue) CAT6-cable. Configuration of the setup is done in the setup software. o Use the small 30cm data cables to daisy chain panels in a row. Note: VP-SCANBOX supports theoretically up to 12panels (192pixels) per output but to have good performance you should limit this number to max. 8 panels per output. (ideal = 5 to 6 panels) - Power (230Vac) is cabled vertically: always from bottom to top. o Use the small 30cm power cables to daisy chain panels in a column. Note: a special power cable (VP-POWERLINE 4/30P) is available: it has a length of 4m and has 4 outputs so you can connect 4 colums and up to 30 panels. Interface assembly You need a Windows PC (or laptop) + “VP-PC INTERFACE” + one or more “VP-SCANBOX” to setup the interface with the screen. - PC  VP-PC INTERFACE: 2 lines are needed: o USB line: use the supplied USB-cable. Important! Before you connect the VP-PC INTERFACE to your PC, you should install the USB-drivers! (see attached file with drivers)

your PC only has VGA output, you will need a USB/DVI-converter. In fact this is an external video card which converts USB signals to DVI. (possible supplier: www.manhattan- products.com “hi-speed USB2.0 to DVI converter”) - VP-PC INTERFACE  VP-SCANBOX: 1 CAT6-cable can be connected between the U-sender output of the VP-PC INTERFACE and the RJ45 input of the VP-SCANBOX. This cable can reach a length up to 100m. Software setup - Insert the CDROM: a window pops up  choose “installing LED play software” - Select ENGLISH as installation language - Registration information: o Name: put your name o Company: put the name of the venue or your company. o Serial: just put key in  888888 - Press the “next” button  software will be installed. - Start LED STUDIO program - Open the OPTION menu and select “Software setup”  a new window opens. - Put the cursor (Windows arrow) somewhere in this new window (but NOT in a data input filed!) and press linsn (you will hear some noises while typing this word)  a password window opens. - Please insert the password 168 and press the OK button. - In the new window (setup hardware parameters): choose the option “RECEIVER” on the top. - On the bottom press the button “LOAD FROM FILES” and load the file “p37.5R.RCG” (configuration file, supplied with the screen)  on the upper right of the window you will see the name of the file appearing. (see picture on the right) - Just below, please change the option “gray level” to “Hi-brightness 512” (or Hi-brightness 256”) - On the second part of the window

the complete screen in pixels!!! - One P37.5 panel measures 16x16 pixels so for our example screen you will have the following data: o Width: 7panels x 16 pixels = 7 x 16 = 112pixels  fill in “112” for width o Height: 5panels x 16 pixels = 5 x 16 = 80pixels  fill in “80” for height  Fill in the exact data for your screen and press the button “SEND TO RECEIVER”: in the new window select ALL and press OK.  When everything works well, you still have to save the settings permanently to the scan box. To do this, press the “SAVE TO RECEIVER” button: in the new window select ALL and press OK. - Now in the window (setup hardware parameters): choose the option “DISPLAY CONNECTION” on the top.  the window on the right appears. - When only 1 VP-SCANBOX is used, make sure that “Horizontal card” is set to 1 and also “Vertical card” is set to 1.  One pink box (representing the scan box) appears. - Press the pink box until it turns grey and you are able to configure it on the bottom of the window, fill in: o Main cable: 1 No sender U o Extension cable: 1 o Order No: 1 o Width: width of the screen in pixels (example: 112) o Height: heigth of the screen in pixels (example: 80) - Press “SEND TO RECEIVER” button to send the data to screen. - When everything works well, you still have to save the settings permanently to the scan box. To do this, press the “SAVE TO RECEIVER” button - Press EXIT button until come back to the main screen of the program. Location of the screen capture area: The screen works simply by sending the contents (copy) of a portion of your PC-screen to the video screen. So the output of any program you drag in this area will be shown on the screen. Of course you need to know which part of the screen is copied to the screen. To make this part visible, do the following: - Open the Option screen and select “Screen area (Y)”  a small part of the screen is marked by a red square. All windows dragged inside this square will be copied to the video screen. - On the bottom of this window you can choose to put the square permanently on the screen: easy to find the captured screen area. Please note that this is a first draft which is not finished yet, we apologize for any inconvenience caused.