Campbell COM9602 Instruction Manual

Data Modem September 2016 Copyright © 2016 Campbell Scientific (Canada) Corp.

This equipment is warranted by CAMPBELL SCIENTIFIC (CANADA) CORP. ("CSC") to be free from defects in materials and workmanship under normal use and service for twenty-four (24) months from date of shipment unless specified otherwise. ***** Batteries are not warranted. ***** CSC's obligation under this warranty is limited to repairing or replacing (at CSC's option) defective products. The customer shall assume all costs of removing, reinstalling, and shipping defective products to CSC. CSC will return such products by surface carrier prepaid. This warranty shall not apply to any CSC products which have been subjected to modification, misuse, neglect, accidents of nature, or shipping damage. This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for a particular purpose. CSC is not liable for special, indirect, incidental, or consequential damages. Products may not be returned without prior authorization. To obtain a Return Merchandise Authorization (RMA), contact CAMPBELL SCIENTIFIC (CANADA) CORP., at (780) 454-2505. An RMA number will be issued in order to facilitate Repair Personnel in identifying an instrument upon arrival. Please write this number clearly on the outside of the shipping container. Include description of symptoms and all pertinent details. CAMPBELL SCIENTIFIC (CANADA) CORP. does not accept collect calls. Non-warranty products returned for repair should be accompanied by a purchase order to cover repair costs.

TRIPODS, TOWERS, AND ANY ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES, ANTENNAS, ETC. FAILURE TO PROPERLY AND COMPLETELY ASSEMBLE, INSTALL, OPERATE, USE, AND MAINTAIN TRIPODS, TOWERS, AND ATTACHMENTS, AND FAILURE TO HEED WARNINGS, INCREASES THE RISK OF DEATH, ACCIDENT, SERIOUS INJURY, PROPERTY DAMAGE, AND PRODUCT FAILURE. TAKE ALL REASONABLE PRECAUTIONS TO AVOID THESE HAZARDS. CHECK WITH YOUR ORGANIZATION'S SAFETY COORDINATOR (OR POLICY) FOR PROCEDURES AND REQUIRED PROTECTIVE EQUIPMENT PRIOR TO PERFORMING ANY WORK. Use tripods, towers, and attachments to tripods and towers only for purposes for which they are designed. Do not exceed design limits. Be familiar and comply with all instructions provided in product manuals. Manuals are available at www.campbellsci.ca or by telephoning (780) 454-2505 (Canada). You are responsible for conformance with governing codes and regulations, including safety regulations, and the integrity and location of structures or land to which towers, tripods, and any attachments are attached. Installation sites should be evaluated and approved by a qualified personnel (e.g. engineer). If questions or concerns arise regarding installation, use, or maintenance of tripods, towers, attachments, or electrical connections, consult with a licensed and qualified engineer or electrician. General  Prior to performing site or installation work, obtain required approvals and permits.  Use only qualified personnel for installation, use, and maintenance of tripods and towers, and any attachments to tripods and towers. The use of licensed and qualified contractors is highly recommended.  Read all applicable instructions carefully and understand procedures thoroughly before beginning work.  Wear a hardhat and eye protection, and take other appropriate safety precautions while working on or around tripods and towers.  Do not climb tripods or towers at any time, and prohibit climbing by other persons. Take reasonable precautions to secure tripod and tower sites from trespassers.  Use only manufacturer recommended parts, materials, and tools. Utility and Electrical  You can be killed or sustain serious bodily injury if the tripod, tower, or attachments you are installing, constructing, using, or maintaining, or a tool, stake, or anchor, come in contact with overhead or underground utility lines.  Maintain a distance of at least one-and-one-half times structure height, 6 meters (20 feet), or the distance required by applicable law, whichever is greater, between overhead utility lines and the structure (tripod, tower, attachments, or tools).  Prior to performing site or installation work, inform all utility companies and have all underground utilities marked.  Comply with all electrical codes. Electrical equipment and related grounding devices should be installed by a licensed and qualified electrician. Elevated Work and Weather  Exercise extreme caution when performing elevated work.  Use appropriate equipment and safety practices.  During installation and maintenance, keep tower and tripod sites clear of un-trained or non- essential personnel. Take precautions to prevent elevated tools and objects from dropping.  Do not perform any work in inclement weather, including wind, rain, snow, lightning, etc. Maintenance  Periodically (at least yearly) check for wear and damage, including corrosion, stress cracks, frayed cables, loose cable clamps, cable tightness, etc. and take necessary corrective actions.  Periodically (at least yearly) check electrical ground connections. WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS, THE CLIENT ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES, ANTENNAS, ETC.

PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to specific sections. 1. Introduction ................................................................ 1 2. Cautionary Statements .............................................. 1 3. Initial Inspection ......................................................... 2 4. Overview ..................................................................... 2 4.1 Data Services........................................................................................................... 3 4.2 Modem and Accessories .................................................................................... 3 5. Specifications ............................................................. 5 6. Installation .................................................................. 5 6.1 Antenna ..................................................................................................................... 5 6.2 Modem ....................................................................................................................... 7 6.3 Datalogger Configuration .................................................................................. 7 6.4 Datalogger Wiring ............................................................................................. 10 6.5 Power Control ..................................................................................................... 10 6.6 Programming ....................................................................................................... 11 7. Troubleshooting ....................................................... 14 Appendix A. CSC EU Declaration of Conformity ..... A-1 EU Declaration of Conformity ....................................... A-1 Figures Figure 6-1 Antenna, Mount, and Cable ...................................................................... 6 Figure 6-2 Antenna Attached to Mount ..................................................................... 6 Figure 6-3 Device Configuration Utility ................................................................... 8 Figure 6-4 File Control Tab ............................................................................................. 8 Figure 6-5 Run Options .................................................................................................... 9 Figure 6-6 Data Monitor Tab.......................................................................................... 9 Tables Table 4-1 COM9602 Modem & Interface Kit Equipment List .......................... 4 Table 6-1 Campbell Scientific Datalogger Connections .................................. 10