Comcater COMENDA Hi-Line HC Series Instructions For Use And Maintenance Manual

In the presence of hard water, limestone deposits are formed inside the machine and on the dishes which, for hygienic and operational purposes, must be removed by descaling. The operating procedures and their frequency are usually recommended by the supplier of the descaler who has ap- propriate products. To avoid damaging the machine, do not exaggerate the dosages, strictly abiding by the instructions of the descaler manufacturer. When the operations have finished, rinse with plenty of water 2.5. PUTTING TEMPORARILY OUT OF SERVICE. In case of a prolonged stop of a few week ...

1.1 GENERAL DESCRIPTION Single skin body, stainless steel execution AISI 304. Single piece deep drawn tank with multiple filtering sy- stem (pump suction, collection filter and micro-filter) with presence indicator. Upper and lower stainless steel wash and rinse arms. Self draining wash pump. Hood activated cycle start and manual cycle start. removable rack holder. Self-cleaning cycle at unit switch-off. Upper control panel. Self draining wash pump. Built in HR drain pump. Electro- nic adjustment of the detergent and rinse aid dispenser. 1.2 TY ...

ENGLISH 2.2. CLEANING (Fig. 8) 2.2. a General Strict observance of the maintenance rules in this section guarantees good preservation and satisfac- tory operation of the machine and greatly reduces the need for repairs. ATTENTION In case of irregularities or malfunctioning of any com- ponent of the machine, FIRST OF ALL CHECK that the instructions in the previous paragraphs have been followed. Interventions must be carried out promptly at the onset of failures to avoid worsening of the problem and damaging further parts. ATTENTION Daily operations to be carrie ...

ENGLISH Part 2: Reserved for Operator MACHINE STATUS START KEY COLOUR Machine OFF none GREEN (steady) BLUE (steady) Machine in FILLING phase TANK WATER LEVEL reached START START GREEN (flashing) BOILER and TANK WATER TEMPERATURE reached Machine in ALARM START START RED (steady) START START CYCLE in PROGRESS (machine READY) START START Machine in manual REGENERATION WHITE (steady) ORANGE (steady) START START START START START START ...

2.9 REGENERATION CYCLE HC-HCXL 2.9.a FILLING THE SALT TANK IMPORTANT The tank is to be filled when alarm F4 appears on the display. First of all make sure that there is salt in the specific con- tainer and proceed as follows: 1. Unscrew the cap of the salt tank and introduce coarse kitchen salt. 2. Screw the plug back on all the way to make sure the tank is sealed. 2.9.c MANUAL REGENERATION OPERATIONS (at the user’s discretion) With the machine ON, perform the following operations: 2.9.b RESIN REGENERATION OPERATIONS (AUTOMATIC) (only for mod. " RA" ...

THE OPERATOR - Before commissioning the machine, the operator must have carefully read this publication and acquired an in depth knowledge of the technical specifications and of the machine controls. - Before installing the machine, check that the installation site is compatible with its overall dimensions. - If the machine is “recessed”, make sure that the compartment and adjacent furnishing elements are suitable, namely that they do not suffer from being exposed to the water vapour which can escape the machine during operation and especially when the door opens af ...

ENGLISH 2.2. CLEANING (Fig. 8) 2.2. a General Strict observance of the maintenance rules in this section guarantees good preservation and satisfac- tory operation of the machine and greatly reduces the need for repairs. ATTENTION In case of irregularities or malfunctioning of any com- ponent of the machine, FIRST OF ALL CHECK that the instructions in the previous paragraphs have been followed. Interventions must be carried out promptly at the onset of failures to avoid worsening of the problem and damaging further parts. ATTENTION Daily operations to be carrie ...

Allumage/Arrêt (ON/OFF) Démarrage du cycle sélectionné Schalter (AN/AUS) Zyklus Starte START START Scroll/Selection Key Touche Défi lement/Sélection Taste Scroll und Wahl Back Key Touche BACK Zurück-Taste Accensione/Spegnimento (ON/OFF) Avvio ciclo selezionato Ligar / desligar (ON/OFF) Ativação ciclo selecionado Tecla deslocação/Seleção Tecla BACK Ecrã CRUSCOTTO COMANDI - CONTROL PANEL - PANNEAU DES COMMANDES SCHALTBLENDE - PANEL DE MANDOS - PAINEL DE ...