CHIEF PAC-252 Installation Instructions Manual

and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components does not exceed the maximum weight capacity of the mount to which this accessory is being installed.

Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme Open-Ended Wrench Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche Hex-Head Wrench Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale Pencil Mark Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Optional Opcional Optional Opcional Opzionale Optie En option Security Wrench Llave de seguridad Sicherheitsschlüssel Chave de segurança Chiave di sicurezza Veiligheidssleutel Clé de sécurité

PARTS 1/8" (included) 5/32" (included) A (1) B (2) C (6) D (4) E (4) F (8) 10-24x3/8" G (4) 10-24x7/8" H (4) 10-24x3/8" I (8) 10-24x3/8" J (1) 1/8" K (1) 5/32" Phillips

1. Using a 10-24 button head cap screw (G) inserted from inside of bracket, secure mounting button (E), with chamfered hole of mounting button (larger surface) facing bracket, to bracket. Repeat with other three mounting buttons. (See Figures 1 & 2) Figure 1 Figure 2 2. Attach large bumpers (D), making sure the CPU will rest against the bumpers when installed. (See Figures 3 & 4) Figure 3 Figure 4

against the bumpers when installed. (See Figures 5 & 6) Figure 5 Figure 6 4. Turn adapter on its end. (See Figure 7) 5. If necessary, slide brackets out of the way before installing the CPU inside adapter. 6. Install the CPU Inside adapter. 7. Adjust side brackets until they firmly press against sides and top of CPU. 8. while pressing brackets against CPU, tighten all Nylock nuts. The CPU should now be completely rigid inside of adapter. Figure 7 9. Using 10-24 pan head Phillips or button head security screws (I or H), secure side covers. (See Figure 8) Figure 8 10. Lift Interface Adapter (A) up to Chief Mount, aligning buttons (E) of adapter with slots in the Chief Mount. Make sure the tear drop slots of Interface Adapter (A) face down replicating those of the Chief Mount. 11. Raise safety latch on Chief Mount to secure Display, making sure latch is completely engaged. 12. With the aid of another person, lift Large Flat Panel Display up to the PAC-252 CPU Interface Adapter (A), aligning buttons of mounting brackets with slots in adapter. 13. Raise safety latch on PAC-252 to secure Display, making sure latch is completely engaged. Safety latch

P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477 Chief Manufacturing, a products division of Milestone AV Technologies 8832-000081 Rev 01 ¤2010 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 08/10