CommScope 639849 Instruction Sheet

6 M8 screw 2 3 · Bracket edges parallel to each other. (fully collapsed position) Pre-assembly of Downtilt Brackets by Kit Vendor 7 ITEM NO. DESCRIPTION BSAMNT-4 QUANTITY BSAMNT-M4 QUANTITY 1 PIPECLAMP BRACKET, NO FLANGE 4 2 2 BRACKET,NOTCHED 1 1 3 BRACKET 1 1 4 PLATE, TWO HOLES 2 2 5 BRACKET, PIPE CLAMP INTERFACE 2 1 6 SCR,HH,HEX,M8X25,SST,PASS 2 2 7 WSHR,LK,SPLT,M8,STL,GALV 2 2 8 SCR,HH,HEX,M10X25,SST,PASS 2 2 9 NUT,HEX,M10,STL,GALV 12 8 10 WSHR,LK,SPLT,M10,STL,GALV 8 6 11 SCR,HCS,HEX,M10X40,STL,GALV 6 4 12 NUT,HEX,M12-1.75,STL,GALV 12 6 13 WSHR,FLT,M12,13X24X2.5,STL,GALV 4 2 14 WSHR,LK,SPLT,M12,STL,GALV 4 2 15 BOLT,CARRIAGE,M12X200,STL,GALV 4 2 Mounting Kits For Wide Panel Antennas BSAMNT-4, BSAMNT-M4: Mounting systems for cylindrical pipe installations (60-115 mm pipe diameter) for heavy duty applications This document explains how to install an antenna using a BSAMNT mount kit. Antennas with two mount points will use BSAMNT-4. Antennas with three mount points will also use BSAMNT-M4. 639849 Revision D, August 2019 Page 1 of 5 www.commscope.com © 2019 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639849 D (08/19)

(BSAMNT-4 QTY 2 EA) (BSAMNT-M4 QTY 1 EA) Pre-assembly of Downtilt Brackets by Field Installer 8 M10 screw · Bracket edges parallel to each other. (fully collapsed position) 10 MAXIMUM TORQUE M12 58N.m (43ft.lbs) 639849 Page 2 of 5 www.commscope.com © 2019 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639849 D (08/19)

Top / Middle Mount Installations 12 14 13 11 1 M10 screw 1 13 14 12 11 M10 SCREW 11 M10 SCREW CRITICAL: For initial installation to pipe, downtilt brackets must be configured in pre-assembly position (fully collapsed). 10 9 10 9 10 9 WARNING: LOOSENING OR REMOVING BOLTS THAT ATTACH MOUNTING PLATE TO ANTENNA WILL VOID WARRANTY AND MAY RESULT IN PRODUCT DAMAGE OR PERSONAL INJURY. WARNING: LOOSENING OR REMOVING BOLTS THAT ATTACH MOUNTING PLATE TO ANTENNA WILL VOID WARRANTY AND MAY RESULT IN PRODUCT DAMAGE OR PERSONAL INJURY. MAXIMUM TORQUE M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs) MAXIMUM TORQUE M8 15N.m (11ft.lbs) M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs) 639849 Page 3 of 5 www.commscope.com © 2019 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639849 D (08/19)

not remove) • Remove adjuster screws. • Adjust antenna angle. (use inclinometer) • Reinstall adjuster screws. Middle Bracket First • Retighten all screws. Adjusting Antenna Tilt - 3 POINT MOUNT M10 pivot screw (loosen only) M10 pivot screw (loosen only) A M10 pivot screw (loosen only) M8 adjuster screw perimeter location (remove to adjust tilt) M10 pivot screw center location (loosen only) M10 pivot screw (loosen only) DETAIL A M10 pivot screw (loosen only) M10 pivot screw (loosen only) A Adjusting Antenna Tilt - 2 POINT MOUNT • Loosen pivot screws . (do not remove) • Remove adjuster screws. • Adjust antenna angle. (use inclinometer) • Reinstall adjuster screws. • Retighten all screws. DETAIL A M10 pivot screw (loosen only) M8 adjuster screw perimeter location (remove to adjust tilt) M10 pivot screw center location (loosen only) A use inclinometer to adjust antenna angle use inclinometer to adjust antenna angle M10 pivot screw (loosen only) MAXIMUM TORQUE M8 15N.m (11ft.lbs) M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs) MAXIMUM TORQUE M8 15N.m (11ft.lbs) M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs) 639849 Page 4 of 5 www.commscope.com © 2019 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639849 D (08/19)

requires qualified, experienced personnel. CommScope installation instructions are written for such installation personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. CommScope disclaims any liability or responsibility for the results of improper or unsafe installation practices. It is recommended that transmit power be turned off when the field installation is performed. Follow all applicable safety precautions as shown on this page. Do not install on a wet or windy day or when lightning or thunder is in the area. Do not use metal ladder. Do not install near power lines. Power lines, telephone lines, and guy wires look the same. Assume any wire or line can electrocute you. Wear shoes with rubber soles and heels. Wear protective clothing including a long-sleeved shirt and rubber gloves. A Remote Electrical Tilt Connection The AISG connector fitted to the antenna is designed to accept any AISG compliant cable assembly, commscope recommends hand tightening AISG mating connector only. Applied torque to the connector shall not exceed 1.5N*m. RF Cable Connection The female RF connectors fitted to the antenna are designed to fit jumper cables with standard related male RF connector. Tighten the RF connector coupling according to torque specification in antenna label, if the RF connectors are tightened beyond the recommend torque, the RF connection to the antenna may be damaged. 639849 Page 5 of 5 www.commscope.com © 2019 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639849 D (08/19)