Digilock numeris aspire Installation Manual

Download Digilock numeris aspire PDF Manual (16 pages)

Text of the manual

Before Lock Installation ��3 Surface Mount Installation For door thickness measuring between .16” - .91” (4 mm - 23 mm) Required Components��4 Installation��5 For door thickness measuring between .01" - .16" (0.2mm - 4 mm) Required Components��7 Installation��8 Door Preparation Strike Plate Installation Required Components��10 Installation��11 Door Mounting Holes Drill Instructions and Template Drill Instructions��12 Template for Standard & Vertical Body��13 Metal Door Preparation Compatibility Guide ��14 Removal of 3-hole Lock Plug��14 Removal of Padlock Hasp��15

The door must have door mounting holes.

Door Mounting Holes The door must be prepared for lock installation. Before Lock Installation 1. A strike plate must be installed. Strike Plate Angled Strike Plate Security Strike Plate Recommended for latch products Double Door Strike Plate 1 2 1 - Legacy Rear Units This installation guide is compatible for 4G Motorized Rear Units Deadbolt - Cable Deadlatch - Cable Deadbolt - Cable Deadlatch - Cable

For door thickness measuring between .16" - .91" (4 mm - 23 mm)

Required Components 1*- Phillips Head Screwdriver (#2) *Not included 2 - Phillips Head Screws D C B A Screw Size Length Door Thickness Min Max A 1" (25.400 mm) .01" (.2 mm) .16" (4 mm) B 1 1/4" (31.750 mm) .16" (4 mm) .43" (11 mm) C 1 1/2" (38.100 mm) .43" (11 mm) .67" (17 mm) D 1 3/4" (44.450 mm) .67" (17 mm) .91" (23 mm) 2 - Split Lock Washers Surface Mount Installation Tab Text Standard Keypad Vertical Body Touch RFID Vertical Body Touch RFID Standard Body Standard Keypad Standard Body 1 - Rear Units Deadbolt - Cable Deadlatch - Cable

With the rear unit behind the door, extend the cable through the door’s mounting hole.

Installation For illustration, a keypad front unit with a bolt rear unit is used. REAR VIEW FRONT VIEW 3 Hold the front and rear units against the door and secure with the mounting screws. Ensure the remaining cable is not pinched. REAR VIEW FRONT VIEW 2 Orient the cable with the red wire position on the top of the ribbon (see fig-1). Attach the cable to the front unit using the corresponding channel guides to ensure the snap connector is properly secured. Once connected a triple beep indicates successful connection. fig.-1

Repeat test with the door closed.

If ten rapid beeps are heard, the strike plate or door alignment may need adjustment to allow the lock to operate properly. If the door does not lock when the bolt/latch is extended, the strike plate or lock position may need adjustment. For keypad locks with deadbolt rear units: Press = ` to extend the bolt. Press = ` again to retract the bolt. For keypad locks with deadlatch rear units: Press = ` to retract the latch. The latch will extend automatically. For touch RFID locks with deadbolt rear units: Touch ` to extend the bolt. Touch ` again to retract the bolt. For touch RFID locks with deadlatch rear units: Touch ` to retract the latch. The latch will extend automatically. REAR VIEW FRONT VIEW 4 Test the lock while the door is open to ensure that the bolt or latch is operating properly.

Surface Mount Installation

For door thickness measuring between .01” - .16” (0.2 mm - 4 mm) 1* - 3/8” Nut Driver *Not included 2 - Locking Nuts 1 - Rear Units Deadbolt - Cable Deadlatch - Cable Tab Text Standard Keypad Vertical Body Touch RFID Vertical Body Touch RFID Standard Body Standard Keypad Standard Body

Hold the front unit against the front of the door. Use the rear unit mounting holes as a guide, then slide the front and rear units together.

Make sure the connector pins align properly with the connector. If properly connected, a triple beep will be heard and the LED will flash three times. For illustration, a keypad front unit with a bolt rear unit is used. REAR VIEW FRONT VIEW 1 Insert the front unit screw posts through the door mounting holes. REAR VIEW FRONT VIEW 3 Insert the locking nuts on the screw posts and tighten using the ratchet/screw gun. Do not over tighten.

Repeat test with the door closed.

If ten rapid beeps are heard, the strike plate or door alignment may need adjustment to allow the lock to operate properly. If the door does not lock when the bolt/latch is extended, the strike plate or lock position may need adjustment. For keypad locks with deadbolt rear units: Press = ` to extend the bolt. Press = ` again to retract the bolt. For keypad locks with deadlatch rear units: Press = ` to retract the latch. The latch will extend automatically. For touch RFID locks with deadbolt rear units: Touch ` to extend the bolt. Touch ` again to retract the bolt. For touch RFID locks with deadlatch rear units: Touch ` to retract the latch. The latch will extend automatically. REAR VIEW FRONT VIEW 4 Test the lock while the door is open to ensure that the bolt/latch is operating properly.

Strike Plate Installation

Digilock numeris aspire Installation Manual

Text of the manual