Excalibur 1511 Quick Start Operation Manual

QUICK START OPERATION GUIDE 5-Button 2-Way LED Remote Start Systems QUICK START OPERATION GUIDE REPLACING YOUR REMOTE BATTERY STEPS REMOTE PART# BATTERY (QTY) 1) Find the part # on the back of the remote to identify the battery type. 2) Remove the screw from the back of the remote. 3) Gently pry the case halves apart to access & replace the batteries. 1511 CR2025 (2) 1412 CR2032 (1) SECURITY, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS FUNCTION BUTTON(S) LED CONFIRMATION NOTE Lock & Arm1 LED Flash + 1 Beep Security enabled systems will flash the status LED. Lock Only1 , LED Flash Ideal for occupied vehicles, RV’s, etc. Unlock & Disarm1 LED Flash + 2 Beeps If only driver’s door unlocks, press again to unlock all. Silent Arm/Disarm1 x 2 or w/o beeps System will toggle Arm/Disarm each time Disable Sensor1 , 1 Beep After Lock/Arm Sensors are disabled until Lock/Arm Trunk/Hatch Release For 3 Sec. LED Flash + 2 Beeps By default, the system will also disarm/unlock Panic1 or 3 Sec. Alarm Tone Doors will Lock or Unlock before panic. Register today at www.CarAlarm.com To activate/view your warranty & Download a complete operation guide. Copyright 2019 Omega Research & Development Technologies, Inc. QOM_5BUTLED2WAY_20190829 Scan to register & download the full operation guide at CarAlarm.com! /c/omegard /omegard Problems? Questions? Contact Customer Service: 800-554-4053 (toll free) | +1-770-942-9876 (outside USA) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna., Increase the separation between the equipment and receiver., Connect the equipment into an outlet on a circuit different from that to which the receiver is connected., Consult the dealer or an experienced radio/TV technician for help., Warning! Changes or modifi cations made to this equipment not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi cations to this equipment. Such modifi cations could void the user’s authority to operate the equipment. Remote Start/Security System Model: (Installer, write system model above) 1 4 PROGRAMMING REMOTES TO THE SYSTEM (UP TO 4) BEFORE YOU BEGIN: Have all remotes for the system at hand. 1) Turn the ignition key “ON” (do not start). 2) Press the valet button 5 times within 5 seconds of step 1. - The siren/horn may briefly sound 3) Press & release the “lock” button on each transmitter one after the other. - 1-button models, press the “start” button. - The siren/horn may chirp once for each transmitter. - NOTE: When the fi rst remote is learned all previous remotes are erased. 4) Turn the ignition key “OFF”. - NOTE: The system will exit at any time after 10 seconds of no activity. SCAN TO WATCH HOW-TO VIDEO Visit www.CarAlarm.com today To Download your complete operation guide and learn more about system upgrades & other features! 1-Security related functions only available on some models. Consult your installer for more info.

QUICK START OPERATION GUIDE 5-Button 2-Way LED Remote Start Systems QUICK START OPERATION GUIDE REMOTE START FUNCTIONS FUNCTION BUTTON(S) LED CONFIRMATION NOTE Engine Start/Stop x 2 Flash + Melody Remote LED’s will flash to indicate remaning run time. 4 = 76-100% , 3 = 51-75%, 2 = 26-50%, 1 = 1-15%. The controller will beep when only 1 minute is remaining as an expiration warning. Run Time Extender2 All 4 LED’s will flash All 4 LED’s will flash to indicate restarting of the run timer (only allowed once per remote start cycle). Low Battery & Low/ Hi Temp Auto-Start , , 1 Beep Auto-start will activate a max of once per 2 hours and cancels when the ignition key is turned ON. See your installer or the full manual for threshold settings. Cabin Temperature P , 1-4 LEDs Flash + Melody 4 = Over 90F , 3 = 61-90F, 2 = 31-60F, 1 = Under 30F. Remote Valet2 , , + Melody This disables remote start and the security system. The status LED will turn on. Repeat this process or press valet button once to exit valet mode. FUNCTION VALET BUTTON NOTE Pit Stop Mode2 Press 2x w/ Engine On For More Than 10 Sec. (6x for XL mode) This will leave the engine running for the programmed run time (XL mode runs for 12 hours) so you can take your keys with you to run errands. OTHER 2-WAY CONTROLLER FUNCTIONS FUNCTION BUTTON(S) LED CONFIRMATION NOTE Status Update3 P , or Flash This confi rms the current Lock/Unlock status of the system/vehicle. CAR 2 Mode P , Flash + 2 Beeps To control a 2nd vehicle. Repeat to return to CAR 1 mode ( + 1 Beep). Low Car Battery Alert - 4 Beeps Alerts when battery level is below 11.5v for over 30 seconds. Out Of Range - All LED’s Flash When command response is not received P , + Flash CH3/AUX13 - Write Function In Function Column P x 2 , + Flash CH4/AUX23 - Write Function In Function Column P x 3 , + Flash CH5/AUX33 - Write Function In Function Column + + Flash AUX43 - Write Function In Function Column 2-WAY OPTIONS FEATURE PROCEDURE Beep Volume Hold P + for 1 second. Button Lock Hold P + for 1 second. TIP: If your system stops responding to your remote, make sure your aren’t accidentally in the wrong “Car” profi le. TROUBLE SHOOTING TIP: If remote start won’t activate, the system may be in valet mode (Status LED ON). Press the valet button once to exit. Status LED Valet / Programming Button WINDOW-MOUNT ANTENNA/RECEIVER 3 2 MANUAL TRANSMISSION RESERVATION MODE2 This must be performed before you can remote start a manual transmission vehicle to ensure the car is in neutral & maximum safety. Consult your installer for more information. 1) With the engine running by key (more than 10 seconds), hold the brake pedal & place the transmission in neutral. 2) Apply the parking brake and release the brake pedal. 3) Send the remote start command via your remote. The remote start should engage (LED flashing). 4) Take the ignition key out of the switch (the engine should stay running). 5) Exit the vehicle and lock your doors with the remote. The engine will turn off. Scan to register & download the full operation guide at CarAlarm.com! 2-These functions are only available on some remote start models. Consult your installer for more info. 3-These special functions may not be available on your vehicle. Consult your installer.