Flair AT07H2 Instruction Manual

Distribueret af: Folke-Larsens Eftf. A/S Ejby Industrivej 106 DK - 2600 Glostrup www.folkelarsen.dk

(A) Vinkelhoved med flere positioner. (B) Personlig udskiftelig farvering. (C) Momentregulering. (D) LED-lys. (E) LED-indikator. Synlig fra alle vinkler. (F) Omskifter mellem højre og venste omløbsretning. (G) Aftrækker og hastighedskontrol. (H) Stødabsorberende ergonomisk greb. ( I ) Batteritilslutning (J) Li-ion batteri. (K) Indgang til hastighedskontrol med kontrolboks (A) (C) (D) (G) (E) (J) (F) (K) (B) (H) (I)

(B) 1/4” bit tilslutning. (C) Personlig udskiftelig farvering. (D) Momentregulering (E) LED-lys (F) LED-indikatoer. Synlig fra alle vinkler (G) Aftrækker og hastighedskontrol. (H) Stødabsorberende ergonomisk greb. ( I ) Batteritilslutning (J) Li-ion batteri. (K) Indgang til hastighedskontrol med kontrolboks (G) Aftrækker og hastighedskontrol. - 3 - (B) (A) (D) (E) (H) (F) (K) (G) (L) (C) (I) (J)

Arbejdsområde - 4 - Hold arbejdsområdet rent og godt belyst. Rodede eller mørke områder indbyder til ulykker. Undlad at bruge maskinen i eksplosive atmosfærer som f.eks. ved forekomst af brænbare væsker, asarter eler stov. Ma- skinværktøj fremkalder ginister, som kan antænde støv eller dam- pe. Hold børn og tilskurer på af- tand. Forstyrrelser kan få dig til at miste herredømmet over værktø- jet. Personlig sikkerhed Vær agtpågivende, se på det, du gør og brug almindelig sund fornuft, når du betjener værktø- jet. Undlad at bruge maskiner, hvis du er træt eller påvirket af narkotika, alkohol eller medi- cin. Et øjebliks uopmærksomhed kan medføre alvorlig person- skade. Brug passende påklædning. Du må ikke bære smykker eller være iført løstsiddende tøj. Hold hår, tøj og handsker væk fra dele i bevæglese.. Løst tøj, smykker og langt hår kan blive viklet ind I dele I bevægelse.. Stræk dig ikke for langt frem. Sørg altid for, at have et sikkert fodfæste og en korrekt afba- lancering. Så har du bedre styr på værktøjet. Brug personlige værnemidler. Brug altid beskyttelsesbriller. Støvmaske, skridsikre sikkerheds- sko, beskyttelseshjelm og høreværn reducerer personskader. Brug og vedligeholdelse Brug skruetvingere eller lign. til at fastholde elementer til ar- bejdsbordet. Hold aldrig elementer I hånden. Undlad at bruge magt på værktø- jet. Brug det korrekte værktøj til dit arbejde. Det rigtige værktøj vil gøre arbejdet bedre og mere sikkert til den hastighed, som det er desig- net til. Undlad at bruge værktøjet, hvis aftrækkeren ikke tænder eller slukker det. Ethvert værktøj, som ikke kan styres med aftrækkeren, er farligt og skal repareres.. Opbevar ubenyttede maskiner uden for børns rækkevidde og lad ikke personer, som mangler kendskab til maskinen eller disse instrukioner betjene værktøjet. Maskiner er fralige i hænderne på uerfarne brugere. Kontroller om maskinen er skævt sammensat, om der er dele, som ikke bevæger sig, om der er brud på dele eller om der er andre for- hold, som kan påvirke værktøjets drift. Mange ulykker skyldes dårligt vedligeholdt værktøj.

Brug kun tilbehør, der anbefa- les af producenten. Tilbehør og bits, der passer til ‘et værktøj, kan være farligt at bruge på et andet værktøj. Service Få dit værktøj efterset af en kvalificeret reparatør, der kun burger originale reservedele. Dette vil sikre, at værktøjet forbliver sikker at bruge. Brug kun originale reservedele. Følg instruktionerne i afsnittet om vedligeholdelse. Brug af uoriginale reservedele og undla- delse af vedligeholdelse kan ud- løse elektrisk stød og personska- de. Yderligere sikkerhedsregler Batterilader Advarsel: Må kun bruges til det batteri, der er beregnet til maski- nen. Andre batterier kan eksplod- ere og være skyld i personskader. Læs instruktionerne og advarsler- ne på batteri og lader før batteri og lader tages i brug. Ladersen må ikke overdækkes. Laderen må ikke udsættes for regn, sne eller fugtige omgivelser. Træk ikke i ledningen, når du fjerner stikket fra stikkontakten. Brug af tilbehør, der ikke er anbe- falet af producenten, kan resultere i brand, elektrisk stød eller per- sonskade. Sørg for at ledningen til laderen ikke er til fare, så man kan falde i den eller træde på den, og således udsætter ledningen for skader. Brug ikke ledningen til laderen til at bære laderen. Sørg for ikke at skade ledningen til laderen på no- gen måde. Brug ikke laderen, hvis den er beskadiget eller hvis led- ningen er beskadiget. Tag laderen ud af stikkontakten inden du foretager vedligeholdelse eller nogen form for reparation på laderen. Undlad at skille laderen og batteri- holderen ad. Laderen skal service- res af en autoriseret elektriker. Forkert samling af lader kan udlø- se elektrisk stød eller brand. Batteri Undlad at lade batteriet ved tem- peraturer under 0oC og over 40oC. Undlad at bruge nogen form for transformer, generator eller jævn- strøm. Undlad at kortslutte batteriet. Po- lerne må ikke være i nærheden af metalgenstande som søm, møn- ter, klips osv. Udsæt ikke batteriet for regn eller vand. Et kortsluttet batteri kan for- årsage overophedning, brandfare, elektrisk stød og personskader. Værktøj og batteri må ikke opbe- vares ved temperaturer over 50oC. Undlad at tabe batteri eller beska- dige det på nogen måde. Batteriet må kun oplades i et ven- tilleret lokale.

- 6 - Bortskaffelse af elektrisk og elek- tronisk udstyr i overensstemmel- se med direktiv 2002/96/EF (WEE). Brug ikke den normale affaldsbe- holder til bortskaffelse af dette produkt. Brugt elektrisk og elektronisk ud- styr skal behandles separat i hen- hold til lovgivningen, der kræver passende behandling, genvinding og genbrug af disse produkter. I henhold til bestemmelserne, der er iværksat af EU-landende, kan privatpersoner, der er bosat her, gratis aflevere brugt elektrisk og elektronisk udstyr til udvalgte ind- samlingscentre. Hvis det er van- skelligt at finde et opsamlingscen- ter, der har tilladelse til bortskaf- felse, bedes De kontakte forhand- leren, hvor produktet er købt BRUGSANVISNING FOR MOMENTNØGLE Momentnøglen med fraslag er beregnet til at spænde/afspænde bolte og skruer. Den er ikke be- regnet som boremaskine. Aftrækker Ved tryk på aftrækkeren aktiveres LED lyset fortil (2) og motoren starter. Når du slipper aftrække- ren stopper værktøjet øjeblikke- ligt, mens LED lyset forbliver tændt i 5 sekunder. 3. Omskifter højre/venstre omløbsretning Værktøjet kører altid højre om, med mindre knappen for venstre rotation er trykket ned. Når maskinen kører mod venstre lyser LED blåt. For højre rotation tryk på omskifteren igen, blå LED-lys slukker og maski- nen kører højre om. 4. Anvil (firkant) Anvil passer til 3/8” og 1/2” krafttop. Husk at sætte toppen rigtigt fast inden brug. 5. Vinkelhoved Indstil vinkelhovedet til den ønskede vinkel. Der er 8 positioner at vælge mellem. 6. Momentregulering Klap til momentregulering åbnes og momentet indstilles til det ønskede ved hjælp af det medfølgende værktøj. 7. Li-ion batteri Batteriet skal lades I henhold til in- struktionerne her I vejledningen. ADVARSEL: Benyt kun værktøjet til det momentområde, det er beregnet til. 5 6 2 4 3 1 7

BRUGSANDVISNING FOR SKRUENØGLE Skruenøglen med fraslag er bereg- net til at spænde/afspænde bolte og skruer. Den er ikke beregnet som boremaskine. 1. Aftrækker Ved tryk på aftrækkeren aktiveres LED lyset fortil (2) og motoren star- ter. Når du slipper aftrækkeren stop- per værktøjet øjeblikkeligt, mens LED lyset forbliver tændt i 5 sekun- der. 3. Omskifter højre/venstre omløbsretning Værktøjet kører altid højre om, med mindre knappen for venstre omløbs- retning er trykket ned. Når maskinen kører mod venstre lyser LED blåt. For højre rotation tryk på omskifteren igen, blå LED-lys slukker og maski- nen kører højre om. 4. Bit tilslutning Nøglen passer kun til 1/4” sekskant bits. Du skal sikre, at bitten sidder rigtigt fast. 5. Vinkelhoved Indstil vinkelhovedet til den ønskede vinkel. Der er 8 positioner at vælge mellem. 6. Momentregulering Klap til momentregulering åbnes og momentet indstilles til det ønskede ved hjælp af det medfølgende værk- tøj. 7. Li-ion batteri Batteriet skal lades I henhold til in- struktionerne her I vejledningen. ADVARSEL: Benyt kun værktøjet til det momentområde, det er beregnet til. 5 6 2 4 3 1 7

kan være opstået under transport. Læs instruktionerne, før ibrugtagning. Tilslut / fjern batteri Batteriet skubbes på plads i slæden indtil det låser sig selv. 2. Tryk på den røde knap oven på bat- teriet og fjern batteriet. - 8 - BRUG Værktøjet er undersøgt på fabrikken, og vil fungere tilfredsstillende ved normalt brug mange år frem. Anvend ikke værktøjet ud over det, værktøjet er beregnet til. Garanti dækker ikke et sådant brug. 1. Skub batteriet på plads indtil det låser sig selv med et klik. Undgå at tvinge batteriet på plads, hvis det yder modstand. Modstand er tegn på, at batteriet er sat skævt i. 2. Værktøjets hastighed kan justeres med en FLAIR program speed. 3. (FLAIR program speed enheden kan tilkøbes.) 4. Vælg den ønskede bit og fastgør bitten i maskinens chuck. 5. 6. Aktiver aftrækkeren så LED lyset tænder og værktøjet starter. Aflæs momentet på det digitale display og indstil momentet, hvis nødven- digt. 7. Når det indstillede moment er nået, slår værktøjet selv fra ADVARSEL! Læs brugsanvis- ningen/instruktionerne før brug. Brug altid sikkerhedsbriller / per- sonværn. SKUB 1. TRYK 2. FJERN

Højre / venstre omløbsretning Tryk kun på knappen til højre / ven- stre omløbsretning når maskinen står helt stille. Højre (fremad) omløbsretning Værktøjet kører højre om, hvis det blå lys IKKE er tændt. Venstre (baglæns) omløbsretning Med et langvarigt tryk på F/R knap- pen vælger du mellem automatisk eller manuel valg af venstre rotati- on. Mode 1: Automatisk - Værktøjet går automatisk tilbage til højre om- løbsretning efter at have kørt i ven- stre omløbsretning. Mode 2: Manuel - Værktøjet bliver ved med at køre i venstre omløbs- retning, indtil operatøren vælger højre omløbsretning. Skift mode: Tryk F/R knappen ned indtil den blinker blåt - slip knappen. Momentregulering (1) Momentnøgle: Åben klappen. Brug en fastnøgle til at dreje firkan- ten indtil regulerings-hullet kommer til syne. ADVARSEL: Batteriet SKAL fjernes før momentet reguleres. Tryk aftrækkeren ind for at sikre at maskinen ikke er tilsluttet. 2. Drej reguleringsværktøjet med uret for større moment og mod uret for mindre moment. (2) Skruenøgle: Åben klappen og brug reguleringsværktøjet til at ændre momentet. ADVARSEL: Batteriet SKAL fjer- nes før momentet reguleres. Tryk aftrækkeren ind for at sikre at ma- skinen ikke er tilsluttet. Klap Regulering Firkantet hul Regulering Klap

LED indikator lys og lyd Status / betydning Handling Lyser rødt, gult og grønt samtidig i 1 sekund. Et langt beep 1 sekund. Motoren er tændt - Lyser rødt I 1 sekund. Et langt beep i 1 sekund. Momentet er ikke nået (NOK). Begynd montagen igen. Dobbelt iskruning Begynd montagen igen. Lyser grønt. Det indstillede moment er nået og tilspænd- ningen er OK. - Blinkter gult 5 gange. 5 korte beeps. Batterispændningen er ved at være lav Skift batteri til et fuldt opladet batteri. Lyser gult I 5 sekunder. Et langt beep I 5 sekunder. Batterispændingen er brugt. Maskinen stop- per. Skift batteri til et fuldt opladet batteri. Lyser blåt. Maskinen kører venstre om - Blinker rødt 2 gange. Motoren er for varm. Fjern batteriet og lad maskinen køle ned. Sæt batteriet på igen, og maskinen er klar. Blinker rødt 3 gange. Motoren er i stykker. Send maskinen til repa- ration. Blinker rødt 4 gange Løs forbindelse. Send maskinen til repa- ration. - 10 –

(Model: AT07 & AT14 serie) - 11– 1. Brug en fastnøgle og en skiftenøg- le til at løsne bolten og fjerne hele vinkelhovedet. 2. Indstil vinkelhovedet til den øn- skede vinkel og fastgør det igen til værktøjet. 3. Brug en fastnøgle og en skiftenøgle til at spæn- de bolten igen.

(Model: AT30S3) - 12– 1. Brug to skiftenøgler til at løsne bolten og fjerne hele vinkelhove- det. 2. Indstil vinkelhovedet til den øn- skede vinkel og fastgør det igen til værktøjet. 3. Brug to skiftenøgler til at spænde bolten igen..

4. Hvis den røde indikator ikke tæn- der, eller slukker efter kort tid, skal du kontakte din forhandler. 5. Under opladning blinker det grønne indikatorlys. Når batteriet er fuldt opladet slår en elektronisk kontakt fra, så batteriet ikke over-oplades. - Opladning vil ikke starter, hvis bat- teriet er varmt, f.eks. lige efter brug. Det gule indikatorlys (stand by) blinker indtil batteriet er kølet ned. 6. Hvis batteriet er 0oC eller under tager det længere tid at oplade bat- teriet. Batteriet lader kun til ca. 50% af fuld opladning I forhold til opladning under normale tempera- ture. 7. Det grønne indikatorlys lyser kon- stant, når batteriet er fuldt opladet. Li-ion batteri BEMÆRK 1. Batteriet er ikke opladet fra starten. Sørg for at batteriet lades op inden brug. 2. Fjern batteriet fra maskinen, hvis du ikke skal bruge maskinen i læn- gere tid. 3. Oplad batteriet hver 6. måned, også selvom det ikke har været I brug. Ladning af batteri- Li-on batteri BEMÆRK Undlad at sætte et koldt batteri (un- der 0oC) til opladning i et varmt loka- le. Lad batteriet stå i samme lokale som laderen mindst 1 time. Sørg for at afkøle laderen, hvis du lader mere end 2 batterier i træk. Undgå at røre ved kontakterne på laderen. 1. Sæt laderen i et ventileret område, der ikke er for varmt. 2. Tilslut laderen til el-nettet. 3. Vend batteriet på hovedet og skub det ind i laderen i pilens retning. Undgå at tvinge batteriet på plads. Modstand er tegn på, at batteriet er sat skævt i laderen. Flugtlinjer

Gult blink (1) Hvis batteriet er for koldt oplades det kun delvist, indtil det har nået en temperature på over 0oC. Indikatoren går fra gult blink til grønt blink, og laderen oplader normalt. Hvis indikatoren efter 70 minutter går fra gult blink til at lyse gult konstant, skal du kontakte din forhandler. (2) Hvis batteriet er for varmt (over 40oC), oplades det kun delvist indtil det har opnået en temperature på under 40oC. Indikatoren går fra gult blink til grønt blink, og laderen op- lader normalt. Hvis indikatoren efter 70 minutter går fra gult blink til at lyse gult konstant, skal du kontakte din for- handler. (3) Hvis batteriets spænding er for lav (under 4.4 V), oplades det kun delvist indtil det har nået en normal spænding. In- dikatoren går fra gult blink til grønt blink, og laderen opla- der normalt. Hvis indikatoren efter 70 minutter går fra gult blink til at lyse gult konstant, skal du kontakte din forhand- ler. Gult lys Batteri er ikke sat rigtigt i laderen. Hvis laderen stadig lyser gult, efter du har forsøgt at sætte batteriet i laderen igen, skal du kontakte din forhandler. Grønt blink Opladning er i gang Grønt blink Batteriet er opladet ca. 50%. Grønt blink Batteriet er opladet ca. 80%. Grønt lys Opladning er færdig. Batteriet er opladet 100%.

6.35 mm Sq. (1/4”) Screw Size M3 ~ M5 M3 ~ M5 Torque Range ( Hard joint ) 1.8 ~ 8 N-m (15.9 ~ 70.8 in-lb) 1.8 ~ 8 N-m (15.9 ~ 70.8 in-lb) Torque Range ( Soft joint ) 1.8 ~ 7 N-m (15.9 ~ 62 in-lb) 1.8 ~ 7 N-m (15.9 ~ 62 in-lb) Free Speed 400 ~ 800 r.p.m 400 ~ 800 r.p.m Weight With Battery 1.45 kg (3.19 lb) 1.45 kg (3.19 lb) Battery Type Li-ion 2.0A.h Li-ion 2.0A.h Charge Time Approx. 45 mins Approx. 45 mins MODEL ITEM AT07S3 AT14H2 Voltage 18 VDC 18 VDC Drive Size 9.5 mm Sq. (3/8”) 6.35 mm Hex. (1/4”) Screw Size M3 ~ M5 M4 ~ M6 Torque Range ( Hard joint ) 1.8 ~ 8 N-m (15.9 ~ 70.8 in-lb) 3.5 ~ 16 N-m (31 ~ 141 in-lb) Torque Range ( Soft joint ) 1.8 ~ 7 N-m (15.9 ~ 62 in-lb) 3.5 ~ 14 N-m (31 ~ 124 in-lb) Free Speed 400 ~ 800 r.p.m 200 ~ 500 r.p.m Weight W/O Battery 1.45 kg (3.19 lb) 1.45 kg (3.19 lb) Battery Type Li-ion 2.0A.h Li-ion 2.0A.h Charge Time Approx. 45 mins Approx. 45 mins -15 -

9.5 mm Sq. (3/8”) Screw Size M4 ~ M6 M4 ~ M6 Torque Range ( Hard joint ) 3.5 ~ 16 N-m (31 ~ 141 in-lb) 3.5 ~ 16 N-m (31 ~ 141 in-lb) Torque Range ( Soft joint ) 3.5 ~ 14 N-m (31 ~ 124 in-lb) 3.5 ~ 14 N-m (31 ~ 124 in-lb) Free Speed 200 ~ 500 r.p.m 200 ~ 500 r.p.m Weight W/O Battery 1.45 kg (3.19 lb) 1.45 kg (3.19 lb) Battery Type Li-ion 2.0 Li-ion 2.0 Charge Time Approx. 45 mins Approx. 45 mins MODEL ITEM AT30S3 Voltage 18 VDC Drive Size 9.5 mm Sq. (3/8”) Screw Size M5 ~ M8 Torque Range ( Hard joint ) 8 ~ 32 N-m (71 ~ 283 in-lb) Torque Range ( Soft joint ) 8 ~ 30 N-m (71 ~ 265 in-lb) Free Speed 200 r.p.m Weight W/O Battery 1.9 kg (4.18 lb) Battery Type Li-ion 2.0 Charge Time Approx. 45 mins -16 –

Sound pressure level (no load) LpA : dBA Uncertainty K : dB Sound power level (no load) LwA : dBA Uncertainty K : dB Vibration total value (no load) ahd : m/s2 Uncertainty K : m/s2 The declared noise levels and vibration total value has been measured in accord- ance with a standard test method and may be used for comparing one tool with an- other. The declared noise levels and vibration total value may also be used in a pre- liminary assessment of exposure. WARNING: − The noise and vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used; and − Need to identify safety measures to protect the operator that are based on an es- timation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is run- ning idle in addition to the trigger time). -17 –

For Models: WRTCA-30S3 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -18– Index No Description Q'ty Index No Description Q'ty Index No Description Q'ty a Clutch Assembly 1 d Washer 1 g Adjust Nut 1 b Steel Ball 3 e Spring 1 h Snap Ring 1 c Washer 1 f Adjust Washer 1 Index No Description Q'ty Index No Description Q'ty Index No Description Q'ty a Sun Gear Assembly 1 b Washer 1 d Gear Ring 1 (1) Bearing Seat 1 c Gear Cage Assembly 1 e Washer 2 (2) Ball Bearing 2 (1) Pin 3 f Thrust Ball Bearing 1 (3) Inverted Retaining 1 (2) Planet Gear 6 g Retaining Plate 1 (4) Snap Ring 1 (3) Gear Cage 1 (5) Sun Gear 1 (4) Needle Bearing 6

For Models: AT07S2 AT14S2 Index No Description Q'ty Index No Description Q'ty a Lock Nut 1 e (1) Angle Housing 1 b Lock Nut 1 (2) Needle Bearing 1 c Collar 1 f O-Ring 1 d Main Bevel Gear Assembly 1 g Screw 1 (1) Main Bevel Gear 1 h Bevel Gear Assembly 1 (2) Ball Bearing 3 (1) Bevel Gear 1 (3) Inverted Retaining Ring 1 (2) Ball Bearing 1 e Angle Housing Assembly 1 (3) Inverted Retaining Ring 1 i Lock Nut 1 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -19-

For Models: AT07H2 AT14H2 Index No Description Q'ty Index No Description Q'ty a Lock Nut 1 e (1) Angle Housing 1 b Lock Nut 1 (2) Needle Bearing 1 c Collar 1 f O-Ring 1 d Main Bevel Gear Assembly 1 g Screw 1 (1) Main Bevel Gear 1 h Bevel Gear Assembly 1 (2) Ball Bearing 3 (1) Bevel Gear 1 (3) Inverted Retaining Ring 1 (2) Ball Bearing 1 e Angle Housing Assembly 1 (3) Inverted Retaining Ring 1 i Lock Nut 1 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -20-

For Models: AT07S3 AT14S3 Index No Description Q'ty Index No Description Q'ty a Lock Nut 1 e (1) Angle Housing 1 b Lock Nut 1 (2) Needle Bearing 1 c Collar 1 f O-Ring 1 d Main Bevel Gear Assembly 1 g Screw 1 (1) Main Bevel Gear 1 h Bevel Gear Assembly 1 (2) Ball Bearing 3 (1) Bevel Gear 1 (3) Inverted Retaining Ring 1 (2) Ball Bearing 1 e Angle Housing Assembly 1 (3) Inverted Retaining Ring 1 i Lock Nut 1 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -21-

For Models: AT30S3 Index No Description Q'ty Index No Description Q'ty a Collar 1 e (2) Needle Bearing 1 b Lock Nut 1 f O-Ring 1 c Lock Nut 1 g Screw 1 d Main Bevel Gear Assembly 1 h Bevel Gear Assembly 1 (1) Main Bevel Gear 1 (1) Bevel Gear 1 (2) Ball Bearing 3 (2) Ball Bearing 1 (3) Inverted Retaining Ring 1 (3) Inverted Retaining Ring 1 e Angle Housing Assembly 1 i Lock Nut 1 (1) Angle Housing 1 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -22-

For Models: AT07H2 AT07S2 AT07S3 AT30S3 GEAR BOX UNITS For Models: AT14H2 AT14S2 AT14S3 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -23- Index No Description Q’ty Index No Description Q’ty Index No Description Q’ty a Washer 1 d Planet Gear 3 f Gear Box Assembly 1 b Planet Gear 3 e Gear Plate Assembly 1 (1) Gear Box 1 c Gear Cage Assembly 1 (2)Ball Bearing 1 Index No Description Q’ty Index No Description Q’ty Index No Description Q’ty a Washer 1 c Gear Cage Assembly 1 e Gear Box Assembly 1 b Planet Gear 6 d Gear Plate Assembly 1 (1) Gear Box 1 (2)Ball Bearing 1

For Models: AT07H2 AT07S2 AT07S3 AT30S3 AT14H2 AT14S2 AT14S3 On occasions when parts/part units are needed, please refer to the Part No. on exploding drawing and place orders to the suppliers. -24- Index No Description Q'ty Index No Description Q'ty a Upper Housing 1 m Connector Wire 1 b Lower Housing 1 n PC Board 1 c Brushless Motor Assembly ;w/driver 1 o Screw(φ3×8L) 2 d Connector 1 p Sensor & LED Assembly 1 e Motor Plate 1 q Cover 1 f Screw(M4×6L) 2 r Trigger Assembly 1 g Spring 1 s Spring 1 h Washer 1 t Cover 1 i Connecting Holder Assembly 1 u Screw (M3×P0.5×10L) 12 (1) Connecting Holder 1 v Washer (ψ3.3×ψ8) 2 (2) Ball Bearing(6801ZZ) 1 w Cover 1 j Marking Ring (P32,Yellow) 1 x F/R Valve 1 k PC Board 1 y Suspension Bail 1 l Connector Wire 1

Distributed by: Folke-Larsens Eftf. A/S Ejby Industrivej 106 DK - 2600 Glostrup www.folkelarsen.dk

(A) The angle head allowing multiple head positions. (B) User can distinguish the torque at a glance of color. (C) Torque adjustment. (D) LED light for work area illumination. (E) LED indicator provides simple process information to the operator. The signal is visible from any angle. (F) F/R button for ease of ergonomic operation. (G) Non-contact switch provides longer life with less downtime. Variable speed control trigger. (H) Shock absorbing, ergonomic grip provides less fatigue with well-balanced operation. ( I ) Easy attached sliding battery system. (J) Li-ion battery offers longer life with no memory effect. (K) Tool speed can be adjusted by the Du-Pas programmer. (A) (C) (D) (G) (E) (J) (F) (K) (B) (H) (I)

(B) 1/4” Hex driver. (C) User can distinguish the torque at a glance of color. (D) Torque adjustment. (E) LED light for work area illumination. (F) LED indicator provides simple process information to the operator. The signal is visible from any angle. (G) F/R button for ease of ergonomic operation. (H) Non-contact switch provides longer life with less downtime. Variable speed control trigger. ( I ) Shock absorbing, ergonomic grip provides less fatigue with well-balanced operation. (J) Easy attached sliding battery system. (K) Li-ion battery offers longer life with no memory effect. (L) Tool speed can be adjusted by the Du-Pas programmer. - 3 - (B) (A) (D) (E) (H) (F) (K) (G) (L) (C) (I) (J)

tions applicable in your country to reduce the risk of fire, electric shock and personal injury. Understand the following safety instructions before attempting to operate this product. Always wear eye protection when working with power tools. Keep these instructions in a safe place. SAVE THESE INSTRUCTIONS General Safety Rules Work Area Safety - 4 - Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flamma- ble liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Personal Safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A mo- ment of inattention while operat- ing power tools may result in seri- ous personal injury. Dress properly. Do not wear loose clothing or jewelry. Con- tain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Do not overreach. Keep proper footing and balance at all times. Proper footing and bal- ance enables better control on the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Tool Use and Care Use clamps or other practical ways to secure and support the work piece to a stable platform. Holding the work piece by hand or against your body is unstable and may lead to loss of control. Do not force tools. Use the cor- rect tool for your application. The correct tool will do the job better and safer at the rate for which it is de- signed. Do not use tool if switch does not turn it on or off. Any tool that can- not be controlled with the switch is dangerous and must be repaired. Store idle tools out of reach of children and other untrained per- sons. Tools are dangerous in the hands of untrained users. Check for misalignment or bind- ing of moving parts, breakage of parts, and any other condition that may affect the tool operation. If damaged, have the tool ser- viced before using. Many acci- dents are caused by poorly main- tained tools.

Use only accessories that are recommended by the manufac- ture for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. Service Tool service must be performed only by qualified repair person- nel. Service or maintenance per- formed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte- nance instructions may create a risk of electric shock or injury. Additional Safety Rules Battery Charger Caution: To reduce risk of injury, charge only the authorized batter- ies. Other types of battery may burst, causing personal injury and damage. Before using battery charger, read all instructions and cautionary markings on batteries, chargers and products using batteries. Do not allow anything to cover or clog the charger vents. Do not expose charger to rain, snow or wet conditions. To reduce the risk of damage to electric plug and cord, pull by plug rather than cord when disconnect- ing charger. Use of an attachment not recom- mended or sold by the manufac- turer may result in a risk of fire, electric shock, or injury to per- sons. Make sure cord for charger is lo- cated so that it will not be stepped on, tripped on, tripped over, or otherwise subjected to damage or stress. Do not abuse the power cord. Never use the cord to carry the charger. Keep cord away from heat, oil, water, sharp edges, or moving parts. Replace damaged cords immediately. Do not operate charger if it has been damaged in any way, take it to a qualified service center for re- pair. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Do not disassemble charger or battery cartridge, take it to a quali- fied service center when repair is required. Incorrect reassembly may result in a risk of electric shock or fire. Battery Pack Do not charge battery pack when temperature is below 0oC (32oF) or above 40oC (104oF). Do not attempt to use a step-down transformer, an engine generator or DC power receptacle. Do not short the battery pack: Do not touch the terminals with any conductive material. Avoid storing battery cartridge in a container with other metal objects such as nails, coins, paper clips, etc. Do not expose battery cartridge to water or rain. A battery short can cause large current flow, overheat- ing, possibly burns and even a break-down.

- 6 - Do not store the machine and battery pack in locations where the temperature may reach or ex- ceed 50oC (122oF). Do not incinerate the battery pack even if it is severely damaged or completely worn out. The battery pack can explode in a fire. Be careful not to drop, shake, or strike the battery. Do not charge inside a box or container of any kind. The battery must be placed in a well ventilat- ed are during charging. Do not dispose of battery packs into household waste, fire or wa- ter. Battery packs should be col- lected, recycled or disposed of in an environmentally-friendly manner. Call the authorized war- ranty centers for places to dis- pose of damaged or inoperable batteries. FUNCTIONAL DESCRIPTION FOR WRENCH This industrial shut off wrench is designed for nut tightening/loosening and screw driving/loosening. It is not appropriate to use for wood/mild steel drilling. Please refer to the fig- ure on this page to familiarize your- self with the major components of this tool before use. 1. Power Switch Depressing the power switch will energize the LED light (2) in front and the tool starts to rotate. When released, power to the motor will cease and the tool stops to work immediately. But the LED light will remain for 5 seconds then off. 3. Forward/Reverse Button The tool is always in forward opera- tion unless the Forward/Reverse but- ton is pressed. When the button is pressed, the blue LED shows and the tool will be in reverse operation. To get the tool back in forward op- eration, just simply press the button again and the blue LED would dis- appear and the tool is back in for- ward operation. 4. Anvil (Drive Shaft) The anvil will accept drive hex sock- et. Be sure the socket is fully inserted before operating tool. Otherwise, the socket may fly off and cause property damage or personal injury. 5. Angle Head Adjust the angle head kit to the de- gree you wished. (a 45o as one po- sition, total 8 positions for angle ad- justment). 6. Torque Adjustment Cover Open the torque adjustment cap. Use the torque adjustment tool to either tighten or loosen the spring until the desired torque is reached. 7. Li-ion Battery This battery provides electrical power to the motor. Please charge it ac- cording to the charging instruction listed in this manual. WARNING: Use the tool to either tighten or loosen nuts and screws ONLY in stipulated torque and voltage ranges. 5 6 2 4 3 1 7

FUNCTIONAL DESCRIPTION FOR SCREWDRIVER This industrial shut off screwdriver is designed for nut tightening/loosening and screw driving/loosening. It is not appropriate to use for wood/mild steel drilling. Please refer to the fig- ure on this page to familiarize your- self with the major components of this tool before use. 1. Power Switch Depressing the power switch will energize the LED light (2) in front and the tool starts to rotate. When released, power to the motor will cease and the tool stops to work immediately. But the LED light will remain for 10 seconds then off. 3. Forward/Reverse Button The tool is always in forward op- eration unless the For- ward/Reverse button is pressed. When the button is pressed, the blue LED shows and the tool will be in reverse operation. To get the tool back in forward operation, just simply press the button again and the blue LED would disap- pear and the tool is back in for- ward operation. 4. 1/4” Hex Driver This driver accepts only 1/4” (6.35mm) hexagonal bits. Be sure the bit is fully engaged by the chuck before operating tool. Otherwise, the bit may fly off and cause property damage or personal injury. 5. Angle Head Adjust the angle head kit to the degree you wished. (a 45o as one position, total 8 positions for an- gle adjustment). 6. Torque Adjustment Cover Open the torque adjustment cap. Use the torque adjustment tool to either tighten or loosen the spring until the desired torque is reached. 7. Li-ion Battery This battery provides electrical power to the motor. Please charge it according to the charg- ing instruction listed in this manu- al. WARNING: Use the tool to either tighten or loosen nuts and screws ONLY in stipulated torque and volt- age ranges. 5 6 2 4 3 1 7

accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. This tool kit contains: - 1 18V Cordless Shut off Angle Tool - 1 Torque adjustment tool - 1 Open end wrench - 1Hex L-wrench (For Hex. Type) - 4 Marking color ring - 1 Suspension bail - 1 Instruction manual - 1 Color box Attaching or Removing Battery Pack 1. To connect battery, line up the tracks and attach the battery pack. Slide toward the battery pack until it locks into position with a click. 2. To remove the battery pack, press the red button on the top of the bat- tery pack and release the battery pack. - 8 - OPERATIONS This product had been carefully in- spected prior to leaving the factory. It should provide you with years of satis- fying service under normal operating conditions. Do not, however, force the tool to perform outside its design parameters. Such usage will void the warranty. 1. Slide battery into the bottom of the housing handle until a click sound occurs. Do not force battery as it should slide easily into place with nominal force. Any difficulty doing so would indicate an incorrect alignment. 2. Tool speed can be adjusted by the extra programmer. (Purchase an additional pro- grammer) 3. Select a proper size drill/drive bit or socket and insert into the driver. 4. Depress the trigger to engage the LED light and the tool starts to work. Check the torque on the digi- tal tester to see if the desired torque reached. If not, adjust the torque to either tighten or loosen the spring. 5. Make sure the tighten torque of the bolts or screws before work. It may vary due to different material you tighten. When the torque is reach, the tool will shut off automatically. WARNING! Read the manual instruction before operating the tool. Always wear safety glasses or face-shields when operating this product. Failure to do so can result in dust, shavings or loose particles being thrown into your eyes. SLIDE 1.PRESS 2.RELEASE

Forward/ Reverse Rotation Switch Operation To prevent damage, do not press Forward/Reverse button until the anvil comes a complete stop. Forward Rotation Operation The tool is in forward operation if the blue light is not on. Reverse Rotation Operation By long press on the F/R switch, users are able to choose the mode of Reverse operation, either auto- matic or manual. Mode 1: Automatic – Tool returns to Forward operation automatically after reverse operation. Mode 2: Manual – Tool needs to be adjusted manually to return to For- ward operation after reverse opera- tion. How to adjust: Long press on the F/R switch and release it as seeing the flashing blue light is on. The mode is transformed successfully. Steps for Torque Adjustment 1. (1)For Wrench: Open the cover, use an open end wrench to ro- tate the square drive until the ad- just hole position appears in the area of the hole of cover. NOTE: MUST remove the bat- tery pack before adjusting the torque and press the trigger to make sure no power connected. Or, it may create a risk of injury. 2. Turn the torque adjustment tool clockwise to increase the torque and counterclockwise to decrease the torque. (2)For Screwdriver: Lift the torque adjustment over. Take the torque adjust tool and insert it to the quick change holder and turn until the ad- just hole shows up. NOTE: MUST remove the battery pack before adjusting the torque and press the trigger to make sure no power connected. Or, it may create a risk of injury. Cover Adjust Hole Square Hole Adjust Hole Cover

Status of the LED indicator and beeper Status of the tool Action to be taken Light up in red, yellow and green together for one second. A long beep for one second. The motor is switched on. - Light up in red for one second. A long beep for one second. The preset torque is not reached (NOK). The screwing fastener must be performed again. The screw is refas- tened after fastening (NOK). The screwing fastener must be performed again. Light up in green. The preset torque is reached and the tight- ening is OK. - Blinks in yellow for five times. Five short beeps. The battery power becomes low. Replace the battery with fully charged one. Light up in yellow for five se- cond. A long beep for five second. The battery power is used up, the tool stops immediately. Replace the battery with fully charged one. Light up in blue. The tool is in reverse operation. - Blinks in red for two times. The motor is too hot. Remove the battery and let the tool cool down, and then reattach the battery. The tool can work properly again. Blinks in red for three times. The motor is failed. Send to the service cen- ter. Blinks in red for four times. The connector wire is failed. Send to the service cen- ter. - 10 –

(For Models: AT07 & AT14 series) - 11– 1. Use an open end wrench and a special wrench to loosen the nut by turning in opposite direction to remove the angle head kit. 2. Adjust the angle head kit to the degree you wished then put it back on the tool (a 45o as one po- sition, total 8 positions for angle adjustment). 3. Use an open end wrench and a special wrench to tighten the nut by turning in opposite direc- tion to the complete angle adjustment.

(For Model: AT30S3) - 12– 1. Use two special wrenches to loos- en the nut by turning in opposite direction to remove the angle head kit. 2. Adjust the angle head kit to the degree you wished then put it back on the tool (a 45o as one po- sition, total 8 positions for angle adjustment). 3. Use two special wrenches to tighten the nut by turning in opposite direction to the complete angle adjustment.

4. If the power lamp (red) does not light immediately or goes out soon after the charger is plugged in, consult an authorized dealer. 5. During charging, the charging lamp (green) will start flashing. When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharg- ing. - Charging will not start if the battery pack is warm. For example, imme- diately after heavy-duty operation. The yellow standby lamp will be flashing until the battery cools down. 6. If the temperature of the battery pack is 0oC or less, charging takes longer to fully charge the battery pack than the standard charging time. Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal operation tem- perature. 7. Once the battery is fully charged, the green lamp will be lit to indicate the gone into a trickle charge mode. Li-ion Battery Pack [NOTE] 1. Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before first use. 2. Remove the battery pack when the tool is idle for a long time. 3. Recharge the battery pack once every 6 month even if the battery is not in use. Charging the battery - for Li-ion battery [NOTE] When charging a cool battery pack (below 0oC(32oF) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature. Otherwise battery pack may not be fully charged. Cool down the charger when charg- ing more than two battery packs consecutively. Do not insert your fingers/ nails into contact hole, when holding charger or any other occasions. 1. Place charger in a relatively cool and well-ventilated area. 2. Plug charger into the AC outlet. CAUTION: Ensure that the power source to be utilized conforms to the power requirement specified on the product nameplate. 3. Turn the battery up-side-down and slide the battery into charger while keeping the alignment marks line up. Slide the forward in the direction of the arrow. Do not force battery as it should slide easily into place with nominal force. Any difficulty doing so would indicate an incorrect align- ment. alignment marks

Yellow Flashing (1) When the temperature of the battery is too low (<0oC(<32oF)), it is in a trickle charge mode until the tem- perature of the battery goes up to over 0oC(<32oF). The lamp will change from the Yellow Flashing to Green Flash- ing automatically and start to charge. (If after 70 minutes, the lamp changes from yellow flashing to yellow lit, consult an authorized dealer.) (2) When the temperature of the battery is too high (>40oC(104oF)), it is in a trickle charge mode until the temperature of the battery drops to under 40oC(104oF). The lamp will change from the Yellow Flashing to Green Flashing automatically and start to charge. (If after 70 minutes, the lamp changes from yellow flashing to yellow lit, consult an authorized dealer.) (3) When the voltage of the battery is too low (below 14.4 voltage), it is in a trickle charge mode until the voltage of the battery reaches to the standard value. The lamp will change from the Yellow Flashing to Green Flashing auto- matically and start to charge. (If after 20 minutes, the lamp changes from yellow flashing to yellow lit, consult an au- thorized dealer.) Yellow Lit The battery and the charger are not connected. If the yellow lit still on after trying re-attach the battery, consul the an author- ized dealer. Green Flashing Now start charging Green Flashing Battery is approximately 50% charged. Green Flashing Battery is approximately 80% charged. Green Lit Charging is complete. (Fully charged.)

Please record the following information to expedite warranty work or parts order: Model No. Description 18V Cordless Shut off Angle Tool Serial No. Purchase Date: Purchased From: Address of Retailer: Please affix original or copy of sales receipt here to facilitate warranty works. Edition:R2