Fujitsu SMARTCASE S500 Assembly Instructions Manual

__________________________________________________________________________________________________________________________________________________________ Page 1 of 18 www.fujitsu.com Assembly Instructions SMARTCASE S500 & D3544-Sx _ ________________________________________________________________________________________________________

__________________________________________________________________________________________________________________________________________________________ Page 2 of 18 www.fujitsu.com Table of Contents Step 1 Preparing the Chassis ......................................................................................................................................... 3 Step 2 Installing the Heatsink ....................................................................................................................................... 4 Step 3 Inserting additional Modules (Memory / M.2 / …)............................................................................................... 7 Step 4 Mainboard Assembly ........................................................................................................................................ 10 Step 5 Optional Components ....................................................................................................................................... 12 Installing WLAN Antennas ...................................................................................................................................... 12 Speaker Assembly ................................................................................................................................................... 13 Installing USB Type C Extension Cable ................................................................................................................... 14 Step 6 Closing the Chassis ........................................................................................................................................... 15 Step 7 Adding Stands................................................................................................................................................... 17

__________________________________________________________________________________________________________________________________________________________ Page 3 of 18 www.fujitsu.com Step 1 Preparing the Chassis Open the chassis with two hands by putting some pressure on your thumbs to push the cover reverse. Remove top cover and unpack the accessories. (Chassis kit content) Rear Cover Remove protective foil of heat spreader pad!

__________________________________________________________________________________________________________________________________________________________ Page 4 of 18 www.fujitsu.com Step 2 Installing the Heatsink Fujitsu provides both a passive and an active heatsink solution, and a common mounting backplate. Before assembling the mainboard into the chassis, it is recommended to install the optional onboard components like cooler, RAM, M.2, etc.). Mounting Backplate Do not remove the insulating foil of the backplate, otherwise the mainboard may be damaged due to possible short circuit (backplate position) Note: Mounting holes are asymmetrical!

__________________________________________________________________________________________________________________________________________________________ Page 5 of 18 www.fujitsu.com Passive Heatsink Note: The assembly solution with the coloured plastic part as shown above will be replaced by an alternative “SoC die-crack-protection” implementation in future.  Hold the heatsink with one hand so that it doesn’t tilt while installing the screws  Assemble all 4 screws according to the order shown. Each screw can be tightened immediately!  Finally, remove the coloured plastic part by turning it carefully clockwise. This coloured plastic part is used for secure assembly of the heatsink in order not to damage the CPU die (“die crack protection”). After assembly, this part can be scrapped Note: Recommended mounting torque for heatsink screws: 0.6Nm (max. 0.8Nm) Passive heatsink positioning: Gaps of the passive heatsink must be located towards the border of the mainboard Mounting Backplate: Do not remove the insulating foil of the backplate, otherwise the mainboard may be damaged due to possible short circuit 2 3 4 1 5

__________________________________________________________________________________________________________________________________________________________ Page 6 of 18 www.fujitsu.com Active Heatsink Note: The assembly solution with the coloured plastic part as shown above will be replaced by an alternative “SoC die-crack-protection” implementation in future. Note: Recommended mounting torque for heatsink screws: 0.6Nm (max. 0.8Nm) Active heatsink positioning: Heatsink must be positioned according to picture Mounting Backplate: Do not remove the insulating foil of the backplate, otherwise the mainboard may be damaged due to possible short circuit  Hold the heatsink with one hand so that it doesn’t tilt while installing the screws  Assemble all 4 screws according to the order shown. Each screw can be tightened immediately!  Finally, remove the coloured plastic part by turning it carefully clockwise. This coloured plastic part is used for secure assembly of the heatsink in order not to damage the CPU die (“die crack protection”). After assembly, this part can be scrapped 2 3 4 1 5

__________________________________________________________________________________________________________________________________________________________ Page 7 of 18 www.fujitsu.com Step 3 Inserting additional Modules (Memory / M.2 / …) The following picture shows some possible M.2 modules Attention: Do not touch any pins! Touch the memory at the outside edges only. Do not stick a barcode onto any modules! The following procedure is recommended in order to ensure secure electrical contact:  Insert the memory angular and pay attention to the notch!  Remove the memory again completely from the DIMM socket!  Insert memory again  Press down the memory until it clicks into place  Do not press in the middle of the memory, but press down on the outside edges Mainboard M.2 2242 SSD/ Storage M.2 SSD / Storage 2280 M.2 2230 WLAN Memory

__________________________________________________________________________________________________________________________________________________________ Page 8 of 18 www.fujitsu.com WLAN module / M.2. module assembly First remove the M.2 mounting screws. Insert M.2 module angular into the socket (while paying attention to the coding / notch). Both modules, as shown in the picture, have to be touched on the outside edges only. For the M.2 SSD (left socket), the assembly nut and screw are pre-installed for a 2240mm module. In order to install a 2260 module, the 2240 assembly nut has to be moved to the 2260 position first. For a 2280 module, the 2240 assembly nut has to be removed, and the pre-installed M.2 WLAN (2230) nut is used for both M.2 2230 WLAN and M.2 2280 SSD Recommended torque for the M.2 screw is 0.2Nm, and 0.3Nm for the nut. 2240 screw / nut position Common 2280/2230 screw / nut position 2260 screw / nut position

__________________________________________________________________________________________________________________________________________________________ Page 9 of 18 www.fujitsu.com Sample installation M.2 2280 SSD module and M.2 2230 M.2 WLAN module: Both modules are fixed by one common screw.

__________________________________________________________________________________________________________________________________________________________ Page 10 of 18 www.fujitsu.com Step 4 Mainboard Assembly 1. Swing in the mainboard (rear chassis side) 2. Move it carefully to the final position Take care for the heat spreader pad! Protective foil must be removed first! Insert the chassis rear cover as shown above. Push down the mainboard carefully while the four mounting holes fit onto the chassis nuts. 1 2

__________________________________________________________________________________________________________________________________________________________ Page 11 of 18 www.fujitsu.com Assemble the four mounting screws (included in the chassis kit). Recommeded torque = 0.6Nm

__________________________________________________________________________________________________________________________________________________________ Page 12 of 18 www.fujitsu.com Step 5 Optional Components Installing WLAN Antennas Please check the color-coding of the antennas. On the chassis front side the antenna bays are marked black respectively gray. Please note that the plastic front bezel has to be removed first. Push the antenna cables completely through the opening in the housing and pay attention to the antenna cable notch (see red circles). Carefully install the WLAN antennas. The metal plate must not be bent. Insert the black antenna cable in the hooks (see red circles), and then plug the black antenna cable to socket #1 of the M.2 WLAN module. Plug the gray antenna cable to socket #2. Note: Consider correct installation / position of the antenna cable in order to avoid possible collision with the USB Typ- C connector

__________________________________________________________________________________________________________________________________________________________ Page 13 of 18 www.fujitsu.com Speaker Assembly Please note that the plastic front bezel has to be removed first.  Insert speaker into “rubber”  Install speaker+rubber in fronbezel  Speaker cable is led to mainboard via appropriate chassis aperture.  Re-assemble plastic front bezel carefully and install speaker connector to mainboard Speaker Rubber Speaker speaker location

__________________________________________________________________________________________________________________________________________________________ Page 14 of 18 www.fujitsu.com Installing USB Type C Extension Cable Install the USB Type C bracket to the chassis rear cover. Then connect the USB cable connector to the appropriate mainboard connector. The USB cable should be bent slightly as required.

__________________________________________________________________________________________________________________________________________________________ Page 15 of 18 www.fujitsu.com Step 6 Closing the Chassis Slide the cover on top of the chassis pushing it forward. Some pressure may be required.

__________________________________________________________________________________________________________________________________________________________ Page 16 of 18 www.fujitsu.com Close the chassis rear cover using the screws included in the kit delivery.

__________________________________________________________________________________________________________________________________________________________ Page 17 of 18 www.fujitsu.com Step 7 Adding Stands The desk stands included in the chassis kit can be used either for horizontal or vertical use. They can be fixed by plastic clips, in addition there are screws included for more secure stand assembly. Insert the clips into the holes of the stands.

__________________________________________________________________________________________________________________________________________________________ Page 18 of 18 www.fujitsu.com Contact FUJITSU Fujitsu Technology Solutions Gmbh Address: Bürgermeister-Ulrich-Straße 100 86199 Augsburg, Germany Phone: +49 821 804 0 Fax : +49 821 804 3329 E-mail: [email protected] Website: www.fujitsu.com/[Country Code] YYYY-MM-DD [Region Code] [Language Code] © 2018 Fujitsu Technology Solutions GmbH. Fujitsu, the Fujitsu logo are trademarks or registered trademarks of Fujitsu Limited in Japan and other countries. Other company, product and service names may be trademarks or registered trademarks of their respective owners. Technical data subject to modification and delivery subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded. Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which by third parties for their own purposes may infringe the rights of such owner. Install the stand to the chassis and fix them by the clips. Optionally, the stands can be secured by the screws. Horizontal Stand Position Vertical Stand Position