Haws 7460 Installation, Operation & Maintenance Instructions

NO. OOO2076521 (0) No 2080052(12) 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: [email protected]  website: www.hawsco.com Model 7460 Eye/Face Wash INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS LIMITED WARRANTY HAWS® warrants that all of its products are guaranteed against defective material or poor workmanship for a period of one year from date of shipment. HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to company within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that Haws has made no other warranties either expressed or implied in addition to those above stated, except that of title with respect to any of the products or equipment sold hereunder and that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale. The emergency equipment manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose, which they were intended. This product is intended to supplement first-aid treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries. NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR GIVEN BY HAWS. NOTE TO INSTALLER: Please leave this information with the Maintenance Department. SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL, PLEASE CALL: 1-800-766-5612 FOR PARTS CALL: 1-800-758-9378 (U.S.A. AND CANADA ONLY) MONDAY-THURSDAY: 6:00 A.M. – 4:00 P.M. PST FRIDAY: 6:00 A.M – 1:00 P.M. PST

LOCATION OF UNIT: The Model 7460 Eyewash should be installed in close proximity to potential accident areas. It should be clearly identified free from obstructions and easy to access. SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 PSI (2-6 ATM) flowing supply line pressure. Where sediment or mineral content is a problem, an inlet filter is recommended. PLUMBING CONNECTIONS: Inlet supply is female 1/2” IPS. Waste outlet is 1-1/4” IPS. TROUBLESHOOTING PROBLEM REPAIR CHECKLIST 1. No flow. 1. Check the main shut-off valve. 2. Insufficient water flow. 2. a. Verify minimum 30psi flowing supply line pressure. b. Probable clogging of flow control due to inadequate line flushing. Unscrew eye/face wash head and remove the four screws to disassemble the head. Clean flow control and reassemble head. See SP65 Installation Drawing for details. c. Remove cap located on L – Strainer using a 3/8” allen wrench to access and clean filter screen. 3. Eyewash or face wash stream do not meet desired eye level or are not balanced. 3. Possible blocked flow control. Possible non-leveled eyewash assembly. 4. Water does not drain properly. 4. Check the main waste line of your building to see if it does handle the capacity required for the entire drainage system. For more information about Haws products, see our website: www.hawsco.com © 2017 Haws® Corporation – All Rights Reserved HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.

(INCLUDES: EYE/FACE WASH HEAD (SHOWN), EYEWASH HEAD (NOT SHOWN), EYEWASH FLOW CONTROL (NOT SHOWN), DUST COVER (SHOWN)) APPROVED DRAWN PART NUMBER SCALE: SHEET OF REVISION DRAWING TYPE: SIZE: A BY ECN NO. PAGE DATE DATE ECN: REVISED PER CHKD Haws Corporation - All Rights Reserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. C R MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM ITEM DESCRIPTION THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER. PART NO. CLF 02/24/93 12 0002080052 7460 1:1 1 1 FV 11/23/17 . VWC 3 OF 4 PARTS BREAKDOWN 5175 2017 VWC

EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED SUCH THAT FLUSHING FLUID IS NOT LESS THAN 33" (838 mm) AND NOT GREATER THAN 53" (1346 mm) FROM SURFACE ON WHICH USER STANDS, AND 6.0" (153 mm) MINIMUM FROM WALL OR NEAREST OBSTRUCTION. 2 HEIGHT IS DETERMINED BY WATER FLOW PATTERN HEIGHT SHOWN, WHICH IN TURN, IS DEPENDENT ON IN-LINE SUPPLY PRESSURE. 3. DIMENSIONAL TOLERANCES: ±1/2" (12.7 mm). 4. WHEN INSTALLING THIS UNIT, LOCAL , STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN. APPROVED: DRAWN: PART NUMBER SCALE: SHEET OF REVISION DRAWING TYPE: SIZE: A BY: ECN NO. PAGE DATE: DATE: ECN: REVISED PER CHK'D.: Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. C R MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. C.H. 02/91 12 0002080052.D 7460 EYE/FACE WASH NA 1 1 FV 11/23/17 . VWC 4 OF 4 INSTALLATION 5175 2017 VWC 2