Haug EN SL MT Series Operating Instructions Manual

1 Notes on operating instructions ................................................................................. 5 1.1 Pictorial markings used ................................................................................................. 5 2 Safety ............................................................................................................................ 6 2.1 Intended use .................................................................................................................. 6 2.2 Danger sources ............................................................................................................. 7 2.3 Installer qualifications .................................................................................................... 7 2.4 Operator qualifications .................................................................................................. 7 3 Description of unit ....................................................................................................... 8 4 Installation .................................................................................................................... 9 4.1 Important installation instructions ................................................................................. 9 4.2 Setting up, connecting ................................................................................................ 10 5 Application ................................................................................................................. 11 5.1 Putting into operation .................................................................................................. 11 6 Remedy of defects ..................................................................................................... 12 6.1 Troubleshooting .......................................................................................................... 13 7 Maintenance and repairs ........................................................................................... 14 7.1 Replacing fuse ............................................................................................................. 14 7.2 Accessories .................................................................................................................. 14 8 Technical data ............................................................................................................ 15 8.1 Characteristics and specification ................................................................................ 15 8.2 Supply voltage ............................................................................................................. 15 8.3 Ambient conditions ...................................................................................................... 16 8.4 Housing ........................................................................................................................ 17 9 Disposal ..................................................................................................................... 18

Page 5 Keep in a safe place for future reference! Types: EN SL (MT) 230 V 01.7906.005 EN SL (MT) 115 V 01.7907.005 EN SL (MT) 100 V 01.7907.055 1 Notes on operating instructions In these operating instructions, the power pack EN SL (MT) is also referred to as "unit". 1.1 Pictorial markings used  In these operating instructions NOT FOR USE by persons with pacemaker! WARNING! High voltage! Danger of fatal accidents! Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off! CAUTION! Important instructions!  On the unit WARNING! High voltage! Danger of fatal accidents! Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off!

Persons wearing heart pacemakers must maintain a safety distance of more than 50 cm from the ionizing unit! Make sure that you read and observe the operating instructions of the connected ionizing units! _____________________________________________________________________________________ The unit is operationally safe, provided that it is operated in accordance with its intended use. In case of misuse, dangers may result: - for life and limb of the operator, - for the unit and other assets. Also note Chapter 4.1 (Important installation notes, page 9). 2.1 Intended use CAUTION! Do not install or use the unit in areas subject to explosion hazards! The unit is intended exclusively for the high-voltage supply of HAUG ionizing units. It generates an alternating high tension of approx. 7 – 8 kV. It is intended, in connection with an ionizing unit, for the removal of electrostatic charges from, for example, glass, paper, plastics etc. For reasons of safety, unauthorized conversions and modifications of the unit are not permitted. The installation and operating conditions indicated in these Operating Instructions must be adhered to.

Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off! ____________________________________________________________________________________ Defective high-voltage terminals and cables may lead to danger of electric shocks. Shut down the unit immediately in case of visible damage and suspected electrical defects. 2.3 Installer qualifications The unit may be installed by trained electricians only. The above mentioned person must have read the operating instructions and must follow the instructions, notes and safety advice. 2.4 Operator qualifications The unit may be maintained and put into operation by trained electricians only or by authorized persons informed about the potential dangers. The above mentioned persons must have read the operating instructions and must follow the instructions, notes and safety advice.

Page 8 3 Description of unit Figure 1 1. Mains switch: Switch lights up green when the unit is switched on. 2. Ground connection Figure 2 3. High-voltage terminals 4. Check fuse (for replacement, refer to Chapter 7.1, page 14) 5. Connection to supply voltage 1 2 3 4 5

person must have read the operating instructions and must follow the instructions, notes and safety advice. 4.1 Important installation instructions ____________________________________________________________________________________ WARNING! High voltage! Danger of fatal accidents! Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off! ____________________________________________________________________________________ The operation of the unit is not affected by the position in which it is installed. However, we recommend installing the unit so that the high-voltage terminals points downwards (to protect it from humidity, oil and dirt). Do not place the unit on a surface generating or radiating heat. Avoid installation positions exposed to direct sunlight.

_____________________________________________________________________________________ WARNING! High voltage! Danger of fatal accidents! Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off! _____________________________________________________________________________________ 1. Before connecting always check that the unit is suitable for the local mains voltage (the voltage is indicated on the name plate). Incorrect mains voltage may result in damage to the unit. 2. Set up unit at the required site of usage (if required, attach using the enclosed holders). 3. Ensure that the unit is switched off (for mains switch, refer to Figure 1, item 1, page 8). 4. Connect ionizing units to high-voltage terminals. 5. Always connect unit to a socket with functioning ground wire. Always use the supplied mains cable with its integrated ground wire. 6. Put unit into operation.

instructed in the potential dangers. The above mentioned persons must have read the operating instructions and must follow the instructions, notes and safety advice. The unit is intended exclusively for the high-voltage supply of HAUG ionizing units. It generates an alternating high tension of approx. 7 – 8 kV. It is intended, in connection with an ionizing unit, for the removal of electrostatic charges from, for example, glass, paper, plastics etc. 5.1 Putting into operation Preconditions: The power pack and the ionizing unit must be connected correctly. 1. Switch on unit using the mains switch (refer to Figure 1, item 1, page 8).

Page 12 6 Remedy of defects _____________________________________________________________________________________ WARNING! High voltage! Danger of fatal accidents! Do not open unit! WARNING! Only plug in/unplug coaxial connector when the unit is switched off! _____________________________________________________________________________________ CAUTION! The units include a thermal cut out. If the unit overheats at the ionizing unit due to short circuiting, the thermal cut out will switch off the unit. The power pack can only be put back into operation once the short-circuit has been removed and the unit has cooled down (approx. 15 minutes)! Any remedy of defects must be carried out by trained electricians only. The above mentioned person must have read the operating instructions and must follow the instructions, notes and safety advice. In case of defects regarding the power pack and the ionizing unit, please check for correct installation and fusing first (for replacement, refer to Chapter 7.1 page 14).

Page 13 6.1 Troubleshooting Faults Measures No ionization Check mains voltage Check fuse (for replacement, refer to Chapter 7.1, page 14) Check connection Clean ionizing unit Check ionizing unit for damage. If damaged, immediately shut down and secure against restarting. If this does not remedy the fault, please return the unit with the ionizing unit to HAUG for checking (see reverse).

Page 14 7 Maintenance and repairs _____________________________________________________________________________________ WARNING! High voltage! Danger of fatal accidents! Do not open unit! _____________________________________________________________________________________ This unit does not include any parts which can be maintained or repaired by the operator. HAUG only is authorized to repair or calibrate the unit. Should the unit prove defective or if a defect is suspected, switch off unit immediately and secure against subsequent reuse. 7.1 Replacing fuse 1. Switch off unit. 2. Determine and remove the cause for the blown fuse. 3. Detach the fuse holder using a screwdriver and lift out. 4. Replace fuse and reattach fuse holder. Use the following fuses only: Unit type Fuse EN SL (MT) 100 / 115 V T 500 mA L 250; 5x20 mm EN SL (MT) 230 V T 250 mA L 250; 5x20 mm The unit type and the rated voltage are indicated on the nameplate. Only use fuses of the type indicated. 7.2 Accessories Article Order number One Point Ionizer 03.8510.200 Punkt – Elektrode XP 03.8513.200 Punkt – Elektrode XP (Set) 23.8513.100 U – Elektrode 05.8091.100 U – Elektrode (Set) 23.8091.100

Reference temperature 23 °C High-voltage terminals 2 HAUG High-voltage terminals High voltage U = approx. 7 - 8 kV Short-circuit current Ik ≤ 5 mA Cannot be used in pulsed mode 8.2 Supply voltage CAUTION! Always connect the PE conductor (green/yellow conductor) to the protective earth of the mains! Unit type Nominal value Operating range Frequency range Power input EN SL (MT) 100 VAC ±10 % 50 - 60 Hz Pmax = 40 VA EN SL (MT) 115 VAC ±10 % 50 - 60 Hz Pmax = 40 VA EN SL (MT) 230 VAC ±10 % 50 - 60 Hz Pmax = 40 VA

+5 °C to +45 °C Extreme range for storage and transport -15 °C to +60 °C Humidity: Rated application range Air pressure: Rated application range 800 mbar to 1060 mbar Vibrations: Extreme range for storage and transport max. 1.5 g (10 to 55 Hz), 1 h Shock max. 15 g in each direction 10 20 30 40 50 60 70 80 90 %RF 5 10 15 20 25 30 35 40 °C

IP 20 Protection class I Overvoltage category II Pollution severity 2 Connection to supply voltage Mains cable via socket for non-heating apparatus Dimensions: Height approx. 170 mm Width approx. 110 mm Depth approx 100 mm Weight: approx. 3,5 kg

the disposal of the unit!

V 08-1 16.09.16 EN SL-MT v08-1gb.doc made by HAUG GmbH & Co.KG Friedrich-List-Straße 18 D-70771 Leinfelden-Echterdingen Telefon 07 11 / 94 98 - 0 Telefax 07 11 / 94 98 - 298 www.haug.de E-Mail: [email protected] HAUG Biel AG Postfach CH-2500 Biel/ Bienne 6 Johann-Renfer-Strasse 60 CH-2500 Biel/ Bienne 6 Telefon 0 32 / 3 44 96 96 Telefax 0 32 / 3 44 96 97 www.haug.de E-Mail: [email protected]