Harbor Freight Tools 91615 Assembly And Operating Instructions

ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 ® 91615

SKU 91615 Page 2 DESCRIPTION 24” H X 20-5/8” Dia. Chrome-Plated Tube Steel with Red Nylon Padded Cushion and Floor Guards 7.70 Lbs. 350 Lbs. ITEM Dimensions Construction Net Weight Max. Weight Capacity Specifications Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When assembling/using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equip- ment. Read all instructions before using this product! 1. Keep work area clean. Cluttered areas invite injuries. 2. Keep children away. Children must never be allowed in the work area. Do not let children sit upon this product. This product can tip over and cause injury. 3. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. 4. Use eye protection. Always wear ANSI approved impact safety goggles when assembling this product. 5. Do not overreach. Keep proper footing and balance at all times when sitting upon this product. Never stand on this product. For sitting only. Be sure this product is level after assembly. 6. Replacement parts. If repairs are necessary, use only identical replacement parts. Use of any other parts will void the warranty. 7. Avoid sharp edges. Machined edges may cause injury if handled without caution. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SKU 91615 Page 3 Unpacking When unpacking, check to make sure the following parts are included that are listed on Page 4. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Assembly Instructions 1. The 24” Handy Shop Stool is perfect for working on projects in a work shop, garage, or as a drafting stool. Arrange all parts to be assembled on a clean, smooth, flat surface. 2. Insert the Plastic Cross Brace (4) into the ends of the Stool Legs (3) (the shorter side). Match up predrilled holes and thread in Short Screws (7). Tighten Short Screws securely. See Figure A. Plastic Cross Brace (4) Leg Holder (6) Bolts (8) Stool Legs (3) Short Screws (7) Figure A Figure B Floor Guards (5) Round Brace (2) Maintenance 1. Keep the 24” Shop Stool indoors to avoid rust. 2. Wipe surfaces with a damp cloth and a mild detergent. Rinse off and dry throughly. 3. Check hardware periodically to be sure Stool is secure. Bolt (8) Bolt (10) Figure C Round Brace (2) Stool Legs (3) Bolt (12) Lock Nut (11) 3. Place Floor Guards (5) on the end of all four Stool Legs (3). See Figure B. Attach the Round Brace (2) to the inside of the Stool Legs (3), matching up the predrilled holes and securing with Bolts (12) and Lock Nuts (11). Tighten securely. See Figure C. 4. Assemble Stool Top (1) with Pad using Bolts (8). From the underside of the Stool Top assembly (1), attach the Stool Legs (3) by firmly fastening them with the four Leg Holders (6). Use Bolts (8) in eight places. Tighten securely. See Figure A. 5. In the center of the Cross Brace (4) firmly fasten the Stool Top (1) with Bolt (10). See Figure B. Tighten all Screws and Lock Nuts so the Stool is firm and will not wobble. Check hardware before use to be sure Stool is secure. Note: Do not stand upon this Stool.

SKU 91615 Page 4 Parts List 1 1 4 1 4 4 Stool Top w/Pad Round Brace Stool Legs Plastic Cross Brace Floor Guards Leg Holder PART # DESCRIPTION QTY 1 2 3 4 5 6 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESEN- TATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. 1 2 10 4 11 Diagram Use Wrench and Screwdriver (not provided) PART # DESCRIPTION QTY 7 8 10 11 12 6 4 12 1 4 4 Short Screw (1/2”) Bolt (1/2”) Bolt (1-3/8”) Lock Nut Bolt (1-3/4”) 8 7 5 3 12 8 7